Chauvet Q-Wash LED User manual

Snapshot
Ok on Dimmer
Outdoor OK
Sound Activated
DMX/Master/Slave
115V/230V Switch
Replaceable Fuse
User Serviceable
Duty Cycle
Q-Wash LED™
USER MANUAL
Chauvet, 3000 N 29th Ct, Hollywood, FL 33020 U.S.A
[phone] – [phone]
FAX [phone]
www.chauvetlighting.com

TABLE OF CONTENTS
1. BEFORE YOU BEGIN....................................................................................................................................................... 3
UNPACKING INSTRUCTIONS...................................................................................................................................................3
CONTACT US.......................................................................................................................................................................3
IMPORTANT SAFETY INFORMATION........................................................................................................................................4
FUSE REPLACEMENT............................................................................................................................................................4
2. INTRODUCTION ............................................................................................................................................................... 5
FEATURES ...........................................................................................................................................................................5
DMX CHANNEL SUMMARY....................................................................................................................................................5
PRODUCT OVERVIEW ...........................................................................................................................................................6
3. SETUP............................................................................................................................................................................... 7
AC POWER ..........................................................................................................................................................................7
MOUNTING...........................................................................................................................................................................7
FIXTURE LINKING..................................................................................................................................................................8
Data Cabling................................................................................................................................................................. 8
DMX Data Cable......................................................................................................................................................... 8
Cable Connectors ....................................................................................................................................................... 8
3-Pin to 5-Pin Conversion Chart ................................................................................................................................. 9
SETTING UP A DMX SERIAL DATA LINK .................................................................................................................................9
STAND-ALONE/MASTER-SLAVE .............................................................................................................................................9
FIXTURE LINKING..................................................................................................................................................................9
4. OPERATING INSTRUCTIONS........................................................................................................................................ 10
NAVIGATING THE CONTROL PANEL......................................................................................................................................10
OPERATING MODES............................................................................................................................................................10
Master/Stand-alone Operation.................................................................................................................................... 10
Slave Mode Operation................................................................................................................................................ 11
DMX Mode Operation................................................................................................................................................. 11
Creating Custom Programs ........................................................................................................................................ 11
ADDITIONAL MENU OPTIONS...............................................................................................................................................12
To set the pan to inverting or non-inverting: ............................................................................................................... 12
To set the tilt to inverting or non-inverting:.................................................................................................................. 12
To reset the fixture:..................................................................................................................................................... 12
To restore all settings to their factory defaults:........................................................................................................... 12
5. APPENDIX....................................................................................................................................................................... 13
DMX PRIMER.....................................................................................................................................................................13
MAINTENANCE....................................................................................................................................................................13
RETURNS PROCEDURE.......................................................................................................................................................14
CLAIMS..............................................................................................................................................................................14
DMX CHANNEL VALUES .....................................................................................................................................................14
MENU MAP.........................................................................................................................................................................15
TECHNICAL SPECIFICATIONS...............................................................................................................................................16
TECHNICAL SUPPORT.........................................................................................................................................................16
Q-Wash LED User Manual 2 Revised: 2006-12-11 11:35:30

1.BEFORE YOU BEGIN
Unpacking Instructions
Immediately upon receiving a product, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.
Note: If you should require sending any items back to CHAUVET, call CHAUVET for a (RMA) Return
Merchandise Authorization number. The factory will not allow any shipments without an RMA.
Your shipment includes the following:
¾1 x Q-Wash LED™
¾1 x Power cable
¾Warranty Card
¾Users Manual
Contact Us
World Wide
General Information Chauvet Lighting
3000 North 29th Court
Hollywood, FL 33020
voice: 954.929.1115
fax: [phone]
toll free: 800.762.1084
Technical Support Chauvet Lighting
3000 North 29th Court
Hollywood, FL 33020
voice: 954.929.1115 (Press 4)
fax: [phone] (Attention: Service)
World Wide Web www.chauvetlighting.com
Q-Wash LED User Manual 3 Revised: 2006-12-11 11:35:30

Important Safety Information
This product is designed for professional use. It is not intended for use in a household environment.
This product presents risks of lethal or severe injury due to fire and heat, electric shock, ultraviolet
radiation, lamp explosion, and injury from falls. Read this manual before installing or powering the
fixture, follow the safety precautions listed below and observe all warnings in this manual and on the
fixture. If you have any questions about how to operate the fixture safely, please contact CHAUVET.
Protection against Electric Shock
•Always disconnect from AC power source before servicing or replacing lamp or fuse.
•All Class I fixtures must be connected to circuits with a suitable Earth Ground.
•To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no
flammable materials close to the unit while operating.
•Make sure power cord is never crimped or damaged.
•Never disconnect power cord by pulling or tugging on the cord.
Protection against Fire & Burns
•Always make sure that you are connecting to the proper voltage and that the line voltage you are
connecting to is not higher than that stated on decal or rear panel of the fixture.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Maintain a minimum distance of 1 meter (3.28 feet) from combustible materials.
•Maximum ambient temperature (Ta) is: 35°C(95°F). Do not operate fixture at temperatures
higher than this.
Protection against Injury to persons
•Secure fixture to fastening device using a safety chain.
•Do not open fixture for a minimum of 15 minutes after switching off.
•In the event of serious operating problem, stop using the unit immediately. Never try to repair the
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.
Please contact the nearest authorized technical assistance center. Always use the same type
spare parts.
Caution! There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service,
please contact CHAUVET.
Fuse Replacement
The fuse is located
inside this
compartment.
Remove using a flat
head screwdriver.
Disconnect the power cord before replacing a fuse and always
replace with the same type fuse.
With a flat head screwdriver wedge the fuse
holder out of its housing. Remove the damaged
fuse from its holder and replace with exact
same type fuse. Insert the fuse holder back in
its place and reconnect power.
Q-Wash LED User Manual 4 Revised: 2006-12-11 11:35:30

2.INTRODUCTION
Features
•10-channel DMX-512 LED moving yoke color wash
•Pan: 540o/ tilt: 270o
•RGB color mixing
•Variable electronic strobe
•Variable electronic dimmer (0 - 100%)
•Remote fixture reset and vector speed channel
Additional Features
•Extremely bright 1W LEDs
•Automatic pan & tilt correction
•100 user-programmable steps accessible via master/slave or DMX
•Built-in automated programs via master/slave or DMX
•Built-in sound activated programs via master/slave or DMX
•Micro-stepping motors
•LCD display
•Reset to factory settings option
•Low power consumption
•Reversible pan and tilt
•Thermal switch
•Fan cooled (adjustable speeds)
DMX Channel Summary
CHANNEL FUNCTION
1 Pan
2 Tilt
3 Vector Speed (Pan/Tilt)
4 Red
5 Green
6 Blue/Auto-Color Speed
7 Linear Color-Macros/Auto-Color
8 Dimmer
9 Strobe
10 Mode
Q-Wash LED User Manual 5 Revised: 2006-12-11 11:35:30

Product Overview
Yoke
Base
Head
DMX OUT
DMX IN
110V~230V
POWERINPUT
POWER MIC
MODE UP DOWN ENTER
FUSE
DMX
Connectors
Control
Buttons
IEC Power
Connector
Power
Switch
Microphone
LCD
Display
Fuse
Voltage
Select
Switch
Q-Wash LED User Manual 6 Revised: 2006-12-11 11:35:30

3.SETUP
AC Power
Warning! Verify that the voltage select switch on your unit matches the line voltage applied.
Damage to your fixture may result if the line voltage applied does not match the
voltage indicated on the voltage selector switch. All fixtures must be connected to
circuits with a suitable Earth Ground.
•To determine the power requirements for a particular fixture, see the label affixed to the back plate
of the fixture or refer to the fixture’s specifications chart.
•A fixture’s listed current rating is its average current draw under normal conditions.
•All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat
(variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0%
to 100% switch.
•Before applying power to a fixture, check that the source voltage matches the fixture’s
requirement, and that the fuse is the value specified for the operating voltage (110V operation =
2A 125V/250V fast blow; 230V operation = 1A 250V fast blow).
•All fixtures must be connected to circuits with a suitable Earth Ground.
Power Cable Configuration
CABLE Pin International Screw Color
BROWN Live L Yellow or
Brass
BLUE Neutral N Silver
YELLOW/GREEN Earth EG (Ground) Green
Mounting
Orientation
Hanging Clamp
This fixture can be mounted on a truss using a clamp in any position or against a flat surface using
the brackets provided.
Rigging
The fixture includes two brackets with ¼ turn locks for attaching a
standard truss mounting hanging clamp. You must supply your own
clamp and make sure the clamp is capable of supporting the weight
of this fixture. You can order C-clamps from any CHAUVET
dealer or distributor.
1. Block access below the work area and use suitable and
stable platform when installing or servicing fixture.
2. Align the clamp screw with the center hole on the yoke
and tighten.
3. Verify the structure can hold 10 times the weight of all to-
be installed fixtures.
4. Adjust the angle on the yoke arm as necessary.
5. Always use a safety cable or chain as a secondary
source of attachment. The safety cable must hold 10
times the weight of the fixture. If safety cable attachment
point is provided that is permanently affixed to the
surface or body of the fixture, use that instead of looping
through a hanging yoke/arm.
Q-Wash LED User Manual 7 Revised: 2006-12-11 11:35:30

Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller
or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The
combined number of channels required by all the fixtures on a serial data link determines the number
of fixtures the data link can support.
The Q-Wash LED fixtures use 10 channels of DMX control.
Important: Fixtures on a serial data link must be daisy chained in one single line. To comply with the EIA-485
standard no more than 32 devices should be connected on one data link. Connecting more than 32
fixtures on one serial data link without the use of a DMX optically-isolated splitter may result in
deterioration of the digital DMX signal.
Maximum recommended serial data link distance: 500 meters (1640 ft.)
Maximum recommended number of fixtures on a serial data link: 32 fixtures
Data Cabling
To link fixtures together you must obtain data cables. You can purchase CHAUVET-certified DMX
cables directly from a dealer/distributor or construct your own cable. If you choose to create your own
cable please use data-grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.
DMX Data Cable
Use a Belden© 9841 or equivalent cable which meets the specifications for EIA RS-485 applications.
Standard microphone cables cannot transmit DMX data reliably over long distances. The cable will
have the following characteristics:
2-conductor twisted pair plus a shield
Maximum capacitance between conductors – 30 pF/ft.
Maximum capacitance between conductor and shield – 55 pF/ft.
Maximum resistance of 20Ω/ 1000 ft.
Nominal impedance 100 - 140Ω
Cable Connectors
Cabling must have a male XLR connector on one end and a female XLR connector on the other end.
can cause a ground loop, and your fixture may perform erratically. Test cables with an ohm meter to r.
Resistance 120
ohm 1/4w between
pin 2 (DMX -) and
pin 3 (DMX +) of
the last fixture.
CO
MM
O
N
DMX
+
DMX
-
INPUT OUTPUT
1
3
2
1
3
2
1
3
2
Termination reduces signal errors and
to avoid signal transmission problems
and interference, it is always
advisable to connect a DMX signal
terminator.
DMX connector configuration
CAUTION Do not allow contact between the common and the fixture’s chassis ground. Grounding the common
verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each othe
Q-Wash LED User Manual 8 Revised: 2006-12-11 11:35:30

3-Pin to 5-Pin Conversion Chart
Note! If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter.
CHAUVET Model No: DMX5M.
The chart below details a proper cable conversion:
3PIN TO 5PIN CONVERSION CHART
Conductor 3 Pin Female (output) 5 Pin Male (Input)
Ground/Shield Pin 1 Pin 1
Data ( - )signal Pin 2 Pin 2
Data ( + ) signal Pin 3 Pin 3
Do not use Do not use
Do not use Do not use
Setting up a DMX Serial Data Link
This drawing provides a
general illustration of the
DMX Input/Output panel
of a lighting fixture.
Universal DMX Controller
Continue the link
1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector
of the controller.
2. Connect the end of the cable coming from
the controller which will have a (female) 3
pin connector to the input connector of the
next fixture consisting of a (male) 3 pin
connector.
3. Then, proceed to connect from the output
as stated above to the input of the following
fixture and so on.
CHAUVET Certified DMX Data Cables
Order Code Description
DMX1.5 DMX Cable 1.5m/4.9ft
DMX4.5 DMX Cable 4.5m/14.8ft
DMX10 DMX Cable 10m/32.8ft
Stand-alone/Master-Slave
Fixture Linking
1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector
of the first fixture.
2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin
connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then,
proceed to connect from the output as stated above to the input of the following fixture and so on.
Often, the setup for Master-Slave
and stand-alone operation
requires that the first fixture in the
chain be initialized for this
purpose via either settings in the
control panel or DIP-switches.
Secondarily, the fixtures that
follow may also require a slave
setting. Please consult the
“Operating Instructions” section
in this manual for complete
instructions for this type of setup
and confi
g
uration.
Q-Wash LED User Manual 9 Revised: 2006-12-11 11:35:30

4.OPERATING INSTRUCTIONS
Navigating the Control Panel
Access control panel functions using the four panel buttons located directly underneath the LCD
Display.
MODE UP DOWN ENTER
Button Function
<MODE> Used to access the menu or to return to a
previous menu option
<UP> Scrolls through menu options in ascending
order
<DOWN> Scrolls through menu options in descending
order
<ENTER> Used to select and store the current menu
or option within a menu
The Control Panel LED Display shows the menu items you select from the menu map on page 15.
When a menu function is selected, the display will show immediately the first available option for the
selected menu function. To select a menu item, press <ENTER>.
Press the <MODE> button repeatedly until MENU appears on the top line of the display. This is the
top of the menu map. What appears on the bottom line of the display is one of the four choices in the
menu map. Use the <UP> and <DOWN> buttons to navigate the menu map and menu options. Press
the <ENTER> button to access the menu function currently displayed or to enable a menu option. To
return to the previous option or menu without changing the value, press the <MODE> button.
Operating Modes
Master/Stand-alone Operation
This mode allows the unit to operate either as a stand-alone unit, or as the master of one or more
slave units.
Menu
Run 1) In the menu, select “Run”.
2) Scroll through and select a program. The program options are: “Auto1”, “Auto2”, “Sound1”,
“Sound2”, and “Custom”. Select the desired program from the available options. That program
will then begin running.
Run
(Auto1,
Auto2,
Sound1,
Sound2,
or
Custom)
3) For Master operation, use standard DMX cables to daisy chain your units together via the DMX
connector on the rear of the units. For longer cable runs we suggest a terminator at the last
fixture. For more information about terminators, see page 8.
Program Description
Auto1 Program that runs on a predetermined time interval that is fixed.
Auto2 Program that runs on a predetermined time interval that is fixed.
Sound1 Same as “Auto1”, except that each step of the program occurs
when a beat is detected from the built-in microphone.
Sound2 Same as “Auto2”, except that each step of the program occurs
when a beat is detected from the built-in microphone.
Custom User-programmable scene, which can be programmed by following
the instructions on page 11.
Q-Wash LED User Manual 10 12/11/2006/11:35

Slave Mode Operation
Menu
Run
Run
Slave
This mode allows the unit to operate as the slave of another Master unit. Up to 32 fixtures may be
linked together in this mode.
1) In the menu, select “Run”. Next, scroll through until “Slave” is displayed, and select it. Press
<MODE> until “Run” is displayed on the second line.
2) Use standard DMX cables to daisy chain your units together via the DMX connector on the rear
of the units. For longer cable runs we suggest a terminator at the last fixture. For more
information about terminators, see page 8.
DMX Mode Operation
This mode allows the unit to be controlled by any universal DMX controller. If you are unfamiliar with
DMX, please read the DMX Primer on page 13.
Menu
Run
Run
DMX
1) In the menu, select “Run”. Next, select “DMX”. Press <MODE> until “Run” is displayed on the
second line.
2) Scroll through until “Address” is displayed, and select it. Use the <UP> and <DOWN> buttons to
input the desired DMX starting address. Press <ENTER> to set the DMX starting address.
3) Use standard DMX cables to daisy chain your units together via the DMX connector on the rear
of the units. For longer cable runs we suggest a terminator at the last fixture. For more
information about terminators, see page 8.
Creating Custom Programs
In order to create a custom program than can be run in any mode, do the following:
Menu
Edit Prg
Edit
Program
Step
001-100
Pan
000-255
Tilt
000-255
Red
000-255
Green
000-255
Blue
000-255
Strobe
000-255
Time
000-008
Fade
0-008*
1) In the menu, select “Edit Prg”. Next, scroll through until “Edit Program” is displayed, and select it.
2) Scroll through to the step you wish to program, and select it.
Note: The program runs in sequential order, starting with step 001, and continuing through
the last step that was programmed. It is therefore not necessary to program all 100
steps. In other words, if only steps 001, 002, and 003 are programmed, the routine will
start again at step 001 after step 003 has finished executing.
3) “Pan” will be displayed on the top line of the screen. Scroll through to the pan value you wish to
program, and select it. Repeat this for the “Tilt”, “Red”, “Green”, “Blue”, “Strobe”, “Time”, and
“Fade” values. Note that “Time” is the length of time in seconds that the current step will run, and
must be a value between 0 and 8. Also note that the value of “Fade” cannot be larger than the
value of “Time”. “Fade” is the amount of time, in seconds, that the fixture will take to gradually
transition between the previous step and the current step. If the value of “Fade” is 0, the
transition will be at the maximum speed possible.
4) Repeat steps 2 and 3 until the program is created. To end programming, press <MODE> until
“Menu” is displayed.
5) To reset (erase) the custom program, select “Edit Prg” from the menu. Scroll through to “Reset
Custom” and select it; “Confirm Reset” will be displayed. Press <ENTER> to reset the fixture.
The program can be run in any mode. See the above instructions for the desired operating mode in
order to run the custom program.
*Note: Fade value cannot exceed time value. For example, if time is set to 4, fade can be 0-4.
Q-Wash LED User Manual 11 12/11/2006/11:35

Additional Menu Options
This fixture can be customized in several different ways at the discretion of the user. This section
details how to change the fan speed, invert the Pan, invert the Tilt, reset the fixture, and restore the
fixture to factory default settings.
To change the fan speed:
1) In the menu, select “Options”. Scroll through to “Fan Speed”, and select it.
Menu
Options
Fan
Speed
2) Scroll to the desired speed, either “Low” or “High”, and select it.
To set the pan to inverting or non-inverting:
1) In the menu, select “Options”. Scroll through to “Invert Pan” and select it.
Menu
Options
Invert
Pan
2) Scroll to “Pan On” or “Pan Off” and select the desired setting. Note that “Pan On” inverts the pan
values, and “Pan Off” uses the standard pan values.
To set the tilt to inverting or non-inverting:
1) In the menu, select “Options”. Scroll through to “Invert Tilt” and select it.
Menu
Options
Invert
Tilt
2) Scroll to “Tilt On” or “Tilt Off” and select the desired setting. Note that “Tilt On” inverts the tilt
values, and “Tilt Off” uses the standard tilt values.
To reset the fixture:
1) In the menu, select “Options”. Scroll through to “Reset” and select it. The fixture will then reset
itself.
Menu
Options
Reset
To restore all settings to their factory defaults:
1) In the menu, select “Options.” Scroll through to “Load Default” and select it. This will restore all
settings to their factory defaults.
Menu
Options
Load
Default
Q-Wash LED User Manual 12 12/11/2006/11:35

5.APPENDIX
DMX Primer
There are 512 channels in a DMX-512 connection, though all 512 channels do not need to be used.
Channels may be assigned in any manner. A fixture capable of receiving DMX-512 will require one or
a number of sequential channels. The user must assign a starting address on the fixture that
indicates the first channel reserved in the controller. There are many different types of DMX
controllable fixtures and they all may vary in the total number of channels required. Choosing a start
address should be planned in advance. Channels should never overlap. If they do, this will result in
erratic operation of the fixtures whose starting address is set incorrectly. You can however, control
multiple fixtures of the same type using the same starting address as long as the intended result is
that of unison movement or operation. In other words, the fixtures will be slaved together and all
respond exactly the same.
DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is
where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which
the fixtures are connected is not important and has no effect on how a controller communicates to
each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures
using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The
shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET
carries 3-pin DMX-compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’). Contact the
nearest Chauvet dealer to order any of these cables.
Maintenance
To maintain optimum performance and minimize wear, fixtures should be cleaned frequently. Usage
and environment are contributing factors in determining frequency. As a general rule, fixtures should
be cleaned at least twice a month. Dust build up reduces light output performance and can cause
overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off
fixture before conducting maintenance.
Unplug fixture from power. Use a vacuum or air compressor and a soft brush to remove dust
collected on external vents and internal components. Clean all glass when the fixture is cold with a
mild solution of glass cleaner or Isopropyl Alcohol and a soft lint-free cotton cloth or lens tissue. Apply
solution to the cloth or tissue and drag dirt and grime to the outside of the lens. Gently polish optical
surfaces until they are free of haze and lint. Do not to touch the lamp glass when cleaning fixture. Oil
and dirt can cause damage and premature aging of the lamp. In the event that the lamp is touched or
becomes dirty, clean the lamps with an alcohol wipe.
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates:
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s
optics. Clean with soft cloth using normal glass cleaning fluid. - Always dry the parts carefully. - Clean
the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.
Q-Wash LED User Manual 13 12/11/2006/11:35

Returns Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Merchandise Authorization Number (RA #). Products
returned without an RA # will be refused. Call CHAUVET and request an RA # prior to shipping the
fixture. Be prepared to provide the model number, serial number and a brief description of the cause
for the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate
packaging is the customer’s responsibility. CHAUVET reserves the right to use its own discretion to
repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is always a safe
method to use.
Claims
Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim
for items such as missing component/part, damage not related to shipping, and concealed damage,
must be made within seven (7) days of receiving merchandise.
DMX Channel Values
CHANNEL VALUE FUNCTION
1 000 Ù255 Pan: 128 = halfway point
2 000 Ù255 Tilt: 128 = halfway point
3 000 Ù255 Vector Speed (Pan/Tilt): (Normal > Slow)
4 000 Ù255 Red (0 – 100%)
5 000 Ù255 Green (0 – 100%)
6 000 Ù255 Blue (0 – 100%)
Auto-color speed when CH7 = 241-255
7
000 Ù005
006 Ù035
036 Ù065
066 Ù095
096 Ù125
126 Ù155
156 Ù185
186 Ù215
216 Ù240
241 Ù250
251 Ù255
No function
Red: 100%, Green varies: 0 – 100%
Red varies: 100 – 0%, Green: 100%
Green: 100%, Blue varies: 0 – 100%
Green varies: 100 – 0%, Blue: 100%
Red varies: 0 – 100%, Blue: 100%
Red: 100%, Blue varies: 100 – 0%
Red: 100%, Green varies: 0 – 100%, Blue varies: 0 – 100%
Red varies: 100 – 50%, Green varies: 100 – 50%, Blue varies: 100 – 50%
Auto-color
White
8 000 Ù255 Dimmer (0 – 100%)
9 000 Ù005
006 Ù255 No function
Strobe (Slow > Fast)
10
000 Ù045
046 Ù055
056 Ù095
096 Ù135
136 Ù175
176 Ù215
216 Ù255
No function
Reset (after 3 seconds)
Auto1 (after 3 seconds)
Auto2 (after 3 seconds)
Sound1 (after 3 seconds)
Sound2 (after 3 seconds)
Custom (after 3 seconds)
Q-Wash LED User Manual 14 12/11/2006/11:35

Menu Map
Menu
Menu Menu
Options Menu
Address Menu Run
Edit Prg
Run
Auto1 Run Auto2 Run Sound1 Run Sound2
Address
001-499
Fan
Speed Invert
Pan Invert Tilt Reset Load Default
Edit
Program
Step
001-100 Confirm Reset
Pan
000-255
Tilt
000-255
Red
000-255
Green
000-255
Blue
000-255
Strobe
000-255
Time
000-008
Fade
0-Time
Run
Custom
Run
DMX Run
Slave
Speed
Low Speed High Invert
Pan
Pan
On Pan
Off Tilt
On
Reset
Custom
Tilt
Off
When navigating the menu:
Use the “UP” button to move right.
Use the “DOWN” button to move left.
Use the “ENTER” button to move down.
Use the “MODE” button to move up.
Q-Wash LED User Manual 15 12/11/2006/11:35

Technical Specifications
WEIGHT & DIMENSIONS
Length........................................................................................................................... 14.0 in (356 mm)
Width ............................................................................................................................ 11.8 in (300 mm)
Height........................................................................................................................... 14.0 in (356 mm)
Weight ............................................................................................................................19.6 lbs (8.9 kg)
POWER
Operating Voltage ...............................................................................110V 50/60 Hz or 230V 50/60 Hz
AC input plug...................................................................................................................IEC 60320 C14
Power consumption.......................................................................................................................... 50W
Inrush.............................................................................................................................................. 216W
PHOTO OPTIC
Beam angle with included 15° lenses.................................................................................................30°
Beam angle with optional 30°lenses ................................................................................................. 45°
Pan...................................................................................................................................................540°
Tilt.....................................................................................................................................................270°
Illuminance ................................................................................................(406fc or 4369lux) @ 1 meter
LAMPS
Bulb ..........................................................................18 (6 red, 6 green, 6 blue) 1W LED’s, 100,000 hrs
FUSE
110V Operation ........................................................................ 2A 125V fast blow or 2A 250V fast blow
230V Operation ...........................................................................................................1A 250V fast blow
CONTROL & PROGRAMMING
Data input................................................................................................ locking 3-pin XLR male socket
Data output...........................................................................................locking 3-pin XLR female socket
Data pin configuration ..............................................................................pin 1 shield, pin 2 (-), pin 3 (+)
Protocols........................................................................................................................DMX-512 USITT
DMX Channels .....................................................................................................................................10
ORDERING INFORMATION
Q-Wash LED™..................................................................................................................Q-WASH LED
WARRANTY INFORMATION
Warranty.............................................................................................................. 2-year limited warranty
Technical Support
Address: Service Dept.
3000 N 29th Ct, Hollywood, FL 33020 (U.S.A.)
Support (Email): [email protected]
Telephone: [phone] - (Press 4)
Fax: [phone] - (Attention: Service)
Website: http://www.chauvetlighting.com
Q-Wash LED User Manual 16 12/11/2006/11:35