Chauvet COLORado Batten 72 Tour User manual

User Manual

Edition Notes
COLORado™ Batten 72 Tour User Manual Rev. 01d
Edition Notes
The COLORado™ Batten 72 Tour User Manual Rev. 01d
covers the description, safety
precautions, installation, programming, operation, and maintenance of the
COLORado™ Batten 72 Tour fixture (SW Ver. 1.3). CHAUVET®
released this edition
of the COLORado™ Batten 72 Tour User Manual Rev. 01d in August 2010.
Trademarks
CHAUVET® is a registered trademark of CHAUVET & Sons Inc. (d/b/a CHAUVET® or
Chauvet). The CHAUVET® logo in its entirety including the Chauvet name and the
dotted triangle, and all other trademarks on this manual pertaining to services, products
or marketing statements (example: It’s Green Thinking™) are owned or licensed by
CHAUVET®. Any other product names, logos, brands, company names, and other
trademarks featured or referred to within this document are the property of their
respective trademark holders.
Copyright Notice
CHAUVET® owns the content of this user manual in its entirety, including but not
limited to pictures, logos, trademarks, and resources.
© Copyright 2010 CHAUVET®
All rights reserved
Electronically published by CHAUVET® in the United States of America
Manual Usage
CHAUVET® authorizes its customers to download and print th
is manual for
professional information purposes only. CHAUVET® expressly prohibits the usage,
copy, storage, distribution, modification, or printing of this manual or its content for any
other purpose without its written consent.
Document Printing
For better results, print this document in color, on letter size paper (8.5 x 11 inches),
double sided. If using A4 paper (210 x 297 mm), configure your printer to scale the
content of this document to A4 paper.
Intended Audience
Any person in charge of installing, operating, and/or maintaining the COLORado™
Batten 72 Tour should read the guide that shipped with it as well as this manual in their
entirety before installing, operating, or maintaining this product.
Disclaimer
CHAUVET® believes that the information contained in this manual is accurate in all
respects. However, CHAUVET® assumes no responsibility for any error or omissions
in this document. CHAUVET® reserves the right to revise this document and to make
changes from time to time in thecontent hereof without obligation of CHAUVET® to
notify any person or company of such revision or changes. This does not constitute in
any way a commitment by CHAUVET® to make such changes. CHAUVET® may issue
a revision of this manual or a new edition of it to incorporate such changes.
CHAUVET®
Publications Hot
Line
If you have any comments about the accuracy of this document or general suggestions
regarding how we can improve it, please call us at [phone] (US callers) or +1-
954-929-1115 (international callers). You can download the latest versions of all
CHAUVET® products’ manuals from www.chauvetlighting.com.
Document
Revision The COLORado™ Batten 72 Tour User Manual Rev. 01d supersedes all previous
versions of this manual. Please discard any older versions of this manual you may
have, whether in printed or electronic format, and replace them with this version.
Author Editor Manager PD Manager
O. Desmonteix D. Couppe M. Graham F. Sellers
Product at a
Glance Use on Dimmer

Auto Programs

Outdoor Use

Auto-ranging Power Supply

Sound Activated

Replaceable Fuse

DMX

User Serviceable

Master/Slave

Duty Cycle


Table of Contents
COLORado™ Batten 72 Tour User Manual Rev. 01d -a-
Table of Contents
1. Before you Begin.............................................................................................................1
What is Included.............................................................................................................................1
Unpacking Instructions ...................................................................................................................1
Typographic Conventions...............................................................................................................1
Icons Conventions..........................................................................................................................1
Safety Notes...................................................................................................................................2
Expected LED Lifespan..................................................................................................................2
2. Introduction.....................................................................................................................3
Product Description........................................................................................................................3
Features.........................................................................................................................................3
Additional Features....................................................................................................................................3
Options......................................................................................................................................................3
DMX Channel Summary.................................................................................................................4
Product Overview...........................................................................................................................5
3. Setup................................................................................................................................6
AC Power.......................................................................................................................................6
Power Linking............................................................................................................................................6
AC Plug.....................................................................................................................................................6
Fuse Replacement.....................................................................................................................................6
Lens Replacement..........................................................................................................................7
DMX Linking...................................................................................................................................7
DMX Modes...............................................................................................................................................7
Master/Slave Connectivity..........................................................................................................................7
ID Addressing.................................................................................................................................8
Mounting........................................................................................................................................8
Orientation.................................................................................................................................................8
Rigging......................................................................................................................................................8
4. Operation.........................................................................................................................9
Control Panel Description...............................................................................................................9
Control Options ..............................................................................................................................9
Programming..................................................................................................................................9
DMX Personality........................................................................................................................................9
DMX Control Without ID Addressing...........................................................................................................9
DMX Control With ID Addressing..............................................................................................................10
Static Color..............................................................................................................................................10
Auto Programs.........................................................................................................................................10
Edit Customs...........................................................................................................................................10
Master/Slave............................................................................................................................................10
Color Settings..........................................................................................................................................11
Dimmer Curves........................................................................................................................................11
Control Panel Lock...................................................................................................................................11
Program Upload.......................................................................................................................................11
Reset.......................................................................................................................................................12
Whites Setting .........................................................................................................................................12
Fan Setting..............................................................................................................................................12
TOUR Notes.................................................................................................................................13
Master Dimmer ........................................................................................................................................13
Red, Green, Blue White, and Amber Color Selection................................................................................13
Color Macros...........................................................................................................................................13
Strobe .....................................................................................................................................................13
ID Address Selection................................................................................................................................13
Auto ........................................................................................................................................................13
Dimmer Speed.........................................................................................................................................13
Menu Map....................................................................................................................................14

Table of Contents
-b- COLORado™ Batten 72 Tour User Manual Rev. 01d
DMX Values .................................................................................................................................15
TOUR...................................................................................................................................................... 15
BLOCK1.................................................................................................................................................. 16
BLOCK2.................................................................................................................................................. 16
ARC1...................................................................................................................................................... 17
ARC1 + D................................................................................................................................................ 17
ARC2...................................................................................................................................................... 17
ARC2 + D................................................................................................................................................ 17
ARC2 + S................................................................................................................................................ 17
HSV ........................................................................................................................................................ 17
5. Technical Information...................................................................................................18
General Maintenance....................................................................................................................18
Troubleshooting Guide..................................................................................................................19
Exploded View..............................................................................................................................20
Photometric Data..........................................................................................................................21
Returns Procedure........................................................................................................................22
Claims..........................................................................................................................................22
Contact Us....................................................................................................................................22
Technical Specifications................................................................................................................23

Before you Begin
COLORado™ Batten 72 Tour User Manual Rev. 01d August 23, 2010 -1-
1. Before you Begin
What is
Included
•One COLORado™ Batten 72 Tour
•One power cord
•One safety cable
•Warranty Card
•User Manual
Unpacking
Instructions
Immediately upon receiving a fixture, carefully unpack the carton. Check the box or
flight case contents to ensure that all parts are present and that they are in good
condition. If any part appears damaged from shipping, or if the carton show signs of
mishandling, notify the shipper immediately. In addition, retain the box and all the
packing material for inspection.
In any event, save the carton and all packing material because, in case that you have to
return the fixture to the factory, you will have to do so in its original box or flight case,
with its original packing. See the Claims section in the Technical Information chapter.
Typographic
Conventions
Convention Meaning
1~512 A range of values
50/60 A set of mutually exclusive values in the text
[10] A DIP switch to be configured
Claims A fixture function, a new term, a section or a chapter
“COLORado™ UM” The name of another publication or manual
<SET> A button to be pressed on the fixture’s control panel
Settings A menu option that can be selected but not modified
MENU > Settings A sequence of menu options to be followed
[1~10]
A range of menu values of which one can be selected
Yes/No A set of mutually exclusive menu options to choose
ON A value to be entered or selected
Icons
Conventions
Icons Meaning
This icon indicates critical installation, configuration, or operation
information. Failure to comply with this information may render
the fixture partially or completely inoperative, damage third-party
equipment, or cause harm to the user.
This icon indicates important installation or configuration
information. Failure to comply with this information may prevent
the fixture from functioning correctly.
This icon indicates useful, although non-critical information.
The term “DMX” used throughout this document refers to the USITT DMX512-A
transmission protocol.

Before you Begin
-2- COLORado™ Batten 72 Tour User Manual Rev. 01d
Safety Notes
Please read the following notes
carefully because they include important safety
information about the installation, usage, and maintenance of this product.
It is important to read all these notes before starting to work with this product.
There are no user serviceable parts inside the COLORado™ Batten 72 Tour. Any
reference to servicing this unit you may find from now on in this User Manual
will only apply to properly CHAUVET® certified technicians. Do not open the
housing or attempt any repairs unless you are one of them.
Please refer to all applicable local codes and regulations for proper installation
of the COLORado™ Batten 72 Tour.
Keep this manual for future consultation. If you sell the COLORado™ Batten 72
Tour to another user, make sure that they also receive this manual.
Personal Safety
•Avoid direct eye exposure to the light source(s) while they are on.
•Always disconnect the COLORado™ Batten 72 Tour from its power source before
servicing.
•Always connect the COLORado™ Batten 72 Tour to a grounded circuit to avoid
the risk of electrocution.
•Do not touch the COLORado™ Batten 72 Tour’s housing when operating.
Mounting and Rigging
•This product is for indoor use only! To prevent risk of fire or shock, do not expose
this product to rain or moisture.
•Make sure there are no flammable materials close to the fixture(s) while operating.
•When hanging this fixture, always secure it to a fastening device using the
included safety cable.
Power and Wiring
•Always make sure that you are connecting the COLORado™ Batten 72 Tour to the
proper voltage, as per the specifications in this manual or on the product’s sticker.
•Never connect the COLORado™ Batten 72 Tour to a dimmer pack.
•Make sure the controller’s external voltage adapter housing or cable is not
cracked, crimped, or damaged.
•Never disconnect the fixture by pulling or tugging on the power cable.
Operation
•Maximum ambient temperature (Ta) is 104° F (40° C). Do not operate the fixture at
a higher temperature.
•In case of a serious operating problem, stop using this product immediately!
In the unlikely event that your COLORado™ Batten 72 Tour may require service,
please contact CHAUVET® Technical Support.
Expected LED
Lifespan
LEDs gradually decline in brightness over time, mostly because of heat. Packaged in
clusters, LEDs exhibit higher operating temperatures than in ideal or singular optimum
conditions. For this reason, using all color LEDs at their fullest intensity significantly
reduces the LEDs’ lifespan. Under normal conditions, this lifespan can be of 40,000 to
50,000 hours. If extending this lifespan expectancy is vital, lower the operational
temperature by improving fixture ventilation and reducing the external temperature. In
addition, limiting the overall projection intensity may also help to extend the LEDs life.

Introduction
COLORado™ Batten 72 Tour User Manual Rev. 01d August 23, 2010 -3-
2. Introduction
Product
Description
The COLORado™ Batten 72 Tour is RGBW linear LED wash light fixture. It consists of
a single module that accommodates the internal power supply, the main control, the
control panel, the LED drivers, the LED boards and lenses as well as the power and
signal connectors. It features two mounting brackets that double as floor mount feet
and hanging support brackets. These brackets have tilt adjust knobs to simplify
mounting this fixture.
Features
•3, 4, 5, 6, 7, 9, 13, or 15-channel RGBWA LED linear wash light
•Operating modes
3-channel: RGB control
3-channel: HSV control (hue, saturation and value)
4-channel: RGB, dimmer
5-channel: RGBWA control
6-channel: RGBWA, dimmer
7-channel: RGBWA, dimmer, strobe
9-channel: RGB for individual block control
13-channel: RGBWA, ID addressing, dimmer, dimmer speed, strobe,
macro, auto/custom, and module select
15-channel: RGBWA for individual block control
•Built-in automated programs via DMX
•Recall custom programs via DMX
•RGBWA color mixing with or without DMX control
Additional Features
•Five distinct dimming curves
•Additional power output: max 13 units @ 120 V
•LED display with lock-out feature
•NEUTRIK® powerCON connectors
•3-pin and 5-pin DMX input and output connectors
•Adjustable feet double as hanging bracket
Options •Optical systems: 30°(installed), 25º x 6°(CL20x25x6) optional

Introduction
-4- COLORado™ Batten 72 Tour User Manual Rev. 01d
DMX Channel Summary
TOUR
DMX Channel
Function
ARC1
DMX Channel
Function
1
Master Dimmer
1
Red
2
Red
2
Green
3
Green
3
Blue
4
Blue
5
White
ARC1 + D
DMX Channel
Function
6 Amber 1 Master Dimmer
7 Macro + White Balance 2 Red
8
Strobe
3
Green
9
Auto Programs + Fan
4
Blue
10
Auto Speed
11
Dimmer Speed
ARC2
DMX Channel
Function
12
ID Address
1
Red
13
Block Selection
2
Green
3
Blue
BLOCK1
DMX Channel
Function
4
White
1
Block 1 Red
5
Amber
2
Block 1 Green
3
Block 1 Blue
ARC2 + D
DMX Channel
Function
4
Block 2 Red
1
Master Dimmer
5 Block 2 Green 2 Red
6 Block 2 Blue 3 Green
7
Block 3 Red
4
Blue
8
Block 3 Green
5
White
9
Block 3 Blue
6
Amber
BLOCK2
DMX Channel
Function
ARC2 + S
DMX Channel
Function
1
Block 1 Red
1
Master Dimmer
2
Block 1 Green
2
Red
3
Block 1 Blue
3
Green
4
Block 1 White
4
Blue
5
Block 1 Amber
5
White
6
Block 2 Red
6
Amber
7 Block 2 Green 7 Strobe
8
Block 2 Blue
9
Block 2 White
HSV
DMX Channel
Function
10
Block 2 Amber
1
Hue
11
Block 3 Red
2
Saturation
12
Block 3 Green 3 Value
13 Block 3 Blue
14
Block 3 White
15
Block 3 Amber

Introduction
COLORado™ Batten 72 Tour User Manual Rev. 01d August 23, 2010 -5-
Product Overview
Control
Panel
3-Pin DMX
In/Out
Safety
Eye Bolt
Power In
Tilt
Adjustment
Knob
Power Out
5-Pin DMX
In/Out
Tilt
Adjustment
Knob
Fuse

Setup
-6- COLORado™ Batten 72 Tour User Manual Rev. 01d
3. Setup
AC Power
The COLORado™ Batten 72 Tour has an auto-ranging power supply that can work
with an input voltage range of 100~240 VAC, 50/60 Hz.
Make sure that you are connecting this product to the proper voltage, as per the
specifications in this guide, the product’s user manual or on the product’s sticker.
Always connect the COLORado™ Batten 72 Tour to a protected circuit with an
appropriate electrical ground to avoid the risk of electrocution or fire.
To determine the power requirements for the COLORado™ Batten 72 Tour see the
label affixed to the side of the fixture. Alternatively, you may refer to the corresponding
specifications chart in the Technical Information chapter of this manual.
The listed current rating indicates the maximum current draw during normal operation.
Please refer to the Sizing the Circuit Breakers section in the Appendix chapter of this
manual.
Never connect the COLORado™ Batten 72 Tour to a rheostat (variable resistor)
or dimmer circuit, even if the rheostat or dimmer channel serves only as a 0 to
100% switch.
Power Linking
The COLORado™ Batten 72 Tour supports power linking for up to 13 other
COLORado™ Batten 72 Tour fixtures at 120 VAC. Each COLORado™ Batten 72 Tour
has Neutrik POWERCON sockets for Power In and Power Out. Although the fixture
comes with a power input cord, it comes with no power linking cord.
AC Plug
The COLORado™ Batten 72 Tour comes with a power input cord terminated with a
NEUTRIK® powerCON A connector on one end and an Edison pl
ug on the other end
(US market). If the power cord that came with your fixture has no plug or you need to
change the Edison plug, use the table below to wire the new plug.
Connection Wire (US) Wire (Europe) Screw Color
AC Live Black Brown Yellow or Brass
AC Neutral White Blue Silver
AC Ground Green/Yellow Green/Yellow Green
Fuse Replacement
1) With a Phillips #2 head screwdriver, unscrew the fuse holder cap from its housing.
2) Remove the blown fuse and replace it with a good fuse of the same type and
rating.
3) Screw the fuse holder cap back in its place and reconnect power.
Make sure to disconnect the fixture’s power cord before replacing™ the blown
fuse, and always replace it with a fuse of the same type and rating.
The fuse is
located inside
this fuse holder

Setup
COLORado™ Batten 72 Tour User Manual Rev. 01d August 23, 2010 -7-
Lens
Replacement
The COLORado™ Batten 72 Tour comes with the 15°lens assembly pre-installed from
the factory. However, there is an optional lens kit (CL20x25x6) available as an
accessory, which will provide a 25º x 6º beam.
Follow the instructions below to to change or replace the LED lenses.
a) Disconnect the fixture from the AC power before opening it.
b) This procedure gives you direct access to the LEDs, which are very fragile.
Use maximum care when handling the lenses over the LED assembly.
The numbers in parenthesis in the procedure below correspond to the parts
indicated in the Exploded View section of the Technical Information chapter.
Procedure
1) Remove the four screws that hold either one of the side covers (10).
2) Remove the side cover.
3) Slide the clear cover (1) out of the way to expose the lens holders (2).
4) Remove the eight screws that hold each of the three lens holders.
5) Remove the lens holders from the fixture.
6) Remove the existing lenses from the lens holders.
7) Insert the new lenses in the lens holders, making sure that you have aligned them
properly.
8) Reverse steps “1” to “5” to complete the lens replacement procedure.
DMX Linking
You may link any COLORado™ Batten 72 Tour fixture to a DMX controller using a
standard DMX serial connection. If using other DMX compatible fixtures with a
COLORado™ Batten 72 Tour fixture, it is possible to control them individually with a
single DMX controller.
If you are not familiar with the DMX standard, or if you need information about the DMX
cables needed to link the COLORado™ Batten 72 Tour fixture to a DMX controller, you
may download the “DMX Primer” document from the CHAUVET® Web site.
The DMX Channel Summary section in this chapter contains a brief description
of what COLORado™ Batten 72 Tour features have a DMX channel assigned to
them. The Operation chapter of this manual provides a detailed list of the
COLORado™ Batten 72 Tour DMX channel assignments.
DMX Modes The COLORado™ Batten 72 Tour uses the standard DMX data connection for its DMX
modes, TOUR, BLOCK1, BLOCK2, ARC1, ARC + D, ARC2, ARC2 + D, ARC + S, and
HSV. You will find information about these DMX modes in the Introduction chapter
(brief description), the Operation Instructions chapter (configuration details), and the
DMX Values section (individual channel values).
Master/Slave
Connectivity
The Master/Slave mode allows a a COLORado™ Batten 72 Tour fixture to control one
or more a COLORado™ Batten 72 Tour fixtures without a DMX controller. The
controlling fixture becomes the “master” when running an Auto program, a Custom
program, or by being in STATIC mode. The controlled fixtures are the “slaves” and you
must set them to “SLAVE” mode from their respective control panels. During the
Master/Slave operation, the slave fixtures will operate in unison with the master fixture.
The master and slave fixtures link to each other using the standard DMX serial
connection. If you are not familiar with the Master/Slave connectivity, you may
download the “DMX Primer” document from the CHAUVET® Web site.
DO NOT connect a DMX controller to the fixtures operating in Master/Slave mode.
Otherwise, the signals from the DMX controller may interfere with the signals from
the master unit.
The Operation chapter of this manual provides detailed instructions on how to
configure the Master and Slave units.

Setup
-8- COLORado™ Batten 72 Tour User Manual Rev. 01d
ID Addressing
The COLORado™ Batten 72 Tour uses the ID Addressing feature to increase the
number of addressable fixtures in the same DMX universe when in the TOUR
personality. Refer to the Operation chapter in this manual to learn in detail how to
configure the COLORado™ Batten 72 Tour fixtures when using ID Addressing. If you
are not familiar with the various connection methods when using ID Addressing, you
may download the “DMX Primer” document from the CHAUVET® Web site.
Mounting
Read the safety notes at the beginning of this guide and follow their recommendations
before mounting this product.
Orientation Always mount this fixture in any safe position while making sure that there is adequate
room around it for ventilation.
Make sure to mount this fixture away from any flammable material as indicated in the
Safety Notes.
Rigging
CHAUVET® recommends following the general guidelines below when mounting the
COLORado™ Batten 72 Tour.
•When selecting an installation location, consider ease of access to the product for
operation, programming adjustments and routine maintenance.
•Always mount this product making sure that there is adequate room around it for
ventilation.
•Do not expose this product to extreme temperature changes, rain, or humidity.
•If mounting this fixture overhead, make sure that the location where you are
mounting it can support its weight. Please see the Technical Specifications section
of this guide for the weight requirement of this product.
Procedure The COLORado™ Batten 72 Tour comes with two adjustable feet that
double as
hanging bracket to which you can attach “C” or “O” clamps. These feet also serve as
floor or wall mount supports. You must supply your own “C” or “O” clamps and make
sure that they are capable
of supporting the weight of this fixture. You will have to use
two mounting points per fixture.
Product Mounting
Diagram
Clamp
(Not
provided)
Clamp
(Not
provided)
Safety
Cable
(Included)
Overhead Mounting
Floor Mounting

Operation
COLORado™ Batten 72 Tour User Manual Rev. 01d August 23, 2010 -9-
4. Operation
Control Panel
Description
Button Function CONTROL PANEL
<MENU> Exits from the current menu or
function
<ENTER> Enables the currently displayed
menu or sets the currently selected
value in to the current function
<UP> Navigates upwards through the
menu list and increases the
numeric value when in a function.
<DOWN> Navigates downwards through the
menu list and decreases the
numeric value when in a function
Control Options
You can set the COLORado™ Batten 72 Tour start address in the 001~512 DMX
range. This allows for the control of up to 39 fixtures in the 13-
channel TOUR
personality. In addition, the ID address system allows you to assign up to 66 fixtures for
each starting DMX address
, thus multiplying the number of fixtures you can control
within a single universe. You can access the fixture’s ID address system from channel
12 when in the TOUR DMX personality.
When programming live performances as well as cues that need to trigger on
demand or on a time line, program no more than 10 fixtures on ID addressing per
DMX channel. This is to remain within a one-second execution time.
Programming
Carry out all the programming procedures indicated below from the control panel. Refer
to the Menu Map on page 14 to learn how the menu options relate to each other.
To go to an option, press <MENU> repeatedly until the option shows on the display.
To select an option value, press <UP> or <DOWN> until you see the desired value and
press <ENTER> to accept it.
To exit to the previous menu level, press <MENU>.
DMX Personality
This setting allows the user to choose a particular DMX personality.
1) Go to PERSON.
2) Select the desired personality (TOUR, BLOCK1, BLOCK2, ARC1, AR1 + D, ARC2,
AR2 + D, AR2 + S, or HSV).
DMX Control
Without ID
Addressing
In this mode, each unit will respond to a unique starting address from the DMX
controller. All units with the same starting address will respond at unison.
1) Select the TOUR personality as shown in DMX Personality.
2) Set the running mode:
a) Go to RUN.
b) Select DMX.
3) Set the starting address:
a) Go to ADDRESS.
b) Select the starting address (001~512).
4) Deactivate ID Addressing in each fixture:
a) Go to SETTINGS.
b) Select ID ON/OFF.
c) Select OFF.
Make sure to deactivate ID Addressing in each fixture when using the TOUR
personality. Otherwise, unintended results may occur if channel 11 is not set to
“0”.
Continues on the next page

Operation
-10- COLORado™ Batten 72 Tour User Manual Rev. 01d
Continued from previous page
DMX Control With ID
Addressing
In this mode, the fixtures with the same DMX starting address will respond to the DMX
controller based on the fixture’s individual ID address setting. If the user selects ID
address “0”, all the fixtures with the same DMX address will respond in unison.
Otherwise, each fixture will follow the control for its particular ID address.
1) Repeat steps 1, 2, and 3from DMX Control Without ID Addressing.
2) Activate ID Addressing in each fixture:
a) Go to SETTINGS.
b) Select ID ON/OFF.
c) Select ON.
Static Color
The Static Color mode allows for permanent RGBWA color mixing without a DMX
controller.
1) Go to STATIC.
2) Select the desired color (RED, GREEN, BLUE, WHITE, or AMBER).
3) Select the desired color value (0~255).
4) Repeat for the other colors.
5) Select STROBE.
6) Select the desired frequency (0~20).
Auto Programs
Auto programs allow for dynamic RGBWA color mixing without a DMX controller.
1) Go to AUTO.
2) Select the desired auto program (AUTO 01~10 or CUSTOM 01~10).
You cannot edit any of the auto programs (AUTO 01~10). However you can edit
custom programs CUSTOM 01~10 (see Edit Customs).
Edit Customs
This setting allows the programming of up to 30 scenes for each of the 10 customizable
programs, including colors and effects.
1) Go to EDIT.
2) Select the desired auto program (CUSTOM 01~10).
3) Select the desired scene (SCENE 01~30).
4) Select the desired color or effect (RED, GREEN, BLUE, WHITE, AMBER,
STROBE, TIME, or FADE).
5) Select the color or effect value (000~255 for colors and timers, or 00~20 for
Strobe).
6) Repeat for the other colors or effects.
7) Return to the SCENE level (step “3”).
8) Repeat for the other scenes.
Master/Slave
The Master/Slave mode allows a group of COLORado™ Batten 72 Tour fixtures (the
slaves) to execute simultaneously the same program, whether auto or custom, that
another COLORado™ Batten 72 Tour fixture (the master) is executing, and without a
DMX controller.
1) Set the Master Unit:
a) Set the running mode to DMX as explained in “DMX Control Without ID
Addressing”
b) Select an Auto program as explained in “Auto Programs”.
2) Set the slave units:
a) Go to RUN.
b) Select SLAVE.
•The fixture that is set to run a program, whether Auto or Custom,
automatically becomes the Master.
•Do not connect a DMX controller to the master or slave fixtures.
Continues on the next page

Operation
COLORado™ Batten 72 Tour User Manual Rev. 01d August 23, 2010 -11-
Continued from previous page
Color Settings The COLOR setting determines how the COLORado™ Batten 72 Tour generates the
white color based on various RGB settings.
1) Go to SETTINGS.
2) Select COLOR.
3) Select OFF, RGB TO W or UC.
OFF = When RGB are all set to “255”, output is maximum.
RGB TO W = When RGB are all set to “255”, output is the defined by the
configured White color (see Whites Setting).
UC = RGB are all set to the produce the same universal color
Dimmer Curves This setting determines the output of the COLORado™ Batten 72 Tour based on the
position of the Red, Green, Blue, White, and Dimmer faders.
1) Go to SETTINGS.
2) Select DIMMER.
3) Select a dimmer curve (OFF, DIM1, DIM2, DIM3, or DIM4).
•When Dim is set to “OFF”, the output is proportional (linear) to the Dimmer
and RGBW channel values.
•When Dim is set to “DIM1” through “DIM4”, the output follows the Dimmer
and RGBW channel values based on the corresponding dimmer curve, being
DIM1 the fastest and DIM4 the slowest.
Control Panel Lock
This setting allows the user to activate or disable the control panel lock, which keeps
non-authorized personnel from changing the fixture’s settings.
1) Go to KEYLOCK.
2) Select ON or OFF.
When the control panel lock is active, the fixture will prompt the user to enter the
password after 30 seconds of control panel inactivity or after turning on the
fixture.
After being prompted to enter the password:
1) Press <UP>, <DOWN>, <UP>, <DOWN>, and <ENTER>
Program Upload
This option allows the user to copy the custom programs of one COLORado™ Batten
72 Tour fixture onto other COLORado™ Batten 72 Tour fixtures by using the
Master/Slave method
1) Configure and connect the fixtures in a Master/Slave arrangement, where the
master unit has the custom programs you want to transfer onto the slave units.
2) At the master unit, go to SETTINGS.
3) Select UPLOAD.
4) When prompted, enter the master access password as shown in Control Panel
Lock.
5) When SEND shows, press <ENTER> to start the upload.
6) Wait for the upload process to finish before disconnecting the fixtures.
•During and after the upload, the master and slave units will visually indicate
the status of the process, as follows:
•Yellow means that the upload is running.
•Red means that the upload failed due to an error.
•Green means that the upload completed successfully.
Continues on the next page

Operation
-12- COLORado™ Batten 72 Tour User Manual Rev. 01d
Continued from previous page
Reset This setting allows the user to reset the COLORado™ Batten 72 Tour fixture to its
default values, including the custom programs.
1) Go to SETTINGS.
2) Select RESET.
3) When prompted, enter the master access password as shown in Control Panel
Lock.
4) Wait for the reset process to finish.
Default Values
Parameter
Default Value
Parameter
Default Value
STATIC 000 DIMMER DIM4
ADDRESS 001 COLOR OFF
RUN
DMX
EDIT
000
PERSON TOUR FANS AUTO
ID
001
KEYLOCK
OFF
ID ON/OFF ON
Whites Setting
This setting allows the user to select and edit the temperature of the white colors used
in channel 7 (Macros) when in the TOUR mode. It also allows the user to define the
maximum RGB values when RGB to White is active.
1) Go to CALIB.
2) Select a white color (WHITE 1~11) or RGB TO W.
3) Select a color (RED, GREEN, BLUE, WHITE, or AMBER).
4) Select a color value (0~255).
5) Repeat for the other colors.
When selecting RGB TO W, you will only be able to define the values of RED,
GREEN, and BLUE.
The values of RED, GREEN, and BLUE configured from CALIB > RGB TO W will
define the color temperature shown when the RGB faders are set to “255” if
COLOR > RGB TO W is active.
Fan Setting 1) Press <MENU> repeatedly until FANS shows, and press <ENTER> to accept.
2) Use <UP>or <DOWN>to select a setting (OFF, LOW, NORMAL, HIGH or AUTO).
3) Press <MENU> to exit once done.
•When in AUTO, the fan speed automatically changes so the fixture’s
temperature does not exceed the limit.
•When in the other settings, the fan speed follow the predefine values.
•The internal controller will override any manual setting if the internal
temperature rises above a certain level.

Operation
COLORado™ Batten 72 Tour User Manual Rev. 01d August 23, 2010 -13-
TOUR Notes
These notes intent to clarify the way the TOUR DMX personality works.
Master Dimmer
•Channel 1 controls the intensity of the currently projected color.
•When the slider is at the highest position (255) the intensity of the output is at its
maximum.
Red, Green, Blue
White, and Amber
Color Selection
•Channels 2, 3, 4, 5, and 6 control the intensity ratio of each of the Red, Green, Blue,
White, and LEDs.
•When the slider is at the highest position (255), the intensity of each color is at its
maximum if SETTINGS > COLOR is OFF.
•You can combine channels, 2, 3, 4, 5, and 6 to create over one trillion colors.
Color Macros
•Channel 7 selects the required Color Macro.
•Channel 7 has priority over channels 2, 3, 4, and 5.
•Channel 1 controls the intensity of the Color Macro.
Strobe •Channel 8 controls the strobe of channels 2~6.
ID Address
Selection
•Channel 12 selects the target ID address.
•Each independent DMX address may have up to 66 independent ID addresses.
•An ID address of 0will activate all ID address locations.
Auto •Channel 9 selects the preset Auto programs AUTO 01~10 or the custom programs
CUSTOM 01~10.
•When activating the custom Auto programs CUSTOM 01~10, it is possible to control
the Step Time and Fade Time using channels 2 and 3 respectively.
•Channel 9 has priority over channels 2, 3, 4, 5, 6, 7, and 8.
Dimmer Speed •Channel 10 is for selecting the dimmer mode and speed. When DIMMER is set to
OFF,RGBW and Master Dimmer are linear. Otherwise, DIM1 is the fastest dimmer
curve, while DIM4 is the slowest.

Operation
-14- COLORado™ Batten 72 Tour User Manual Rev. 01d
Menu Map

Operation
COLORado™ Batten 72 Tour User Manual Rev. 01d August 23, 2010 -15-
DMX Values
TOUR
Channel Function Value Percent/Setting
1
Dimmer
000

255
0~100%
2
Red
000

255
0~100% (or Step Time if Custom 01~10 in Ch. 9 is active)
3
Green
000

255
0~100% (or Fade Time if Custom 01~10 in Ch. 9 is active)
4
Blue
000 255 0~100%
5
White
000

255
0~100%
6
Amber 000255 0~100%
7 Color Macro +
White Balance
000 010
011 030
031 050
051 070
071 090
091 110
111 130
131 150
151 170
171 200
201 205
206 210
211 215
216 220
221 225
226 230
231 235
236 240
241 245
246 250
251 255
No function
R: 100% / G: Up / B: 0%
R: Down / G: 100% / B: 0%
R: 0% / G: 100% / B: Up
R: 0% / G: Down / B: 100%
R: Up / G: 0% / B: 100%
R: 100% / G: 0% / B: Down
R: 100% / G: Up / B: Up
R: Down / G: Down / B: 100%
R: 100% / G: 100% / B: 100% / W: 100%
White 1: 3200 K
White 2: 3400 K
White 3: 4200 K
White 4: 4900 K
White 5: 5600 K
White 6: 5900 K
White 7: 6500 K
White 8: 7200 K
White 9: 8000 K
White 10: 8500 K
White 11: 10,000 K
8 Strobe 000 009
010 255 No function 1~20 Hz
9 Auto + Custom Programs +
Fan Control
000 010
011 020
021 030
031 040
041 050
051 060
061 070
071 080
081 090
091 100
101 110
111 120
121 130
131 140
141 150
151 160
161 170
171 180
181 190
191 200
201 210
211 220
221 230
231 240
241 250
251 255
No function
Fans Off (Stay 3 s)
Fans Low (Stay 3 s)
Fans High (Stay 3 s)
Fans Normal (Stay 3 s)
Fans Auto (Stay 3 s)
Auto 1
Auto 2
Auto 3
Auto 4
Auto 5
Auto 6
Auto 7
Auto 8
Auto 9
Auto 10
Custom 1
Custom 2
Custom 3
Custom 4
Custom 5
Custom 6
Custom 7
Custom 8
Custom 9
Custom 10
10
Auto Speed
000

255
0~100%
11 Dimmer Speed
000

009
010 029
030 069
070 129
130 189
190

255
Dimmer speed as per Control Panel
Linear dimmer
Non-linear dimmer 1 (fastest)
Non-linear dimmer 2
Non-linear dimmer 3
Non-linear dimmer 4 (slowest)
Continues on the next page

Operation
-16- COLORado™ Batten 72 Tour User Manual Rev. 01d
Continued from previous page
TOUR (Cont.)
Channel Function Value Setting Value Setting Value Setting
12 ID Address
000

009
010 019
020 029
030 039
040 049
050 059
060 069
070 079
080 089
090 099
100 109
110 119
120 129
130 139
140 149
150 159
160 169
170 179
180 189
190 199
200 209
210
211
All IDs
ID 1
ID 2
ID 3
ID 4
ID 5
ID 6
ID 7
ID 8
ID 9
ID 10
ID 11
ID 12
ID 13
ID 14
ID 15
ID 16
ID 17
ID 18
ID 19
ID 20
ID 21
ID 22
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
ID 23
ID 24
ID 25
ID 26
ID 27
ID 28
ID 29
ID 30
ID 31
ID 32
ID 33
ID 34
ID 35
ID 36
ID 37
ID 38
ID 39
ID 40
ID 41
ID 42
ID 43
ID 44
ID 45
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
ID 46
ID 47
ID 48
ID 49
ID 50
ID 51
ID 52
ID 53
ID 54
ID 55
ID 56
ID 57
ID 58
ID 59
ID 60
ID 61
ID 62
ID 63
ID 64
ID 65
ID 66
13 Block Selection
000 004
005 034
035 064
065 094
095 124
125 154
155 184
185 214
215

255
Blocks 1, 2 & 3
Block 1
Block 2
Block 3
Blocks 1 & 2
Blocks 2 & 3
Blocks 1 & 3
Blocks 1, 2 & 3
No Function
BLOCK1
Channel Function Value Percent/Setting
1
Block 1 - Red
000

255
0~100%
2
Block 1 - Green
000

255
0~100%
3
Block 1 - Blue
000

255
0~100%
4
Block 2 - Red
000 255 0~100%
5
Block 2 - Green
000 255 0~100%
6
Block 2 - Blue
000

255
0~100%
7
Block 3 - Red 000255 0~100%
8
Block 3 - Green 000255 0~100%
9
Block 3 - Blue
000

255
0~100%
BLOCK2 Channel Function Value Percent/Setting
1
Block 1 - Red
000

255
0~100%
2
Block 1 - Green 000 255 0~100%
3
Block 1 - Blue 000 255 0~100%
4
Block 1 – White 000 255 0~100%
5
Block 1 - Amber
000

255
0~100%
6
Block 2 - Red
000

255
0~100%
7
Block 2 - Green
000

255
0~100%
8
Block 2 - Blue
000

255
0~100%
9
Block 2 – White
000

255
0~100%
10
Block 2 - Amber
000

255
0~100%
11
Block 3 - Red
000

255
0~100%
12
Block 3 - Green
000

255
0~100%
13
Block 3 - Blue
000

255
0~100%
14
Block 3 - White 000255 0~100%
15
Block 3 - Amber
000

255
0~100%
Continues on the next page