Chauvet Q-Wash 575 User manual

Snapshot
Ok on Dimmer
Outdoor OK
Sound Activated
DMX512
Master/Slave
Multitap
Transformer
Replaceable Fuse
User Serviceable
Duty Cycle
Q-Wash 575™
USER MANUAL
Chauvet, 3000 N 29th Ct, Hollywood, FL 33020 U.S.A.
[phone] – [phone]
FAX [phone]
www.chauvetlighting.com

TABLE OF CONTENTS
1. BEFORE YOU BEGIN....................................................................................................................................................... 3
WHAT IS INCLUDED.............................................................................................................................................................. 3
UNPACKING INSTRUCTIONS.................................................................................................................................................. 3
AC POWER ......................................................................................................................................................................... 3
CONTACT US...................................................................................................................................................................... 4
SAFETY INSTRUCTIONS........................................................................................................................................................ 4
2. INTRODUCTION ............................................................................................................................................................... 5
FEATURES .......................................................................................................................................................................... 5
DMX CHANNEL SUMMARY................................................................................................................................................... 5
PRODUCT OVERVIEW .......................................................................................................................................................... 6
3. SETUP............................................................................................................................................................................... 7
LAMP.................................................................................................................................................................................. 7
Lamp Installation........................................................................................................................................................... 7
Fuse Replacement........................................................................................................................................................ 8
FIXTURE LINKING................................................................................................................................................................. 8
Data Cabling................................................................................................................................................................. 8
DMX Data Cable.................................................................................................................................................... 8
Cable Connectors.................................................................................................................................................. 9
3-Pin to 5-Pin Conversion Chart............................................................................................................................ 9
SETTING UP A DMX SERIAL DATA LINK ................................................................................................................................9
MASTER/SLAVE FIXTURE LINKING ...................................................................................................................................... 10
MOUNTING........................................................................................................................................................................ 10
Orientation........................................................................................................................................................... 10
Rigging................................................................................................................................................................. 10
4. OPERATING INSTRUCTIONS........................................................................................................................................ 11
NAVIGATING THE CONTROL PANEL..................................................................................................................................... 11
MENU MAP........................................................................................................................................................................ 12
CONTROL PANEL FUNCTIONS ............................................................................................................................................ 13
Program Options......................................................................................................................................................... 13
User Configurations.................................................................................................................................................... 14
To set the pan to inverting or non-inverting:........................................................................................................ 14
To set the tilt to inverting or non-inverting: .......................................................................................................... 14
Service Functions ....................................................................................................................................................... 14
To reset the fixture:.............................................................................................................................................. 14
To turn the Lamp Power on or off:....................................................................................................................... 14
OPERATION....................................................................................................................................................................... 14
Stand-Alone Mode (Sound-Active, Auto Mode):......................................................................................................... 14
Master/Slave Mode (Master Sound, Master Auto):..................................................................................................... 15
DMX Mode.................................................................................................................................................................. 15
DMX CHANNEL VALUES .................................................................................................................................................... 15
GENERAL TROUBLESHOOTING ........................................................................................................................................... 17
TECHNICAL SUPPORT........................................................................................................................................................ 18
5. APPENDIX....................................................................................................................................................................... 18
DMX PRIMER.................................................................................................................................................................... 18
GENERAL MAINTENANCE ................................................................................................................................................... 18
RETURNS PROCEDURE...................................................................................................................................................... 19
CLAIMS............................................................................................................................................................................. 19
TECHNICAL SPECIFICATIONS.............................................................................................................................................. 19
Q-Wash 575 User Manual 2 8/3/2007 9:10:00 AM

1. BEFORE YOU BEGIN
What is included
¾1 x Q-Wash 575™
¾HMI 575W Lamp
¾Power Cord
¾Warranty Card
¾User Manual
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.
AC Power Figure 1 - AC Voltage Switch
To determine the power requirements for a
particular fixture, see the label affixed to the back
plate of the fixture or refer to the fixture’s
specifications chart. A fixture’s listed current
rating is its average current draw under normal
conditions. All fixtures must be powered directly
off a switched circuit and cannot be run off a
rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel is used solely
for a 0% to 100% switch. Before applying power
to a fixture, check that the source voltage
matches the fixture’s requirement. Check the
fixture or device carefully to make sure that if a
voltage selection switch exists that it is set to the
correct line voltage you will use.
100V
100V
115V
115V
208V
208V
230V
230V
240V
240V
50Hz
50Hz60HzININ
60Hz
Select v ol t age
To Ballast 230V/50Hz
To Ballast 230V/60Hz
Lamp Control to PCB in

AC-100-230V
INPUT
To TRANSFORMER
See the product overview for the
location of these switches.
Warning! Verify that the voltage select switch on your unit matches the line voltage applied,
and that the frequency select switch on your unit matches the frequency of the
power in your region. Also verify that you are using the correct fuse value for your
operating voltage. All fixtures must be connected to circuits with a suitable Earth
Ground. Damage to your fixture may occur if these instructions are not followed.
POWER CABLE PIN INTERNATIONAL
BROWN Live L
BLUE Neutral N
YELLOW/GREEN Earth EG (Ground)
OPERATING VOLTAGE MUST USE CORRECT FUSE
120V 15A
230V 10A
Q-Wash 575 User Manual 3 8/3/2007 9:10:00 AM

Contact Us
World Wide
General Information Chauvet Lighting
3000 North 29th Court
Hollywood, FL 33020
voice: 954.929.1115
fax: [phone]
toll free: 800.762.1084
Technical Support Chauvet Lighting
3000 North 29th Court
Hollywood, FL 33020
voice: 954.929.1115 (Press 4)
fax: [phone] (Attention: Service)
World Wide Web www.chauvetlighting.com
Safety Instructions
Please read these instructions carefully, which includes important
information about the installation, usage and maintenance of this
product.
•Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Always make sure that you are connecting to the proper voltage, and that the line voltage you are
connecting to is not higher than that stated on the decal or rear panel of the fixture.
•This product is intended for indoor use only!
•To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no
flammable materials close to the unit while operating.
•The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Always disconnect from power source before servicing or replacing lamp or fuse and be sure to
replace with same lamp source.
•Secure fixture to fastening device using a safety chain. Never carry the fixture solely by its head. Use
its carrying handles.
•Maximum ambient temperature (Ta) is 95°F (35°C). Do not operate fixture at temperatures higher
than this.
•In the event of a serious operating problem, stop using the unit immediately. Never try to repair the
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•Don’t connect the device to a dimmer pack.
•Make sure the power cord is never crimped or damaged.
•Never disconnect the power cord by pulling or tugging on the cord.
•Avoid direct eye exposure to the lamp while it is on.
Caution! There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service,
please contact CHAUVET at: 954-929-1115.
Q-Wash 575 User Manual 4 8/3/2007 9:10:00 AM

2. INTRODUCTION
Features
•16-channel DMX-512 moving yoke color wash
•Pan: 530°/ tilt: 280°
•Variable strobe/shutter
•CMY color mix system (cyan, magenta, yellow wheels)
•Color wheel
6 colors + white
Red, blue, green, purple, 3200º & 5000ºK correction filters
Rainbow color spin in both directions at variable speeds
•31 color macros
•Beam shaper effect
•Frost filter
•Variable motorized zoom (26°- 34°)
•Variable motorized dimmer (0 – 100%)
•Remote fixture reset, lamp on/off and vector speed channel
•Vector speed channel for CMY color mix system
Additional Features
•Automatic pan & tilt correction
•Micro-stepping motors
•LED display
•16bit pan/tilt resolution
•Thermal switch
•Fan cooled
DMX Channel Summary
CHANNEL FUNCTION
1 Pan
2 Tilt
3 Pan Fine (16-bit mode)
4 Tilt Fine (16-bit mode)
5 Vector Speed
6 Lamp and Reset
7 Color Wheel
8 Cyan
9 Magenta
10 Yellow
11 CMY Speed
12 Color Macro
13 Effect Wheel
14 Zoom
15 Strobe
16 Dimmer
Q-Wash 575 User Manual 5 8/3/2007 9:10:00 AM

Product Overview
Control
Panel
Access Plate
to Multitap
Transformer
Head
Yoke
Base
Carrying
Handle
Power Connector
& Fuse Holder
DMX
Output
Connecto
r
DMX Input
Connector
Power Switch
Q-Wash 575 User Manual 6 8/3/2007 9:10:00 AM

3. SETUP
Lamp
You will need to install a lamp prior to the initial operation of the fixture. A 575W HMI lamp is included.
Warning! When replacing the lamp, please wait 15 minutes after powering down to allow the
unit to cool down! Always disconnect from main power prior to lamp replacement.
Do not touch the envelope (glass area) of the bulb with bare hands. If this happens, clean the lamp
with alcohol and wipe it with a lint free cloth before installation.
Lamp Installation
1) Remove the four cover screws as indicated in
2) ws indicated in
3) wards the back of the head as
4) wards the back of
5)
6) p.
Warning: t be facing directly up
7) cloth and
8)
wards the front of the
10) n towards lamp and tighten the two
11)
Figure A
Figure B
Figure C
Figure D
figure A. Note that this is the side of the cover
with the fan showing.
Remove the two thumbscre
figure B.
Lift the fan to
indicated in figure B.
Pull the reflector housing to
the had as indicated in figure C.
Remove the two lamp screws indicated in
figure D.
Remove the lam
Nipple on lamp mus
or directly down with respect to the head.
In other words, the nipple should NOT be
pointing towards the back of the reflector,
or towards the front of the head. Damage
to the reflector can occur if these
instructions are not followed!
Hold the new lamp with a lint-free
insert into lamp socket, making sure that the
nipple on the lamp is pointing up or down, and
not towards the reflector or front.
Tighten lamp screws.
9) Gently push reflector to
head.
Lower fa
thumbscrews.
Replace top cover.
Q-Wash 575 User Manual 7 8/3/2007 9:10:00 AM

Disconnect the power cord before replacing a fuse and always
replace with the same type fuse.
Fuse Replacement
The fuse is located
inside this
compartment.
Remove using a flat
head screwdriver.
With a flat head screwdriver wedge the fuse
holder out of its housing. Remove the damaged
fuse from its holder and replace with exact
same type fuse. Insert the fuse holder back in
its place and reconnect power.
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller
or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The
combined number of channels required by all the fixtures on a serial data link determines the number
of fixtures the data link can support.
Important: Fixtures on a serial data link must be daisy chained in one single line. To comply with the EIA-485
standard no more than 32 devices should be connected on one data link. Connecting more than 32
fixtures on one serial data link without the use of a DMX optically-isolated splitter may result in
deterioration of the digital DMX signal.
Maximum recommended serial data link distance: 500 meters (1640 ft.)
Maximum recommended number of fixtures on a serial data link: 32 fixtures
Data Cabling
To link fixtures together you must obtain data cables. You can purchase CHAUVET-certified DMX
cables directly from a dealer/distributor or construct your own cable. If you choose to create your own
cable please use data-grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.
DMX DATA CABLE
Use a Belden© 9841 or equivalent cable which meets the specifications for EIA RS-485 applications.
Standard microphone cables cannot transmit DMX data reliably over long distances. The cable will
have the following characteristics:
2-conductor twisted pair plus a shield
Maximum capacitance between conductors – 30 pF/ft.
Maximum capacitance between conductor and shield – 55 pF/ft.
Maximum resistance of 20 ohms / 1000 ft.
Nominal impedance 100 – 140 ohms
Q-Wash 575 User Manual 8 8/3/2007 9:10:00 AM

CABLE CONNECTORS
This drawing provides a
general illustration of the
DMX Input/Output panel of
a lighting fixture.
U X Controllerniversal DM
Continue the link
Cabling must have a male XLR connector on one end and a female XLR connector on the other end.
can cause a ground loop, and your fixture may perform erratically. Test cables with an ohm meter to r.
3-PIN TO 5-PIN CONVE
pin DMX output connector, you will need to use a 5 pin to 3 pin adapter.
CHAUVET Model No: DMX5M, or DMX5F.
3PIN TO 5PIN C
duc 3 Pin Female (output) 5 Pin Male (Input)
CO
MMON
DMX
+
DMX -
INPUT OUTPUT
1
3
2
1
3
2
1
3
2
Resistance 120
ohm 1/4w between
pin 2 (DMX -) and
pin 3 (DMX +) of
the last fixture.
Termination reduces signal errors and
to avoid signal transmission problems
and interference, it is always
advisable to connect a DMX signal
terminator.
DMX connector configuration
CAUTION Do not allow contact between the common and the fixture’s chassis ground. Grounding the common
verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each othe
RSION CHART
Note! If you use a controller with a 5
The chart below details a proper cable conversion:
ONVERSION CHART
Con tor
Ground/Shield Pin 1Pin 1
Data ( - ) signal Pin 2 Pin 2
Data ( + ) signal Pin 3 Pin 3
Do not use Do not use
Do not use Do not use
Setting up a DMX Serial Data Link
e of
pin
2. a (female) 3
3. t as
to the input of the following
escription
.5m/14.8ft
1. Connect the (male) 3 pin connector sid
the DMX cable to the output (female) 3
connector of the controller.
Connect the end of the cable coming from
the controller which will have
pin connector to the input connector of the
next fixture consisting of a (male) 3 pin
connector.
Then, proceed to connect from the outpu
stated above
fixture and so on.
CHAUVET Certified DMX Data Cables
Order Code D
DMX1.5 DMX Cable 1.5m/4.9ft
DMX4.5 DMX Cable 4
DMX10 DMX Cable 10m/32.8ft
Q-Wash 575 User Manual 9 8/3/2007 9:10:00 AM

Master/Sl
Often, the setup for Master-Slave
and Standalone operation requires
that the first fixture in the chain be
initialized for this purpose via either
settings in the control panel or DIP-
switches. Secondarily, the fixtures
that follow may also require a slave
setting. Please consult the
“Operating Instructions” section in
this manual for complete instructions
for this type of setup and
configuration.
Hanging Clamp
Note!
Clamp is sold sepa
r
atel
y
.
ave Fixture Linking
1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector
of the first fixture.
2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin
connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then,
proceed to connect from the output as stated above to the input of the following fixture and so on.
Mounting
ORIENTATION
This fixture may be mounted in any position provided there is adequate room for ventilation.
RIGGING
It is important never to obstruct the fan or vents pathway. Mount the
fixture using, a suitable “C” or “O” type clamp. Adjust the angle of the
fixture by loosening both knobs and tilting the fixture. After finding the
desired position, retighten both knobs.
•When selecting installation location, take into consideration lamp replacement
access and routine maintenance.
•Safety cables must always be used.
•Never mount in places where the fixture will be exposed to rain, high
humidity, extreme temperature changes or restricted ventilation.
•A minimum of two mounting points must be used for this fixture.
Q-Wash 575 User Manual 10 8/3/2007 9:10:00 AM

Q-Wash 575 User Manual 11 2007-08-03/09:10
STRUCTIONS
Navigating the Control Panel
Dis
The Control Panel LED Display shows the menu items you select from the menu map on page 12.
for the
selected menu function. To select a menu item, press <ENTER>.
Press the <MODE> button once to activate the control panel. Pressing the <MODE> button again will
<UP> and <DOWN> buttons to
enu function currently
or menu without changing the
4. OPERATING IN
Access control panel functions using the four panel buttons located directly underneath the LCD
play.
Button Function
<MODE> Used to access the menu or to return to a
previous menu option
<ENTER> Used to select and store the current menu
or option within a menu
<UP> Scrolls through menu options in ascending
order
<DOWN> Scrolls through menu options in descending
order
When a menu function is selected, the display will show immediately the first available option
scroll through the different top-level menu options available. Use the
navigate the menu options. Press the <ENTER> button to access the m
displayed or to enable a menu option. To return to the previous option
value, press the <MODE> button.

Menu Map
Q-Wash 575 User Manual 12 2007-08-03/09:10

Control Panel Functions
FUNCTION OPTIONS NOTES
NO/YES Pan Invert (Yes or No)
NO/YES Tilt Invert (Yes or No)
001-497 DMX Channel Address
YES Fixture reset
dn.Co.
Pr6.1
Pr6.2
SLAE
Sou.1
Sou.2
DMX-512 Mode
Automatic Program 1 (when mounted upside down)
Automatic Program 2 (when floor positioned)
Slave Mode
Music Program 1 (when mounted upside down)
Music Program 2 (when floor positioned)
ON
OFF Lamp on Lamp off
X.X Software version
Status Too hot to strike, or no lamp
Status Lamp error
Program Options
MENU
OPTION DESCRIPTION
Automatic – Master Unit (Ceiling-mounted):
Master status for Master-Slave operation and the built in
programs will be triggered automatically. No data link is
required; all fixtures can be set to this mode for Stand-alone
operation.
Sets the fixture to
Automatic – Master Unit (Floor-mounted):
Master status for Master-Slave operation and the built in
programs will be triggered automatically. No data link is
required; all fixtures can be set to this mode for Stand-alone
operation.
Sets the fixture to
Slave Unit: Sets the fixture to run in sync with the Master.
You must set the first fixture in the data link to “Master”
otherwise nothing will happen.
Sound Active – Master Unit (Ceiling-mounted):
to Master status for Master-Slave operation and the built in
programs will be triggered by the sound. No data link is
required; all fixtures can be set to this mode for Stand-alone
operation.
Sets the fixture
Sound Active – Master Unit (Floor-mounted):
Master status for Master-Slave operation and the built in
programs will be triggered by the sound. No data link is
required; all fixtures can be set to this mode for Stand-alone
operation.
Sets the fixture to
DMX: The fixture will be controlled by a DMX signal coming from
a DMX controller. The starting address must be selected.
Q-Wash 575 User Manual 13 2007-08-03/09:10

User Configurations
TO SET THE PAN TO IN NG G:
1) Press <M E> until
VERTI OR NON-INVERTIN
OD is displayed.
2) Use the <UP> and <DOWN> buttons to scroll through the two options. is non-
inverting; is inverting.
TO SET THE TILT TO IN IN
1) Press <M
VERT
DE> until
G OR NON-INVERTING:
Ois displayed.
2) Use the <d <DOW to scroll through the two options.UP> an N> buttons is non-
inverting; is inverting.
Service Functions
TO RESET THE FIXTUR
the <MODE> button until
E:
1) Press is displayed, and then press the <ENTER>
button. The fixture will now reset itself.
TO TURN TH P POW OR OFF:
1) Press the
E LAM ER ON
<MODE> button until is displayed.
P> and <DOWN>
2) Use the <U then press the <ENTER>
button.
buttons to select the desired option and
turns the platform power on; turns the platform power off.
Operation
Stand-Alone Mode (S
This mode allow
Mode.
1) Press <MO
ound-Active, Auto Mode):
s a single unit to run to the beat of the music, or the unit will auto change in Auto
DE/ESC> until is displayed and press the <ENTER> button..
P> and <DOWN> buttons to scroll through until the desired mode is displayed and
ENTER> button.
2) Use the <U
press the <is auto mode ceiling-mounted; is
auto mode floor-mounted; is sound-active ceiling-mounted; is
sound-active floor-mounted.
3) The unit will react to the low frequencies of music via the internal microphone in Sound Active
mode, or the unit will auto change in Auto Mode.
Q-Wash 575 User Manual 14 2007-08-03/09:10

Master/Slave Mode (Master Sound, Master Auto):
w you to link up to 32 units together without a controller.
the DMX connector on the rear
t fixture. For more
information about terminators, see page 9.
This mode will allo
1) Use standard DMX cables to daisy chain your units together via
of the units. For longer cable runs we suggest a terminator at the las
2) Choose a unit to function as the master. Press <MODE/ESC> until is display
3) Use and <DOW yed and
press the <ENTER> button.
ed
on the master unit and press the <ENTER> button..
the <UP> N> buttons to scroll through until the desired mode is displa
is auto mode ceiling-mounted; is
auto mode floor-mounted; is sound-active ceiling-mounted; is
4) DE/ESC> un
sound-active floor-mounted.
Press <MO til is displayed on the slave units. Use the <UP> and
buttons to scroll through until
<DOWN> is displayed and press the <ENTER>
DMX Mode
lled by any un ith
DMX
button.
This mode allows the unit to be contro iversal DMX controller. If you are unfamiliar w
, please read the DMX Primer on page 18.
1) Press <MODE> until is displayed.
ons to locate
2) Use the <UP> and <DOWN> butt and press the <ENTER> button.
3) Press <MODE> until is displayed.
4) <UP> and <D
button.
Use the OWN> buttons to select the desired address and press the <ENTER>
DMX Channel Values
CHANNEL VALUE FUNCTION
1 000 Ù255 128 = halfway pointPan:
2 000 Ù255 Tilt: 128 = halfway point
3 000 Ù255 Pan Fine
4 000 Ù255 Tilt Fine
5 000 Ù255 Vector Speed (Normal > Slow)
6
000 Ù127
240 Ù255
Reset
No Function
Reset
ction
f
No Function
128 Ù139
140 Ù229
230 Ù239
Lamp &
Lamp On &
No Fun
Lamp Of
7
000 Ù017 Color Wheel White (Open)
Q-Wash 575 User Manual 15 2007-08-03/09:10

018 Ù035
036 Ù051 Red Blue
052 Ù071 Green
072 Ù089
090 Ù107
108 Ù127
128 Ù187
188 Ù195
UV
Color Correction: 6000K
Color Correction: 3200K
Rainbow Effect (Slow >
No Function
196 Ù255
fast)
Reverse Rainbow Effect (Slow > Fast)
8 000 Ù255 Cyan (0 – 100%)
9 000 Ù255 Magenta (0 – 100%)
10 000 Ù255 Yellow (0 – 100%)
11 000 Ù255 CMY Speed (Fast > Slow)
12
024 Ù031
056 Ù063
064 Ù071
080 Ù087
4 Ù111
Ù119
120 Ù127
128 Ù135
160 Ù167
184 Ù191
208 Ù215
216 Ù223
Color Macro
ion
Macro 2
3
Macro 6
Macro 7
8
Macro 9
Macro 12
Macro 13
Macro 14
Macro 15
Macro 19
acro 21
Macro 22
Macro 25
Macro 26
acro 27
000 Ù015
016 Ù023
032 Ù039
040 Ù047
048 Ù055
No Funct
Macro 1
Macro
Macro 4
Macro 5
072 Ù079
088 Ù095
096 Ù103
10
112
Macro
Macro 10
Macro 11
136 Ù143
144 Ù151
152 Ù159
Macro 16
Macro 17
Macro 18
168 Ù175
176 Ù183 Macro 20
M
192 Ù199
200 Ù207 Macro 23
Macro 24
224 Ù231
232 Ù239 M
Macro 28
240 Ù247
248 Ù255 Macro 29 Macro 30
13
000 Ù070
071 Ù180
181 Ù255
Effect Wheel
No Function
Beam Shaper
Frost
14 000 Ù255 Zoom: Out > In
15
Ù
Ù
60 Ù191
w > Fast)
be (Slow > Fast)
000 031
032 Ù063
064 095
096 Ù127
128 Ù130
131 Ù159
1
192 Ù223
224 Ù255
Strobe
No Function
Open
Strobe (Slo
Open
No Function
Pulse Strobe (Slow > Fast)
Open
Random Stro
Open
16 n (0 – 100%)
000 Ù255 Dimmer Closed > Ope
Q-Wash 575 User Manual 16 2007-08-03/09:10

General Troubles
Applies to
hooting
Symptom Solution(s)
Lights Foggers
& Snow Controllers Dimmers & Chaser
Auto shut off Check f 9 an thermal switch reset
Beam is very dim or
not bright le y p h v 9
C an optical s stem or replace lam
C eck 220/110 switch for proper setting
Breaker/Fuse keeps
blowing Check total load vice 9
placed on de
Chase is too slow Ch a peed adjustment 999 eck users m nual for s
Device has no power Ch e s.
Ch fuse. (internal and/or external) 999
eck for pow r on Main
eck device’s
Fixture is not
responding Ch p ettings for correct addressing Ch b
Ch s tings
9
eck DMX Di switch s
eck DMX ca les
eck polarity witch set
Fixture is on but
there is no
movement to the
audio
Ma have the correct audio mode on the
con s rovided via ¼” jack, make
sur io ists
Adj e ob
999
ke s e youur
trol switche . If audio p
e a live aud
ust sound s signal ex
nsitivity kn
Lamps cuts off
sporadically Po mp or fixture is overheating. Lam . 9
ssible bad la
p m y be at end of its lifea
Light will not come
on after power failure So e e a cooling off period bef tronics in the fixture can kick start it
aga 10 minutes before powering up
9
me discharg lamps requir
ore the elec
in, wait 5 to
Loss of signal Us c
Ins o
No X eparated from power cables
or b
9999
e only DMX ables
tall terminat r
te: Keep DM cables s
lack lights.
Moves slow Ch v proper setting 9 eck 220/110 switch for
No flash Re , shifted in shipping 9 -install bulb may have
No laser output Bounce mirror m e shifted during shipping,
ea 9
otor may hav
r djust
No light output Ch & brushes for contact
Install bu
al h
9
eck slip ring
lb
l service tec
C nician
Relay will not work Check res i
Ch n 9
et sw tch ns
eck cable co nectio
Remote does not
work Ma n cted to device 99
ke sure con ector is firmly conne
Stand alone mode All h d-alone
fun t require a imply
pow re er into this
mo
9
Chauvet lig
ctions do no
er the fixtu
ting fixtures featuring stan
dditional settings, s
and it will automatically ent
de
If you still em a tions, please contact CHAUVET Technical
Support at the location on the next page.
have a probl fter trying the above solu
Q-Wash 575 User Manual 17 2007-08-03/09:10

Technical Support
d, FL 33020 (U.S.A.)
Support (Email): [email protected]
Telephone: [phone] - (Press 4)
Fax: [phone] - (Attention:
Website: http://www.chauvetlig
PEN
re tion. Channels may be assigned in any manne A
fixture capable of receiving DMX 512 will require one or a number of sequential channels. The user
ust a es the first chan serv in the controller.
There are many different types of DMX controllable fixtures and they all may vary in the total number
a address should be planned in advance. Channels should
never f the fixtures w ng address is
set inc ty ing t same starting
address as long as the intended r son movement or operation. In other words, the
fixture ond exactly the same.
DMX f hain. isy Chain connection is
where ects to the DATA IN of the next fixture. The order in which
the fixtures a w a controller co
each f nd most direct cabling. Connect fixtures
male to female connectors. The
din 3 is Data positive (S+). CHAUVET
e15’) and DMX-1.5 (5’)
e
To ma equently. Usage
and en g frequency. As a general rule, fixtures should
be cleaned at lea ance and can cause
overhe sed mechanic sure to p
fixture bef
Unplu ft b to re ove dust
collec ts. Clean all glass when the fix e is cold with a
mild s nd a soft lint free cotton cloth or lens tissue. Apply
solution to the cloth or tissue and drag dirt and grime to the outside of the lens. Gently polish optical
rfac haze and lint.
The cl s must rrie to
optimize light output. Cleaning frequency depends on the environment in which the f ates:
mp, r accumulation of dirt on the unit’s
optics lways d e parts carefully. - Clean
the ex lea ery 30/60 days
Address: Service Dept.
3000 N 29th Ct, Hollywoo
Service)
hting.com
5. AP DIX
DMX Primer
The are 512 channels in a DMX-512 connec r.
m ssign a starting address on the fixture that indicat nel re ed
of ch nnels required. Choosing a start
overlap. If they do, this will result in erratic operation o hose starti
orrectly. You can however, control multiple fixtures of the same
esult is that of uni
s will be slaved together and all resp
pe us he
ixtures are designed to receive data through a serial Daisy C
nA Da
the DATA OUT of one fixture con
re connected is not important and has no effect on ho
r the easiest a mmunicates to
ixture. Use an order that provides fo
using shielded two conductor t
shiel
carri
wisted pair cable with three pin XLR
connection is pin 1, while pin 2 is Data Negative (S-) and p
s 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (
General Maint nance
intain optimum performance and minimize wear fixtures should be cleaned fr
vironment are contributing factors in determinin
st twice a month. Dust build up reduces light output perform
ating. This can lead to reduced lamp life and increa
ore conducting maintenance. al wear. Be ower off
g fixture from power. Use a vacuum or air compressor and a so rush m
ted on external vents and internal componen
s cleaner or Isopropyl Alcohol a tur
olution of glas
su es until they are free of
eaning of internal and external optical lenses and/or mirror be ca d out periodically
ixture oper
da smoky or particularly dirty surrounding can cause greate
. Clean with soft cloth using normal glass cleaning fluid. - A
ternal optics at least every 20 days. Clean the internal optics at ry th
st ev .
Q-Wash 575 User Manual 18 2007-08-03/09:10

Returns Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
erchandise Authorization Number (RA #). Products
HAUVET and request RA # prior to shipping the
l number, serial number and a brief description of the cause
re, any shipping damage resulting from inadequate
. CHAUVET reserves the right to use its own discretion to
uct(s). As a suggestion, proper UPS packing or double-boxing is always a safe
te: If you are given an RA #, please include the following information on a piece of paper
Claims
refore the damage must be
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and
Technical S
n (406 mm)
Width ............................................................................................................................... 16 in (406 mm)
............................................................................................................ 23 in (584 mm)
............................................................................................................75.8 lbs (34 kg)
...................................................................................... 1224W
° - 34°
°
Bulb ...............................................................................................................................HMI 575W Lamp
t
ket
........16
ORDERING INFORMATION
Q-Wash 575™.....................................................................................................................Q-WASH575
WARRANTY INFORMATION
Warranty.............................................................................................................. 2-year limited warranty
Package must be clearly labeled with a Return M
C
returned without an RA # will be refused. Call
fixture. Be prepared to provide the mode
for the return. Be sure to properly pack fixtu
packaging is the customer’s responsibility
repair or replace prod
method to use.
No inside the box:
1) Your name
2) Your address
3) Your phone number
4) The RA #
5) A brief description of the symptoms
Damage incurred in shipping is the responsibility of the shipper; the
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim
for items such as missing component/part, damage not related to shipping, and concealed damage,
must be made within seven (7) days of receiving merchandise.
pecifications
WEIGHT & DIMENSIONS
Length.............................................................................................................................. 16 i
Height..................
Weight .................
POWER
Operating Voltage (internally selectable) ....................................... 100V, 115V, 208V, 230V - 50/60 Hz
AC input plug...................................................................................................................IEC 60320 C14
Fuse....................................................................................................20mm Glass 15A 250V Fast Blow
Power consumption........................................................................................................................ 720W
Inrush......................................................
PHOTO OPTIC
Beam angle ................................................................................................................................26
Pan...................................................................................................................................................530
Tilt.....................................................................................................................................................280°
Illuminance at 1m ....................................................................................................3,430 fc (36,906 lux)
LAMPS
CONTROL & PROGRAMMING
Data input................................................................................................ locking 3-pin XLR male socke
Data output...........................................................................................locking 3-pin XLR female soc
Data pin configuration ..............................................................................pin 1 shield, pin 2 (-), pin 3 (+)
Protocols........................................................................................................................DMX-512 USITT
DMX Channels .............................................................................................................................
Q-Wash 575 User Manual 19 2007-08-03/09:10