Chauvet Gobo Zoom LED 2.0 User manual

User Manual

Page 2 of 12 Gobo Zoom LED 2.0 (Rev. 3)
TABLE OF CONTENTS
1. BEFORE YOU BEGIN....................................................................................................................................................... 3
WHAT IS INCLUDED................................................................................................................................................................................3
UNPACKING INSTRUCTIONS....................................................................................................................................................................3
CLAIMS ................................................................................................................................................................................................3
MANUAL CONVENTIONS.........................................................................................................................................................................3
ICONS ..................................................................................................................................................................................................3
SAFETY INSTRUCTIONS..........................................................................................................................................................................4
2. INTRODUCTION ............................................................................................................................................................... 5
PRODUCT OVERVIEW ............................................................................................................................................................................5
3. SETUP............................................................................................................................................................................... 6
ACPOWER...........................................................................................................................................................................................6
REPLACING THE GOBO/COLOR GEL........................................................................................................................................................6
MOUNTING ...........................................................................................................................................................................................7
Orientation................................................................................................................................................................................................................7
Rigging.....................................................................................................................................................................................................................7
4. OPERATING INSTRUCTIONS.......................................................................................................................................... 8
CONFIGURING THE STARTING ADDRESS..................................................................................................................................................8
DMX Operation........................................................................................................................................................................................................8
Standalone...............................................................................................................................................................................................................8
DMXCHANNEL VALUES........................................................................................................................................................................8
5. APPENDIX......................................................................................................................................................................... 9
GENERAL TROUBLESHOOTING................................................................................................................................................................9
GENERAL MAINTENANCE .......................................................................................................................................................................9
RETURNS PROCEDURE........................................................................................................................................................................10
TECHNICAL SPECIFICATIONS......................................................................................................................................... 11
CONTACT US......................................................................................................................................................................................12

Gobo Zoom LED 2.0 (Rev. 3) Page 3 of 12
1.BEFORE YOU BEGIN
What is Included
•1 x Gobo Zoom™ LED 2.0
•1 x Set of four colored gels
•1 x Set of eight replacement gobos
•1 FREE gobo of Chauvet’s logo
•1 x Power cord
•1 x Warranty card
•1 x User Manual
Unpacking Instructions
Immediately upon receiving a product, carefully unpack the carton, check the contents
to ensure that all parts are present, and have been received in good condition.
Claims
If the container or the material inside the container (this product
and any other
accessory included) appears damaged from shipping, or shows signs of mishandling,
notify the carrier immediately, not CHAUVET®,
upon receipt of the damaged
merchandise. Failure to do so in a timely manner may invalidate your claim with the
carrier. In addition, retain the container and all the packing material for inspection.
For other issues such as missing components or parts, damage not related to
shipping, or concealed damage, file a claim with CHAUVET® within seven (7) days of
receiving the merchandise.
Manual Conventions
CHAUVET® manuals use the following conventions to differentiate certain types of
information from the regular text.
CONVENTION MEANING
[10] A DIP switch to be configured
<Menu> A key to be pressed on the product’s control panel
1~512 A range of values
50/60 A set of values of which only one can be chosen
Settings A menu option not to be modified (for example, showing the operating
mode/current status)
MENU >
Settings A sequence of menu options to be followed
ON
A value to be entered or selected
Icons
This manual uses the following icons to indicate information that requires special
attention on the part of the user.
ICONS MEANING
Critical installation, configuration or operation information. Failure to
comply with this information may render the product partially or completely
inoperative, cause damage to the product or cause harm to the user.
Important installation or configuration information. Failure to comply with
this information may prevent the product from functioning correctly.
Useful non critical information.

Page 4 of 12 Gobo Zoom LED 2.0 (Rev. 3)
Safety Notes
•Please keep this User Manual for future consultation. If you sell the unit to another
user, be sure that they also receive this instruction booklet.
•Always make sure that you are connecting to the proper voltage, and that the line
voltage you are connecting to is not higher than that stated on the decal or rear panel
of the product.
•This product is intended for indoor use only! To prevent risk of fire or shock, do not
expose product to rain or moisture.
•Make sure there are no flammable materials close to the unit while operating.
•The unit must be installed in a location with adequate ventilation, at least 20 in (50 cm)
from adjacent surfaces. Be sure that no ventilation slots are blocked.
•Always disconnect from power source before servicing or replacing fuse and be sure to
replace with same fuse source.
•Secure product to fastening device using a safety chain.
•Maximum ambient temperature (Ta) is 104° F (40° C). Do not operate product at
temperatures higher than this.
•In the event of a serious operating problem, stop using the unit immediately. Never try
to repair the unit by yourself. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center.
•Never connect the device to a dimmer pack.
•Make sure the power cord is never crimped or damaged.
•Never disconnect the power cord by pulling or tugging on the cord.
•Never carry the product directly from the cord. Always use the hanging/mounting
bracket.
•Avoid direct eye exposure to the light source while it is on.
Please read these instructions carefully. It includes important information
about the installation, usage and maintenance of this product.

Gobo Zoom LED 2.0 (Rev. 3) Page 5 of 12
2.INTRODUCTION
Product Overview
Power In
DMX Out
Bracket
Adjustment Knob
Safety
Bracket
Adjustment Knob
Mounting Bracket
DIP Switches
DMX In
Fuseholder
Zoom Thumbscrew
Adjustment
Focus Thumbscrew
Adjustment
Gobo Holder

Page 6 of 12 Gobo Zoom LED 2.0 (Rev. 3)
3.SETUP
AC Power
This product runs on 100~240 VAC, 50/60 Hz. Before powering on the unit, make sure
the line voltage to which you are connecting it is within the range of accepted voltages.
To determine the power requirements for a particular product, see the label affixed to the
back plate of the product or refer to the product’s specifications chart. A product’s listed
current rating indicates its average current draw under normal conditions.
Always connect the product to a switched circuit. Never connect the product to a
rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer
channel is used only as a 0 to 100% switch.
Always connect the product to a circuit with a suitable electrical ground.
Replacing the Gobo/Color Gel
This product has replaceable gobos and colored gels. See the instructions below.
1. Remove power to the Gobo Zoom™ LED 2.0.
2. On the underside of the product, locate the two thumbscrews that secure the
gobo holder in place.
3. Remove the thumbscrews and carefully slide the gobo holder vertically apart
from the product.
4. Locate the gobo retainer ring and remove it. Use caution for this step, as the
retainer ring will be under tension. This may cause the ring to be difficult to
remove, as well as unstable after removal. Be careful not to lose it.
5. Remove any gobo that may already be installed.
6. Place the new color gel and gobo in position in the gobo holder, shown below.
7. Reinstall the gobo retainer ring securely.
8. Slide the gobo holder back into the product and tighten the two thumbscrews.
NOTE: To make your own gobos, buy any transparency from an office supply store that is less than
1 mm thick. See www.chauvetlighting.com for more information.
Gobo Holder
Thumbscrews
Gobo
Retainer Ring
Gobo
Color Gel

Gobo Zoom LED 2.0 (Rev. 3) Page 7 of 12
Mounting
Orientation
The Gobo Zoom™ LED 2.0may be mounted in any position, provided there is
adequate room for ventilation.
Rigging
Be sure that the structure can support the weight of the product. Please see the
“Technical Specifications” section of this manual for a detailed weight listing. Mount
the product securely. This may be done with a screw, nut and bolt, or a hanging
clamp. The hole in each bracket is 13 mm in size. When rigging consider routine
maintenance and control panel access. Please see the following notes on installation.
•When aiming the products, you may use the bracket adjustment knob.
Loosen the knob, adjust to the desired angle, and then tighten the knob by
turning clockwise. Do not use tools for this step, as it may cause damage.
•
Safety cables must always be used.
Mounting
bracket
Do not use a tool on
the bracket
adjustment knob

Page 8 of 12 Gobo Zoom LED 2.0 (Rev. 3)
4.OPERATING INSTRUCTIONS
Configuring the Starting Address
The Gobo Zoom™ LED 2.0 product uses
two
DMX channels. The highest channel that
the product may be set to in order to function properly is 511. Any address higher than this
will prevent access to all of the channels.
If this is your first time using DMX, we recommend reading the “DMX Primer” section in
the “Appendix”.
DMX Operation
This is the operating mode which will allow for control with an external DMX controller.
You must set the starting address for this mode. If this is your first time using DMX, then it
is recommended that you refer to the “DMX Primer” section in the “Appendix” of this
manual.
Mode DIP switches
DMX 1~9 = set to the DMX starting address
10 = On (DMX mode)
Standalone
This product has preprogrammed operating modes. These are accessed via the DIP
switches on the back of the product.
DIP switch [10] must be OFF in this mode.
Please see the chart below for further explanation.
Mode
100% Dimmer, Slow Rotation Speed
100% Dimmer, Medium Rotation
Speed
100% Dimmer, Fast Rotation Speed
100% Dimmer, No Rotation
DIP switches
1 = ON
2 = ON
3 = ON
4 = ON
The DIP switches will not work together. Higher the switch values have higher priority. Only
use one out of the four modes listed above!
DMX Channel Values
CHANNEL
VALUE
FUNCTION
1
000

255
Dimmer
0%~100%
2
000

255
Gobo Rotation
Slow~fast
The product ships with the gobos shown below.

Gobo Zoom LED 2.0 (Rev. 3) Page 9 of 12
5.APPENDIX
General Troubleshooting
SYMPTOM
POSSIBLE CAUSE(S)
POSSIBLE ACTION(S)
Breaker/Fuse
keeps blowing
•Excessive circuit load
•Check total load placed on the
electrical circuit.
•Short circuit along the power
wires •Check for a short in the electrical wiring (internal and/or external).
Device does not
power up
•No power
•Check for power on Mains.
•Loose power cord •Check power cord
Product is not
responding to DMX
•Wrong DMX addressing
•Check Control Panel and unit
addressing
•Damaged DMX cables
•Check DMX cables
•Wrong polarity settings on the
controller
•Check polarity switch settings on
the controller
•Loose DMX cables
•Check cable connections
•Faulty DMX interface
•Replace DMX input
•Faulty Main PCB
•Replace Main PCB
Loss of signal
•Non DMX cables
•Use only DMX compatible cables
•Bouncing signals
•Install terminator as suggested.
•Long cable / Low level signal
•Install amplifier right after product
with strong signal.
•Too many products
•Install an optically coupled DMX
splitter after unit #32.
•Interference from AC wires
•Keep DMX cables separated from
power cables or black lights.
If you still have a problem after trying the above solutions, please contact CHAUVET®
Technical Support.
General Maintenance
To maintain optimum performance and minimize wear, products should be cleaned
frequently. Usage and environment are contributing factors in determining frequency.
As a general rule, products should be cleaned at least twice a month. Dust build up
reduces light output performance and can cause overheating. This can lead to
reduced lamp life and increased mechanical wear. Be sure to power off product before
conducting maintenance.
•Unplug product from power.
•Use a vacuum or air compressor and a soft brush to remove dust collected
on external vents.
•Clean all lenses when the product is cool with a mild solution of glass cleaner
or Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue.
•Apply solution to the cloth or tissue and drag dirt and grime to the outside of
the lens.
•Gently polish optical surfaces until they are free of haze and lint.
The cleaning of external optical lenses and/or mirrors must be carried out periodically
to optimize light output. Cleaning frequency depends on the environment in which the
product operates. Damp, smoky or particularly dirty surroundings can cause greater
accumulation of dirt on the unit’s optics. Clean with soft cloth using normal glass

Page 10 of 12 Gobo Zoom LED 2.0 (Rev. 3)
cleaning fluid. Clean the external optics at least every 20 days. Clean the product at
least every 30/60 days.
Always dry the parts carefully after cleaning them.
Never spin a fan using compressed air.
Returns Procedure
Returned merchandise must be sent prepaid and in the original packing; call tags will
not be issued. Package must be clearly labeled with a Return Merchandize
Authorization Number (RMA #). Products returned without the RMA # will be refused.
Call CHAUVET® and request an RMA # prior to shipping the product. Be prepared to
provide the model number, serial number and a brief description of the cause for the
return. Be sure to pack product properly; any shipping damage resulting from
inadequate packaging is the customer’s responsibility. As a suggestion, proper UPS
packing or double-boxing is always a safe method to use. CHAUVET® reserves the
right to use its own discretion to repair or replace product(s).
If you are given an RMA #, please include the following information on a piece of
paper inside the box:
1) Your name
2) Your address
3) Your phone number
4) The RMA #
5) A brief description of the symptoms

Gobo Zoom LED 2.0 (Rev. 3) Page 11 of 12
TECHNICAL SPECIFICATIONS
WEIGHT & DIMENSIONS
Length ..................................................................................................................................................................9 in (230 mm)
Width ....................................................................................................................................................................7 in (186 mm)
Height...................................................................................................................................................................7 in (182 mm)
Weight ...................................................................................................................................................................4.4 lbs (2 kg)
POWER
Auto-ranging power supply..................................................................................................................100~240 VAC, 50/60 Hz
Power consumption @ 120 V................................................................................................... 18 W (0.3 A) max, 0.2 A inrush
Power consumption @ 230 V................................................................................................... 17 W (0.2 A) max, 0.2 A inrush
GOBO DIMENSIONS
Outside.........................................................................................................................................................................28.6 mm
Image ..............................................................................................................................................................................26 mm
Maximum thickness...........................................................................................................................................................1 mm
LIGHT SOURCE
Type ..........................................................................................................................................high-power, single source LED
Quantity....................................................................................................................................................................................1
Rating (white) ........................................................................................................................................ (15 W) 4 A, 50,000 hrs
PHOTO OPTIC
Zoom angle ...................................................................................................................................................................18°~25°
INDOOR/OUTDOOR
Rating..........................................................................................................................................................For indoor use only
THERMAL
Maximum ambient temperature...........................................................................................................................104° F (40° C)
CONTROL & PROGRAMMING
Data input............................................................................................................................... locking 3-pin XLR female socket
Data output................................................................................................................................ locking 3-pin XLR male socket
Data pin configuration ................................................................................................................pin 1 shield, pin 2 (-), pin 3 (+)
Protocol ........................................................................................................................................................... DMX-512 USITT
DMX Channels .........................................................................................................................................................................2
ORDERING INFORMATION
Gobo Zoom™ LED 2.0................................................................................................................................GOBOZOOMLED2
WARRANTY INFORMATION
Warranty................................................................................................................................................ 2-year limited warranty

Page 12 of 12 Gobo Zoom LED 2.0 (Rev. 3)
Contact Us
World Headquarters
United Kingdom & Ireland
CHAUVET® CHAUVET® Europe Ltd.
General Information
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Toll free: [phone]
Technical Support
Voice: [phone] (Press 4)
Fax: [phone]
Email: [email protected]
General Information
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Email: [email protected]
World Wide Web
www.chauvetlighting.com
World Wide Web
www.chauvetlighting.co.uk