Chauvet GigBar LT User manual

User Manual

Page 2 of 21 GigBAR LT User Manual Rev. 1
TABLE OF CONTENTS
1. Before You Begin.......................................................................................................... 3
What Is Included .............................................................................................................................3
Unpacking Instructions....................................................................................................................3
Claims..................................................................................................................................................... 3
Text Conventions ............................................................................................................................3
Symbols ..........................................................................................................................................3
Disclaimer .......................................................................................................................................3
Product at a Glance ........................................................................................................................4
Safety Notes....................................................................................................................................4
2. Introduction................................................................................................................... 5
Product Overview............................................................................................................................5
Product Dimensions........................................................................................................................6
3. Setup.............................................................................................................................. 7
AC Power........................................................................................................................................7
Fuse Replacement..........................................................................................................................7
Power Linking......................................................................................................................................... 7
Mounting .........................................................................................................................................8
Orientation.............................................................................................................................................. 8
Rigging ................................................................................................................................................... 8
4. Operation....................................................................................................................... 9
Control Panel Operation..................................................................................................................9
Menu Map .......................................................................................................................................9
DMX Linking..................................................................................................................................10
Configuration (DMX)............................................................................................................................. 10
DMX Personality and Starting Address................................................................................................. 10
DMX Channel Assignments and Values.......................................................................................10
17CH .................................................................................................................................................... 10
17CH (cont.)......................................................................................................................................... 11
06CH .................................................................................................................................................... 12
03CH .................................................................................................................................................... 12
Configuration (Standalone)...........................................................................................................13
Auto Mixed Effects................................................................................................................................ 13
Sound-Active Mixed Effects.................................................................................................................. 13
Show Mode........................................................................................................................................... 13
Color Mixing.......................................................................................................................................... 14
Rearranging the Fixtures...................................................................................................................... 14
Factory Reset....................................................................................................................................... 14
Master/Slave Mode.......................................................................................................................14
Footswitch Operation....................................................................................................................15
IRC-6 Infrared Remote Control.....................................................................................................16
IRC-6 Operation.................................................................................................................................... 16
5. Maintenance .................................................................................................................17
Product Maintenance....................................................................................................................17
6. Technical Specifications..............................................................................................18
Returns .............................................................................................................................20
Contact Us .........................................................................................................................21

GigBAR LT User Manual Rev. 1 Page 3 of 21
1.BEFORE YOU BEGIN
What Is
Included
•GigBAR LT
•Power Cord
•Carrying Cases
•Tripod
•Footswitch
•Warranty Card
•Quick Reference Guide
•IRC-6 Remote
Unpacking
Instructions
Carefully unpack the product immediately and check the container to make sure all the
parts are in the package and are in good condition.
Claims
If the box or the contents (the product and included accessories) ap
pear damaged from
shipping, or show signs of mishandling, notify the carrier immediately, not Chauvet.
Failure to report damage to the carrier immediately may invalidate your claim. In
addition, keep the box and contents for inspection.
For other issues, s
uch as missing components or parts, damage not related to shipping,
or concealed damage, file a claim with Chauvet within 7 days of delivery.
Text
Conventions
Convention
Meaning
1—512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Symbol
Meaning
Electrical warning. Not following these instructions may cause
electrical damage to the product, accessories, or the user.
Critical installation, configuration, or operation information. Not
following these instructions may make the product not work, cause
damage to the product, or cause harm to the operator.
Important installation or configuration information. The product
may not function correctly if this information is not used.
Useful information.
Disclaimer
Chauvet believes that the information cont
ained in this manual is accurate in all
respects. However, Chauvet assumes no responsibility and specifically disclaims any
and all liability to any party for any loss, damage or disruption caused by any errors or
omissions in this document, whether such errors or omissions result from negligence,
accident or any other cause. Chauvet reserves the right to revise the content of this
document without any obligation to notify any person or company of such revision,
however, Chauvet has no obligation to make, and does not commit to make, any such
revisions. Download the latest version from www.chauvetlighting.com.
The works of authorship contained in this manual, including, but notlimited to, alldesign,
text and images are owned by Chauvet.
©Copyright 2016Chauvet & Sons, LLC.All rights reserved.
Electronically published by Chauvet in the United States of America.
CHAUVET, the Chauvet logo, and GigBAR LT are registered trademarks or
trademarks of Chauvet & Sons LLC (d/b/a Chauvet and Chauvet Lighting) in the
United States and other countries. Other company and product names and logos
referred to herein may be trademarks of their respective companies.

Page 4 of 21 GigBAR LT User Manual Rev. 1
Product at a
Glance
Use on Dimmer
x
Auto Programs
P
Outdoor Use
x
Auto-ranging Power Supply
P
Sound-Active
P
Replaceable Fuse
P
DMX
P
User-Serviceable
x
Master/Slave
P
Safety Notes
Please read the following Safety Notes carefully before working with the product. The
Notes include important safety information about installation, usage, and maintenance.
•Always connect the product to a grounded circuit to avoid the risk of electrocution.
•Always disconnect the product from the power source before cleaning or replacing
the fuse.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power cord by pulling or tugging on the cord.
•If mounting the product overhead, always secure to a fastening device using a
safety cable.
•Make sure there are no flammable materials close to the product when operating.
•Do not touch the product’s housing when operating because it may be very hot.
•The product is not intended for permanent installation.
•Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
•The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
•Always install the product in a location with adequate ventilation, at least 20 in
(50 cm) from adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Never connect the product to a dimmer.
•Make sure to replace the fuse with another of the same type and rating.
•Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket.
•The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the
product at higher temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center.
•To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
Keep this User Manual for future use. If you sell the product to someone else, be
sure that they also receive this document.

GigBAR LT User Manual Rev. 1 Page 5 of 21
2.INTRODUCTION
Product Overview
Power In
Sound Sensitivity
Knob
Fuse Holder
IR Sensor
DMX
In/Out
Strobe LEDs
Safety Loop
LED
Display
Menu
Buttons
Power Out
Back Panel View
Front View
IR Sensor
Microphone
Footswitch
Plug
Pars
Moonflowers

Page 6 of 21 GigBAR LT User Manual Rev. 1
Product Dimensions
12.9 in
330 mm
41.1 in
1,045 mm
5.3 in
135 mm

GigBAR LT User Manual Rev. 1 Page 7 of 21
3.SETUP
AC Power
The GigBAR LT has an auto-
ranging power supply and it can work with an input voltage
range of 100 to 240 VAC, 50/60 Hz. To determine the product’s
power requirements
(circuit breaker, power outlet, and wiring), use the current value listed on
the label
affixed to the product’s back panel, or refer to the product
’s specifications chart. The
listed current rating indicates the product
’s average current draw under normal
conditions.
•Always connect the product to a protected circuit (circuit breaker or fuse).
Make sure the product has an appropriate electrical ground to avoid the risk
of electrocution or fire.
•To eliminate unnecessary wear and improve its lifespan, during periods of
non-use completely disconnect the product from power via breaker or by
unplugging it.
Never connect the product
to a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Fuse
Replacement
1. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
2. Pry the fuse holder out of the housing.
3. Remove the blown fuse from the holder and replace with a fuse of the exact same
type and rating.
4. Insert the fuse holder back in place and reconnect power.
Disconnect the product from the power outlet before replacing the fuse.
Power Linking The product provides power linking via the Edison
outlet located in the back of the
product. Please see the diagram below for further explanation.
Power Linking
Diagram
You can power link up to 11 GigBAR LT products on 120 VAC or up to 20
GigBAR LT products on 230 VAC.
The power linking diagram corresponds to the North American version of the
product ONLY! If using the product in other markets, you must consu
lt with the
local Chauvet
distributor as power linking connectors and requirements may
differ in your country or region.
1st Product
2nd Product
3rd Product
Additional
Products
Installed fuse
(held by plastic clip)
Spare fuse holder
(inside safety cap)
Safety cap

Page 8 of 21 GigBAR LT User Manual Rev. 1
Mounting
Before mounting the product
, read and follow the safety recommendations indicated in
the Safety Notes.
Orientation
The GigBAR LT
may be mounted in any position; however, make sure adequate
ventilation is provided around the product.
Rigging
•Before deciding on a location for the product, always make sure there is easy
access to the product for maintenance and programming purposes.
•Make sure that the structure onto which you are mounting the product can support
the product’s weight. See the Technical Specifications for weight information.
•When mounting the product overhead, always use a safety cable. Mount the
product securely to a rigging point, whether an elevated platform or a truss.
•When rigging the product onto a truss, use a mounting clamp of appropriate weight
capacity.
•When power linking multiple products, mount the products close enough for power
linking cables to reach.
•The bracket adjustment knobs allow for directional adjustment when aiming the
product to the desired angle. Only loosen or tighten the bracket knobs manually.
Using tools could damage the knobs.
Mounting Diagram
Additional Product
Mounting Knobs
Pod Tilt Adjustment Knob
Safety Cable
Tripod Insertion Point
Pod Pan Adjustment Knob

GigBAR LT User Manual Rev. 1 Page 9 of 21
4.OPERATION
Control Panel
Operation
To access the control panel functions, use the four buttons located underneath the
display. Please refer to the Product Overviewto see the button locations
on the control
panel.
Button
Function
<MENU>
Press to find an operation mode or to back out of the current menu
option
<UP>
Press to scroll up the list of options or to find a higher value
<DOWN>
Press to scroll down the list of options or to find a lower value
<ENTER>
Press to activate a menu option or a selected value
Menu Map
Main Level
Programming Levels
Description
Aut_
Aut1
F 01–F 99
Auto mixed effect 1 (speed)
Aut2
Auto mixed effect 2 (speed)
Sud_
Sud1
Sound-Active mixed effect 1
Sud2
Sound-Active mixed effect 2
ShoW
AP-- AP01–AP07
F 01–F 99
Auto Par programs (speed)
AM01
F 01–F 99
Auto Moonflower programs (speed)
AS--
AS01–AS10
F 01–F 99
Auto Strobe programs (speed)
APM- APM1–APM4
F 01–F 99
Auto Par + Moonflower programs (speed)
APS1
F 01–F 99
Auto Par + Strobe programs (speed)
AMS1 F 01–F 99
Auto Moonflower + Strobe programs
(speed)
SP--
SP01–SP07
Sound-Active par programs
SM01
Sound-Active Moonflower program
SS--
SS01–SS10
Sound-Active Strobe programs
SPM-
SPM1–SPM4
Sound-Active Par + Moonflower programs
SPS1
Sound-Active Par + Strobe program
SMS1
Sound-Active Moonflower + Strobe program
CoLo
r000–r255
g000–g255
b000–b255
Custom mix colors (red, green, and blue)
d_ _ _
17CH d001–d496
Sets 17-channel DMX personality and
address
06CH d001–d507
Sets 6-channel DMX personality and
address
03CH d001–d510 Sets 3-channel DMX personality and
address
SLAV
SLAV
Slave mode
SYS dSEt 1234
Rearrange fixtures (see Rearranging the
Fixtures for more information)
rSEt
Resets to factory defaults

Page 10 of 21 GigBAR LT User Manual Rev. 1
DMX Linking
The GigBAR LT works with a DMX controller. Information about DMX is in the CHAUVET
DMX Primer, which is available from the Chauvet website
http://www.chauvetlighting.com/downloads/DMX_Primer_rev05_WO.pdf.
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
DMX Personality
and
Starting
Address
When selecting a starting DMX address, always consider the numb
er of DMX channels
the selected DMX mode uses. If you choose a starting address that is too high, you
could restrict the access to some of the product’s channels.
The GigBAR LT uses up to 17 DMX channels in a 17-channel
DMX mode, which defines
the highest configurable address to 496.
If you are not familiar with the DMX protocol, download the DMX Primer from
www.chauvetlighting.com.
To select the starting address, do the following:
1. Press <MENU> repeatedly until d_ _ _ shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select 17CH, 06CH, or 03CH.
4. Press <ENTER>, and d 1–d496 (for 17CH), d 1–d507 (for 06CH), or d 1–d510
(for 03CH) will show on the display.
5. Use <UP> or <DOWN> to select the starting address.
6. Press <ENTER>.
DMX Channel Assignments and Values
17CH
Channel
Function
Value
Percent/Setting
1
Par 1 Red
000
ó
255
0–100%
2
Par 1 Green
000ó255 0–100%
3
Par 1 Blue
000
ó
255
0–100%
4 Par 1 Shutter
000
ó
127
Dimmer 0–100%
128ó239 Strobe, slow to fast
240
ó
249
Sound-activated strobe
250
ó
255
Full on
5
Par 2 Red
000ó255 0–100%
6
Par 2 Green
000ó255
0–100%
7
Par 2 Blue
000
ó
255
0–100%
8 Par 2 Shutter
000ó127 Dimmer 0–100%
128
ó
239
Strobe, slow to fast
240
ó
249
Sound-activated strobe
250
ó
255
Full on
9 Moonflower 1
Color
000
ó
024
No function
025ó049
Red
050
ó
074
Green
075
ó
099
Blue
100
ó
124
Red + green
125
ó
149
Red + blue
150ó174 Green + blue
175
ó
199
Red + green + blue
200
ó
224
Auto single color loop
225
ó
255
Auto two color loop

GigBAR LT User Manual Rev. 1 Page 11 of 21
17CH
(cont.)
Channel
Function
Value
Percent/Setting
10
Moonflower 1
Strobe (When CH9 is
025ó199)
000
ó
009
No function
010ó239 Strobe, slow to fast
240
ó
255
Sound-activated strobe
Moonflower 1
Auto Speed (When
CH9 is 200ó255)
000ó239 Auto speed, slow to fast
240
ó
255
Sound-activated mode
11 Moonflower 1
Rotation
000
ó
004
Stop
005
ó
127
Rotate clockwise, slow to fast
128
ó
133
Stop
134
ó
255
Rotate counter-clockwise, slow to fast
12 Moonflower 2
Color
000ó024 No function
025
ó
049
Red
050
ó
074
Green
075
ó
099
Blue
100
ó
124
Red + green
125ó149 Red + blue
150
ó
174
Green + blue
175
ó
199
Red + green + blue
200
ó
224
Auto single color loop
225
ó
255
Auto two color loop
13
Moonflower 2
Strobe (When CH12
is 025ó199)
000ó009 No function
010
ó
239
Strobe, slow to fast
240
ó
255
Sound-activated strobe
Moonflower 2
Auto Speed (When
CH12 is 200
ó
255)
000ó239 Auto speed, slow to fast
240ó255 Sound-activated mode
14 Moonflower 2
Rotation
000
ó
004
Stop
005
ó
127
Rotate clockwise, slow to fast
128
ó
133
Stop
134ó255 Rotate counter-clockwise, slow to fast
15 Strobe Program
000
ó
009
All on (CH16 must be active)
010
ó
029
Auto program 1
030
ó
049
Auto program 2
050
ó
069
Auto program 3
070ó089 Auto program 4
090
ó
109
Auto program 5
110
ó
129
Auto program 6
130
ó
149
Auto program 7
150
ó
169
Auto program 8
170ó189 Auto program 9
190
ó
209
All strobing
210
ó
255
Sound-activated strobe
16
Strobe Dimmer
000ó255 0–100%
17
Strobe Speed
000ó255 Strobe speed, slow to fast

Page 12 of 21 GigBAR LT User Manual Rev. 1
06CH
Channel
Function
Value
Percent/Setting
1
Red
000
ó
255
0–100%
2
Green
000ó255 0–100%
3
Blue
000ó255 0–100%
4 Shutter
000
ó
127
Dimmer 0–100%
128
ó
239
Strobe, slow to fast
240
ó
249
Sound-activated strobe
250
ó
255
Full on
5 Moonflower Rotation
000ó004 Stop
005
ó
127
Rotate clockwise, slow to fast
128
ó
133
Stop
134
ó
255
Rotate counter-clockwise, slow to fast
6 Strobe
000
ó
054
Strobe dimmer 0–100%
055ó249 Strobe speed slow to fast
03CH
Channel
Function
Value
Percent/Setting
1 Auto/Sound
Programs
000
ó
009
No function
010
ó
119
Auto mixed effect 1, slow to fast
120ó229 Auto mixed effect 2, slow to fast
230
ó
234
Sound-activated mixed effect 1
235
ó
239
Sound-activated mixed effect 2
240ó255 Show mode (CH2 must be active)
2 Show Mode
(CH1 must be
240ó255)
000
ó
009
No function
010ó029 Pars
030
ó
049
Moonflowers
050
ó
069
Strobes
070ó089 Pars + Moonflowers
090
ó
109
Pars + Strobes
110
ó
129
Moonflowers + Strobes
130
ó
149
Sound-Active Pars
150
ó
169
Sound-Active Moonflowers
170
ó
189
Sound-Active Strobes
190
ó
209
Sound-Active Pars + Moonflowers
210ó229 Sound-Active Pars + Strobes
230
ó
255
Sound-Active Moonflowers + Strobes
3
Show Mode Speed
000ó255 CH2 program speed, slow to fast

GigBAR LT User Manual Rev. 1 Page 13 of 21
Configuration
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
•Connect the product to a suitable power outlet.
Never connect a product that is operating in any standalone mode
to a DMX string
connected to a DMX controller. Product
s in standalone mode may transmit DMX
signals that could interfere with the DMX signals from the controller.
Auto Mixed
Effects
To run the GigBAR LT in one of the Auto mixed effects, follow the instructions below:
1. Press <MENU> repeatedly until Aut_ shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select Aut1 or Aut2.
4. Press <ENTER>. F 01–F 99 will show on the display.
5. Use <UP> or <DOWN> to increase or decrease the program speed.
Sound-
Active
Mixed Effects
To run the GigBAR LT in one of the Sound-Active mixed effects, do the following:
1. Press <MENU> repeatedly until Sud_ shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select Sud1 or Sud2.
4. Press <ENTER>.
5. Turn the Sound Sensitivity Knob up until the product responds to the beat of the
music. See the Product Overview for more information.
The product will only respond to low frequencies of music (bass and drums).
Show Mode
To run the product in Show Mode, follow the instructions below:
1. Press <MENU> repeatedly until ShoW shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select:
•AP-- (Auto Pars)
•AM01 (Auto Moonflowers)
•AS-- (Auto Strobes)
•APM-(Auto Pars and Moonflowers)
•APS1 (Auto Pars and Strobes)
•AMS1 (Auto Moonflowers and Strobes)
•SP-- (Sound-Active Pars)
•SM01 (Sound-Active Moonflowers)
•SS-- (Sound-Active Strobes)
•SPM- (Sound-Active Pars and Moonflowers)
•SPS1 (Sound-Active Pars and Strobes)
or
•SMS1 (Sound-Active Moonflowers and Strobes)
4. Press <ENTER>.
5. For:
•AP--, use <UP> or <DOWN> to select AP01–AP07.
•AS--, use <UP> or <DOWN> to select AS01–AS10.
•APM-, use <UP> or <DOWN> to select APM1–APM4.
•SP--, use <UP> or <DOWN> to select SP01–SP07.
•SS--, use <UP> or <DOWN> to select SS01–SS10.
or
•SPM-, use <UP> or <DOWN> to select SPM1–SPM4.
For AM01, APS1, or AMS1, F 01–F 99 will show on the display. Use <UP> or
<DOWN> to increase or decrease the program speed.
6. Press <ENTER>.
7. For AP--, AS--, or APM-, F 01–F 99 will show on the display. Use <UP> or
<DOWN> to increase or decrease the program speed.

Page 14 of 21 GigBAR LT User Manual Rev. 1
Color Mixing
To custom mix a color, do the following:
1. Press <MENU> repeatedly until CoLo shows on the display.
2. Press <ENTER> and one of the following will show on the display:
•r_ _ _ (red)
•g_ _ _ (green)
•b_ _ _ (blue)
3. Press <ENTER> to cycle through the color settings.
4. When the desired color shows on the display, use <UP> or <DOWN> to increase or
decrease the color value.
5. Repeat steps 3 and 4 until the product outputs as desired.
After setting the blue color value, pressing <ENTER> will cause CoLo to show on
the display. Press <ENTER> to cycle through the colors again.
Rearranging the
Fixtures
To rearrange the location of each fixture on the GigBAR LT, follow the instructions below:
1. Press <MENU> repeatedly until SYS shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select dSEt.
4. Press <ENTER>.
5. Press <UP> to select which fixture to rearrange.
6. Press <DOWN> to change the address.
7. Repeat steps 5-6 until all fixtures are addressed correctly.
8. Press <ENTER>.
Factory Reset
To reset the product to factory defaults, do the following:
1. Press <MENU> repeatedly until SYS shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select rSEt.
4. Press <ENTER>.
Master/Slave
Mode
The Master/Slave mode allows a single GigBAR LT product (the master) to control the
actions of one or more GigBAR LT products (the slaves) without the need of a DMX
controller. The master product will be set to operate in either Stand-
Alone mode or with
the IRC-
6, while the slave products will be set to operate in Slave mode. Once set and
connected, the slave products will operate in unison with the master product.
Configure the products as indicated below.
Slave products:
1. Press <MENU> repeatedly until SLAV shows on the display.
2. Press <ENTER> to accept.
Master product:
1. Set the master product in Stand-Alone mode or with the IRC-6.
2. Make the master product the first product in the DMX daisy chain.
•Configure all the slave products before connecting the master to the daisy
chain.
•Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller may interfere with the signals from the
master.
•Do not connect more than 31 slaves to the master.

GigBAR LT User Manual Rev. 1 Page 15 of 21
Footswitch Operation
The included footswitch provides quick access to preset colors, color-
change programs,
and sound-activation through the GigBAR LT microphone.
To use the Footswitch:
1. Connect the GigBAR LT to power.
2. Navigate to Auto or Sound mode.
3. Plug the footswitch cable into the Footswitch Plug on the product (see the Product
Overview).
4. Press any pedal to activate footswitch control.
Pedal
Sub-option
Function
1
(Auto)
1
st
press
Aut1
- Auto mixed effect 1
2nd press
Aut2 - Auto mixed effect 2
3rd press
Show - Auto par effect 1
4th press
Show - Auto par effect 2
5th press
Show - Auto moonflower effect
6th press
Show - Auto par and moonflower effect 1
7th press
Show - Auto par and moonflower effect 2
8
th
press
Show - Auto par and moonflower effect 3
9th press
Show - Auto par and strobe effect
10th press
Show - Auto moonflower and strobe effect
2
(Sound)
1
st
press
Sud1
- Sound-active mixed effect 1
2nd press
Sud2 - Sound-active mixed effect 2
3rd press
Show - Sound-active par effect 1
4th press
Show - Sound-active par effect 2
5th press
Show - Sound-active moonflower effect
6th press
Show - Sound-active par and moonflower effect 1
7th press
Show - Sound-active par and moonflower effect 2
8
th
press
Show - Sound-active par and moonflower effect 3
9th press
Show - Sound-active par and strobe effect
10th press
Show - Sound-active moonflower and strobe effect
3
(Color)
1
st
press Red
2nd press
Green
3rd press
Blue
4th press
Yellow (red and green)
5th press
Cyan (green and blue)
6th press
Purple (red and blue)
7th press
White (red, green, and blue)
4
(Blackout)
N/A Toggles Black Out (turns all lights off)
1
2
3
4

Page 16 of 21 GigBAR LT User Manual Rev. 1
IRC-6 Infrared
Remote
Control
The GigBAR LT is compatible with the IRC-6 infrared remote control from Chauvet. To
activate IR mode, press any button on the IRC-6.
Be sure the IRC-
6 remote is pointing directly at the product and there is nothing in
between the remote and the product.
IRC-6 Operation
Auto Mode
To run the product on an auto program:
1. Press <AUTO> on the IRC-6.
2. Press <0> – <9> to select an automatic program.
3. Use <+> or <-> to increase or decrease the program speed.
Sound-Active Mode
To run the product on a Sound-Active program:
1. Press <SOUND> on the IRC-6.
2. Press <0> – <9> to select a Sound-Active program.
Strobe Modes
To run the strobes on a separate program from the other fixtures:
1. Set the mode for the rest of the product’s fixtures
2. Press <STROBE>on the IRC-6.
3. Press <0> – <9> to select a strobe program.
4. Use <+> or <-> to increase or decrease the program speed.
GigBAR LT IRC-6 Buttons:
Auto Mode / Sound-Active Mode
Strobe Modes
<0> - Mixed effect 1 (default)
<0> - Strobe all (default)
<1> - Mixed effect 2
<1> - Strobe Auto 1
<2> - Par 1
<2> - Strobe Auto 2
<3> - Par 2
<3> - Strobe Auto 3
<4> - Moonflower
<4> - Strobe Auto 4
<5> - Par + Moonflower 1
<5> - Strobe Auto 5
<6> - Par + Moonflower 2
<6> - Strobe Auto 6
<7> - Par + Moonflower 3
<7> - Strobe Auto 7
<8> - Par + Strobe
<8> - Strobe Auto 8
<9> - Moonflower + Strobe
<9> - Strobe Auto 9
Fade Mode
To set the Pars and Moonflowers to fade from color to color, press <FADE>
on the
IRC-6.
Manual Color Control
To manually select a color for the Pars and Moonflowers, press:
•<R> - for Red
•<G> - for Green
•<B> - for Blue
•<A> - for Yellow (Red and Green)
•<UV> - for Purple (Red and Blue)
or
•<W> - for White (Red, Green, and Blue)
Black Out
To black out the light:
Press <BLACK OUT> on the IRC-6.
This will turn off the light until the button is pressed again.
NOTE
: The IRC will not respond to any inputs when Black Out is activated. If the remote
does not respond when a button is pressed, try pressing <BLACK OUT>. You may have
inadvertently activated Black Out.
All other buttons on the IRC-
6 infrared remote control have no function with this
product.

GigBAR LT User Manual Rev. 1 Page 17 of 21
5.MAINTENANCE
Product
Maintenance
Dust build-
up reduces light output performance and can cause overheating. This can
lead to reduction of the light source’s life and/or
mechanical wear. To maintain optimum
performance and minimize wear, clean your lighting product
s at least twice a month.
However, be aware that usage and environmental conditions could be contributing
factors to increase the cleaning frequency.
To clean the product, follow the instructions below:
1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external surface/vents.
4. Clean all transparent surfaces with a mild soap solution, ammonia-free glass
cleaner, or isopropyl alcohol.
5. Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning tissue.
6. Softly drag any dirt or grime to the outside of the transparent surface.
7. Gently polish the transparent surfaces until they are free of haze and lint.
Always dry the transparent surfaces carefully after cleaning them.

Page 18 of 21 GigBAR LT User Manual Rev. 1
6.TECHNICAL SPECIFICATIONS
Dimensions and
Weight
GigBAR LT
Length
Width
Height
Weight
41.1 in (1045 mm)
12.9 in (330 mm)
5.3 in (135 mm)
12 lb (5.5 kg)
Tripod
Max Height
Outer Pipe Diameter
Inner Pipe Diameter
Leg Width (Footprint)
84 in (2134 mm)
1.5 in (38 mm)
1.4 in (35 mm)
40 in (1016 mm)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100 to 240 VAC, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
47 W
43 W
Operating Current
0.7 A
0.4 A
Power linking current
(products)
8 A (11 products) 8 A (20 products)
Fuse
F 1.6 A, 250 V
F 1.6 A, 250 V
Power I/O
U.S./Worldwide
UK/Europe
Power input connector
IEC
IEC
Power output connector
Edison
IEC
Power Cord plug
Edison (U.S.)
Local plug
Light Source
Pars
Type
Power
Lifespan
LED
2.6 W
50,000 hours
Color
Quantity
Current
Tri-color RGB
6
1.4 A
Moonflowers
Type
Power
Lifespan
LED
5.4 W
50,000 hours
Color
Quantity
Current
Tri-color RGB
2
1.8 A
Strobes
Type
Power
Lifespan
LED
1.2 W
50,000 hours
Color
Quantity
Current
White
4
356 mA

GigBAR LT User Manual Rev. 1 Page 19 of 21
Photometrics
Parameter
Value
Strobe Rate (Pars)
0 to 8.2 Hz
Strobe Rate (Moonflowers)
0 to 8.2 Hz
Strobe Rate (Strobes)
0 to 13.2 Hz
Beam Angle (Pars)
13°
Field Angle (Pars)
27°
Illuminance @ 2 m (Pars)
1,609 lux (per pod)
Thermal
Maximum External Temp.
Cooling System
104 °F (40 °C)
Convection
DMX
I/O Connectors
Channel Range
3-pin XLR
3, 6 or 17
Ordering
Product Name
Item Code
UPC Number
GigBAR LT
10031089
781462214388

Page 20 of 21 GigBAR LT User Manual Rev. 1
R
ETURNS
In case you need to get support or return a product:
•If you are located in the U.S., contact Chauvet World Headquarters.
•If you are located in the UK or Ireland, contact Chauvet Europe Ltd.
•If you are located in Mexico, contact Chauvet Mexico.
•If you are located in Benelux, contact Chauvet Europe BVBA.
•If you are located in any other country, DO NOT contact Chauvet. Instead, contact
your local distributor. See www.chauvetlighting.com for distributors outside the U.S.,
UK, Ireland, Mexico, or Benelux.
If you are located outside the U.S., UK, Ireland, Mexico, or Benelux, contact your
distributor of record and follow
their instructions on how to return Chauvet
products to them. Visit our website www.chauvetlighting.com for contact details.
Call the corresponding Chauvet Technical Support office and request a Return
Merc
handise Authorization (RMA) number before shipping the product. Be prepared to
provide the model number, serial number, and a brief description of the cause for the
return.
Send the merchandise prepaid, in its original box, and with its original packing and
accessories. Chauvet will not issue call tags.
Clearly label the package with the RMA number. Chauvet will refuse any product
returned without an RMA number.
Write the RMA number on a properly affixed label. DO NOT write the RMA number
directly on the box.
Before sending the product, clearly write the following information on a piece of paper
and place it inside the box:
•Your name
•Your address
•Your phone number
•RMA number
•A brief description of the problem
Be sure to pack the product properly. Any sh
ipping damage resulting from inadequate
packaging will be your responsibility. FedEx packing or double-
boxing are
recommended.
Chauvet reserves the right to use its own discretion to repair or replace returned
product(s).