Chauvet Q-Spot 152 User manual

Snapshot
OK on Dimmer
Outdoor OK
Sound Activated
DMX512
Master/Slave
Multitap
Transformer
Replaceable Fuse
User Serviceable
Duty Cycle
Q-Spot 152™
USER MANUAL
Chauvet, 3000 N 29th Ct, Hollywood, FL 33020 U.S.A.
[phone] – [phone]
FAX [phone]
www.chauvetlighting.com

TABLE OF CONTENTS
1. BEFORE YOU BEGIN................................................................................................................................3
WHAT IS INCLUDED......................................................................................................................................... 3
UNPACKING INSTRUCTIONS............................................................................................................................. 3
AC POWER ................................................................................................................................................... 3
CONTACT US................................................................................................................................................. 4
SAFETY INSTRUCTIONS................................................................................................................................... 4
2. INTRODUCTION ........................................................................................................................................ 5
FEATURES..................................................................................................................................................... 5
DMX CHANNEL SUMMARY.............................................................................................................................. 5
PRODUCT OVERVIEW ..................................................................................................................................... 6
3. SETUP........................................................................................................................................................ 7
LAMP............................................................................................................................................................ 7
Lamp Installation............................................................................................................................... 7
Maximizing the life of your lamp.............................................................................................................. 7
Lamp Alignment How-To.................................................................................................................. 8
Fuse Replacement.................................................................................................................................. 8
REPLACING GOBOS........................................................................................................................................ 9
FIXTURE LINKING ........................................................................................................................................... 9
Data Cabling ........................................................................................................................................... 9
DMX Data Cable..............................................................................................................................10
Cable Connectors............................................................................................................................10
3-Pin to 5-Pin Conversion Chart......................................................................................................10
SETTING UP A DMX SERIAL DATA LINK...........................................................................................................11
STAND-ALONE/MASTER/SLAVE FIXTURE LINKING.............................................................................................11
MOUNTING...................................................................................................................................................12
Orientation.......................................................................................................................................12
Rigging ............................................................................................................................................12
4. OPERATING INSTRUCTIONS..................................................................................................................13
NAVIGATING THE CONTROL PANEL .................................................................................................................13
MENU MAP...................................................................................................................................................14
Menu Functions .....................................................................................................................................15
User Configurations ...............................................................................................................................15
To set the pan to inverting or non-inverting: ....................................................................................15
To set the tilt to inverting or non-inverting:.......................................................................................15
To change the color wheel setting:..................................................................................................15
To change the channels setting:......................................................................................................16
Service Functions ..................................................................................................................................16
To reset the fixture:..........................................................................................................................16
To change the Display backlight:.....................................................................................................16
OPERATION..................................................................................................................................................16
Stand-Alone Mode (Sound-Active, Auto Mode): ....................................................................................16
Master/Slave Mode (Master Sound, Master Auto): ................................................................................17
DMX Mode.............................................................................................................................................17
DMX CHANNEL VALUES IN MASTER MODE......................................................................................................18
DMX CHANNEL VALUES IN BASIC MODE.........................................................................................................20
GENERAL TROUBLESHOOTING........................................................................................................................21
TECHNICAL SUPPORT....................................................................................................................................21
5. APPENDIX.................................................................................................................................................22
DMX PRIMER...............................................................................................................................................22
GENERAL MAINTENANCE ...............................................................................................................................23
RETURNS PROCEDURE........................................................................................................................................................................23
CLAIMS ..............................................................................................................................................................................................23
TECHNICAL SPECIFICATIONS ................................................................................................................................................................24
Q-Spot 152 User Manual 2 2007-07-09/17:40

1. BEFORE YOU BEGIN
What is included
¾1 x Q-Spot 152™
¾150W HTI Lamp
¾5 additional metal gobos
¾Power Cord
¾Warranty Card
¾User Manual
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.
AC Power
To determine the power requirements for a particular fixture, see the label affixed to the back plate of
the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating is its average
current draw under normal conditions. All fixtures must be powered directly off a switched circuit and
cannot be run off a rheostat (variable resistor) or
dimmer circuit, even if the rheostat or dimmer channel
is used solely for a 0% to 100% switch. Before applying
power to a fixture, check that the source voltage
matches the fixture’s requirement. Check the fixture or
device carefully to make sure that if a voltage selection
switch exists that it is set to the correct line voltage you
will use.
Figure 1 - AC Voltage Switch
240V230V
208V 115V100V
L
S1
50Hz60Hz
P
owS
wl3
.P
CB
Warning! Verify that the voltage select switch on your unit matches the line voltage applied,
and that the frequency select switch on your unit matches the frequency of the
power in your region. Also verify that you are using the correct fuse value for your
operating voltage. All fixtures must be connected to circuits with a suitable Earth
Ground. Damage to your fixture may occur if these instructions are not followed.
POWER CABLE PIN INTERNATIONAL
BROWN Live L
BLUE Neutral N
YELLOW/GREEN Earth EG (Ground)
OPERATING VOLTAGE MUST USE CORRECT FUSE
120V 3.15A
230V 2A
Q-Spot 152 User Manual 3 2007-07-09/17:40

Contact Us
World Wide
General Information Chauvet Lighting
3000 North 29th Court
Hollywood, FL 33020
voice: 954.929.1115
fax: [phone]
toll free: 800.762.1084
Technical Support Chauvet Lighting
3000 North 29th Court
Hollywood, FL 33020
voice: 954.929.1115 (Press 4)
fax: [phone] (Attention: Service)
World Wide Web www.chauvetlighting.com
Safety Instructions
Please read these instructions carefully, which includes important
information about the installation, usage and maintenance of this
product.
•Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Always make sure that you are connecting to the proper voltage, and that the line voltage you are
connecting to is not higher than that stated on the decal or rear panel of the fixture.
•This product is intended for indoor use only!
•To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no
flammable materials close to the unit while operating.
•The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Always disconnect from power source before servicing or replacing lamp or fuse and be sure to
replace with same lamp source.
•Secure fixture to fastening device using a safety chain. Never carry the fixture solely by its head. Use
its carrying handles.
•Maximum ambient temperature (Ta) is 95°F (35°C). Do not operate fixture at temperatures higher
than this.
•In the event of a serious operating problem, stop using the unit immediately. Never try to repair the
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•Don’t connect the device to a dimmer pack.
•Make sure the power cord is never crimped or damaged.
•Never disconnect the power cord by pulling or tugging on the cord.
•Avoid direct eye exposure to the light source while it is on.
Caution! There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service,
please contact CHAUVET at: 954-929-1115.
Q-Spot 152 User Manual 4 2007-07-09/17:40

2. INTRODUCTION
Features
•8 or 12-channel DMX-512 moving yoke
•Pan: 540° / tilt: 270°
•Variable strobe/shutter/dimmer
•Color wheel
9 colors + white
Rainbow color spin at variable speeds
•Rotating gobo wheel
7 interchangeable rotating + open
4 metal, 3 glass installed
Additional free gobos: 5 metal
Rotating gobo wheel spin at variable speeds
Gobo Bounce™
•Remote fixture reset & vector speed channel
•Built-in effect macros via DMX (gobo, gobo rotation, color, strobe)
Additional Features
•Built-in automated programs via master/slave
•Built-in sound-active programs via master/slave
•User-selectable basic or advanced operating modes
•Micro-stepping motors
•LCD display
•Thermal switch
•Fan cooled
DMX Channel Summary
CHANNEL FUNCTION (ADVANCED MODE) FUNCTION (BASIC MODE)
1 Pan Pan
2 Tilt Tilt
3 Fine pan Color wheel
4 Fine tilt Gobo wheel
5 Vector speed Gobo rotate
6 Color wheel Strobe
7 Gobo wheel Dimmer
8 Gobo rotate Automatic and reset
9 Strobe
10 Dimmer
11 Automatic and reset
12 Effect
Q-Spot 152 User Manual 5 2007-07-09/17:40

Product Overview
Head
Arm
Base
Control
Panel
Focus
Adjust
DMX Input
Easy Controller Input
(sold separately,
release date TBA)
DMX Output
IEC Power
Connector
Voltage Select
Switch (Internal)
Power
Switch
Microphone
Q-Spot 152 User Manual 6 2007-07-09/17:40

3. SETUP
Lamp
You will need to install a lamp prior to the initial operation of the fixture. A 150W HTI lamp is included.
Warning! When replacing the lamp, please wait 15 minutes after powering down to allow the
unit to cool down! Always disconnect from main power prior to lamp replacement.
Do not touch the envelope (glass area) of the bulb with bare hands. If this happens, clean the lamp
with alcohol and wipe it with a lint free cloth before installation.
LAMP INSTALLATION
1. Remove screws labeled (S1) and pull out lamp socket
plate.
A B
C
S1
S2
2. If replacing the lamp, remove old lamp first.
3. Holding the new lamp by its base, align the pins on the
lamp with the small hole in the socket and insert the
lamp squarely until the retaining clips on the lamp s
secure the lamp tightly. ocket
4. Clean the glass/envelope of the bulb with an alcohol
wipe or equivalent.
5. Holding the lamp socket plate, insert the tip of the lamp
into the fixture with extreme care. Navigate the lamp all
the way until it reaches the reflector and the lamp base
plate touches the bottom plate of the fixture.
6. Align the screw holes and fasten the screws back onto
the lamp socket plate.
7. Turn the fixture on and adjust the lamp alignment
screws (S2) until the brightest most even area of the
beam is in the center of your spot. It may be necessary
for you to use a controller in order to command the
fixture to display a white beam on a flat surface with no
colors.
Maximizing the life of your lamp
To ensure the longest and most efficient use of the lamp always wait
between 10 and 15 minutes before re-applying power after a shutdown.
Failure to do so could result in premature aging of the lamp and failure to the
electronics that drive it.
Never turn off the power to the unit while the lamp is striking. Always wait 15
minutes after powering on the fixture before powering down. Turning off the lamp
during striking may permanently damage the lamp.
Q-Spot 152 User Manual 7 2007-07-09/17:40

LAMP ALIGNMENT HOW-TO
Often, after a new installation of a lamp, you will find
that there is an uneven field of light or what is referred
to as a hot spot. This is due to the most intense point
of the lamp source not being positioned optimally
within the reflector.
Lamp Alignment Screws
A B
CS2
There are three lamp alignment screws provided at the
base of the projector head. Turning these screws allow
you to optimize the projection quality of the spot as
well as the overall intensity of the beam.
1. Project a white spot against any flat surface.
Preferably the surface should be white or pastel in
color.
2. Turning the lamp alignment screws, try to position
the hot spot in the center of the beam as best as
possible. This could require many attempts on your
part.
3. Once the hot spot is in the center of the spot, do
your best to turn all screws equally as to affect
movement up or down within the reflector.
4. As you move in and out of optimum lamp focus, you will see the hot spot either gets wider or
narrower. The goal is to either totally diminish the hot spot by having it widen and spread across
the entire spot or moving the hot spot so that it covers as much of the beam spot area as
possible.
Disconnect the power cord before replacing a fuse and always
replace with the same type fuse.
Fuse Replacement
The fuse is located
inside this
compartment.
Remove using a flat
head screwdriver.
With a flat head screwdriver wedge the fuse holder out of its housing. Remove the damaged fuse
from its holder and replace with exact same type fuse. Insert the fuse holder back in its place and
reconnect power.
Q-Spot 152 User Manual 8 2007-07-09/17:40

Replacing Gobos
Figure A
Figure B
1) Remove the four screws indicated in
figure A to remove the bottom of the
head.
2) Remove the glue from the gobo u
tweezers. sing
3) Remove the retaining spring from the
gobo (figure B).
4) Remove the existing gobo, and
replace with a new gobo.
5) Replace the retaining spring.
6) If desired, add three small dabs of
high-temperature silicone glue to the
retaining spring.
7) Repeat steps 4-6 as many times as
necessary to replace all desired
gobos.
8) Replace the bottom cover and
retighten the four screws removed in
step 1.
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller
or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The
combined number of channels required by all the fixtures on a serial data link determines the number
of fixtures the data link can support.
Important: Fixtures on a serial data link must be daisy chained in one single line. To comply with the EIA-485
standard no more than 32 devices should be connected on one data link. Connecting more than 32
fixtures on one serial data link without the use of a DMX optically-isolated splitter may result in
deterioration of the digital DMX signal.
Maximum recommended serial data link distance: 500 meters (1640 ft.)
Maximum recommended number of fixtures on a serial data link: 32 fixtures
Data Cabling
To link fixtures together you must obtain data cables. You can purchase CHAUVET-certified DMX
cables directly from a dealer/distributor or construct your own cable. If you choose to create your own
cable please use data-grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.
Q-Spot 152 User Manual 9 2007-07-09/17:40

DMX DATA CABLE
Use a Belden© 9841 or equivalent cable which meets the specifications for EIA RS-485 applications.
Standard microphone cables cannot transmit DMX data reliably over long distances. The cable will
have the following characteristics:
2-conductor twisted pair plus a shield
Maximum capacitance between conductors – 30 pF/ft.
Maximum capacitance between conductor and shield – 55 pF/ft.
Maximum resistance of 20 ohms / 1000 ft.
Nominal impedance 100 – 140 ohms
CABLE CONNECTORS
Cabling must have a male XLR connector on one end and a female XLR connector on the other end.
can cause a ground loop, and your fixture may perform erratically. Test cables with an ohm meter to r.
3-PIN TO 5-PIN CONVE
pin DMX output connector, you will need to use a 5 pin to 3 pin adapter.
CHAUVET Model No: DMX5M, or DMX5F.
3PIN TO 5PIN C
Conductor 3 Pin Female (output) 5 Pin Male (Input)
CO
MM
O
N
DMX
+
DMX -
INPUT OUTPUT
1
3
2
1
3
2
1
3
2
Resistance 120
ohm 1/4w between
pin 2 (DMX -) and
pin 3 (DMX +) of
the last fixture.
Termination reduces signal errors and
to avoid signal transmission problems
and interference, it is always
advisable to connect a DMX signal
terminator.
DMX connector configuration
CAUTION Do not allow contact between the common and the fixture’s chassis ground. Grounding the common
verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each othe
RSION CHART
Note! If you use a controller with a 5
The chart below details a proper cable conversion:
ONVERSION CHART
Grou hieldnd/S Pin 1 Pin 1
Data ( - ) signal Pin 2 Pin 2
Data ( + ) signal Pin 3 Pin 3
Do not use Do not use
Do not use Do not use
Q-Spot 152 User Manual 10 2007-07-09/17:40

Setting up a DMX Serial Data Link
1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector
of the controller.
2. Connect the end of the cable coming from the controller which will have a (female) 3 pin connector
to the input connector of the next fixture consisting of a (male) 3 pin connector.
3. Then, proceed to connect from the output as stated above to the input of the following fixture and
so on.
CHAUVET Certified DMX Data Cables
Order Code Description
DMX1.5 DMX Cable 1.5m/4.9ft
DMX4.5 DMX Cable 4.5m/14.8ft
DMX10 DMX Cable 10m/32.8ft
This drawing provides a
general illustration of the
DMX Input/Output panel of
a lighting fixture.
Universal DMX Controller
Continue the link
Stand-Alone/Master/Slave Fixture Linking
1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector
of the first fixture.
2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin
connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then,
proceed to connect from the output as stated above to the input of the following fixture and so on.
Often, the setup for Master-Slave
and Standalone operation requires
that the first fixture in the chain be
initialized for this purpose via either
settings in the control panel or DIP-
switches. Secondarily, the fixtures
that follow may also require a slave
setting. Please consult the
“Operating Instructions” section in
this manual for complete instructions
for this type of setup and
configuration.
Q-Spot 152 User Manual 11 2007-07-09/17:40

Mounting
ORIENTATION
This fixture may be mounted in any position provided there is adequate room for ventilation.
RIGGING
Hanging Clamp
It is important never to obstruct the fan or vents pathway. Mount the
fixture using, a suitable “C” or “O” type clamp. Adjust the angle of the
fixture by loosening both knobs and tilting the fixture. After finding the
desired position, retighten both knobs.
•When selecting installation location, take into consideration lamp
replacement access and routine maintenance.
•Safety cables should always be used. Note!
Clamp is sold separatel
•Never mount in places where the fixture will be exposed to rain, high
humidity, extreme temperature changes or restricted ventilation.
y
.
Safety cable attachment points
Clamp attachment point
Clamp attachment point
Q-Spot 152 User Manual 12 2007-07-09/17:40

4. OPERATING INSTRUCTIONS
Navigating the Control Panel
Access control panel functions using the four panel buttons located directly underneath the LCD
Display.
MENU ENTER DOWN UP
Button Function
<MENU> Used to access the menu or to return to a
previous menu option
<UP> Scrolls through menu options in ascending
order
<DOWN> Scrolls through menu options in descending
order
<ENTER> Used to select and store the current menu
or option within a menu
The Control Panel LCD Display shows the menu items you select from the menu map on page 13.
When a menu function is selected, the display will show immediately the first available option for the
selected menu function. To select a menu item, press <ENTER>.
Press the <MENU> button repeatedly until MENU appears on the top line of the display. This is the
top of the menu map. What appears on the bottom line of the display is one of the four choices in the
menu map. Use the <UP> and <DOWN> buttons to navigate the menu map and menu options. Press
the <ENTER> button to access the menu function currently displayed or to enable a menu option. To
return to the previous option or menu without changing the value, press the <MENU> button.
Q-Spot 152 User Manual 13 2007-07-09/17:40

Menu Map
Menu 1-Address
When navigating the menu:
Use the “UP” button to move up.
Use the “DOWN” button to move down.
Use the “ENTER” button to move right.
Use the “MENU” button to move up.
2-Reset
3-Operation
4-Display
5-Pan
6-Tilt
7-Color
8-Channels
9-Info
1-Address
select: 001
2-Reset
select: No
2-Reset
select: Yes
3-Operation
select: DMX
3-Operation
select: Auto1
3-Operation
select: Random
3-Operation
select: Sound1
3-Operation
select: Slave
3-Operation
select: Auto2
3-Operation
select: Sound2
4-Display
select: 60 close
4-Display
select: Bright
5-Pan
select: Normal
5-Pan
select: Reverse
6-Tilt
select: Reverse
6-Tilt
select: Normal
7-Color
select: Linear
7-Color
select: Step
8-Channels
select: Advanced
8-Channels
select: Basic
Q-Spot 152 User Manual 14 2007-07-09/17:40

Menu Functions
MENU
OPTION DESCRIPTION
1-Address Set the DMX address for the fixture.
2-Reset Reset the fixture.
3-Operation Select operating mode: DMX, Auto 1, Auto 2, Music 1, Music 2, Slave, or
Random. Auto and Music modes set the fixture to Master/Stand-alone mode.
4-Display Change whether display backlight turns off after 60 seconds or not.
5-Pan Pan normal or inverted.
6-Tilt Tilt normal or inverted.
7-Color Set the color wheel to linear control (split colors), or snap to color.
8-Channels Set the fixture to 12 channel (Advanced mode) or 9 channel (Basic mode)
operation.
9-Info Software version
User Configurations
TO SET THE PAN TO INVERTING OR NON-INVERTING:
1) Press the <MENU> button.
2) Scroll up or down until <5-Pan> is displayed.
3) Press <ENTER>.
4) Press up or down until <select: Normal> or <select: Reverse> is displayed.
5) Press <ENTER>.
TO SET THE TILT TO INVERTING OR NON-INVERTING:
1) Press the <MENU> button.
2) Scroll up or down until <6-Tilt> is displayed.
3) Press <ENTER>.
4) Press up or down until <select: Normal> or <select: Reverse> is displayed.
5) Press <ENTER>.
TO CHANGE THE COLOR WHEEL SETTING:
1) Press the <MENU> button.
2) Scroll up or down until <7-Color> is displayed.
3) Press <ENTER>.
4) Press up or down until <select: Step> or <select: Linear> is displayed. “Step” snaps to colors,
“Linear” allows split colors.
5) Press <ENTER>.
Q-Spot 152 User Manual 15 2007-07-09/17:40

TO CHANGE THE CHANNELS SETTING:
1) Press the <MENU> button.
2) Scroll up or down until <8-Channels> is displayed.
3) Press <ENTER>.
4) Press up or down until <select: Basic> or <select: Advanced> is displayed. Basic uses 9
channels, Advanced uses 12 channels.
5) Press <ENTER>.
Service Functions
TO RESET THE FIXTURE:
1) Press the <MENU> button.
2) Scroll up or down until <2-Reset> is displayed.
3) Press <ENTER>.
4) Press up or down until <select: Yes> is displayed.
5) Press <ENTER>.
TO CHANGE THE DISPLAY BACKLIGHT:
1) Press the <MENU> button.
2) Scroll up or down until <4-Display> is displayed.
3) Press <ENTER>.
4) Press up or down until <select: 60 close> or <select: Bright> is displayed. 60 close turns the
backlight off after 60 seconds; Bright leaves the backlight on always.
5) Press <ENTER>.
Operation
Stand-Alone Mode (Sound-Active, Auto Mode):
This mode allows a single unit to run to the beat of the music, or the unit will auto change in Auto
Mode.
1) Press the <MENU> button.
2) Scroll up or down until <3-Operation> is displayed.
3) Press <ENTER>.
4) Press up or down until <select: Auto1>, <select: Auto2>, <select: Music1>, <select:
Music1>, or <select: Random> is displayed.
5) Press <ENTER>.
6) The unit will react to the low frequencies of music via the internal microphone in Sound Active
mode, or the unit will auto change in Auto Mode. In Random mode, the unit will periodically
change between auto and sound-active modes.
Q-Spot 152 User Manual 16 2007-07-09/17:40

Master/Slave Mode (Master Sound, Master Auto):
This mode will allow you to link up to 32 units together without a controller.
1) Use standard DMX cables to daisy chain your units together via the DMX connector on the rear
of the units. For longer cable runs we suggest a terminator at the last fixture. For more
information about terminators, see page 10.
2) Choose a unit to function as the Master. This unit must be the first unit in the line.
3) Press the <MENU> button.
4) Scroll up or down until <3-Operation> is displayed.
5) Press <ENTER>.
6) Press up or down until <select: Auto1>, <select: Auto2>, <select: Music1>, <select:
Music1>,or <select: Random> is displayed.
7) Press <ENTER>.
8) Chain the units together using DMX cable.
9) On the slave units, press the <MENU> button.
10) Scroll up or down until <3-Operation> is displayed.
11) Press up or down until <select: Slave> is displayed.
12) Press <ENTER>.
13) The units will react to the low frequencies of music via the internal microphone in Sound-Active
mode, or the unit will auto change in Auto Mode. In Random mode, the unit will periodically
change between auto and sound-active modes.
DMX Mode
This mode allows the unit to be controlled by any universal DMX controller. If you are unfamiliar with
DMX, please read the DMX Primer on page 22.
1) Press the <MENU> button.
2) Scroll up or down until <3-Operation> is displayed.
3) Press <ENTER>.
4) Press up or down until <select: DMX> is displayed.
5) Press <ENTER>.
Q-Spot 152 User Manual 17 2007-07-09/17:40

DMX Channel Values in Advanced Mode
CHANNEL VALUE FUNCTION
1 000 Ù255 Pan
2 000 Ù255 Tilt
3 000 Ù255 Fine pan
4 000 Ù255 Fine tilt
5 000 Ù255 Vector Speed: (Normal > Slow)
6
000 Ù014
015 Ù029
030 Ù044
045 Ù059
060 Ù074
075 Ù089
090 Ù104
105 Ù119
120 Ù134
135 Ù149
150 Ù255
Color Wheel
White (Open)
Red
Orange
Yellow
Green
Blue
Magenta
Pink
Cyan
UV
Color scroll: Slow > Fast
7
000 Ù009
010 Ù019
020 Ù029
030 Ù039
040 Ù049
050 Ù059
060 Ù069
070 Ù079
080 Ù099
100 Ù119
120 Ù139
140 Ù159
160 Ù179
180 Ù199
200 Ù219
220 Ù255
Gobo Wheel
Open
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Shaking Gobo 1
Shaking Gobo 2
Shaking Gobo 3
Shaking Gobo 4
Shaking Gobo 5
Shaking Gobo 6
Shaking Gobo 7
Gobo scroll: Fast > Slow
8
000 Ù002
003 Ù006
007 Ù128
129 Ù132
133 Ù136
137 Ù140
141 Ù255
Gobo Rotation
Stop
Rotate CW slow
Rotate CW (slow > fast)
Rotate CW fast
Stop
Rotate CCW slow
Rotate CCW (slow > fast)
9
000 Ù009
019 Ù069
070 Ù079
080 Ù089
090 Ù149
150 Ù159
160 Ù169
170 Ù252
253 Ù255
Strobe
Open
Strobe: Slow > Fast
Strobe: Fastest
Open
Random strobe effect: Slow > Fast
Random strobe effect: Fastest
Open
Strobe: Slow > Fast
Strobe: Fastest
10 000 Ù014
015 Ù255
Dimmer
Closed
Closed > Open (0 > 100%)
11
000 Ù029
030 Ù059
060 Ù089
090 Ù127
Automatic & Reset
DMX
Automatic 1
Automatic 2
No effect
Q-Spot 152 User Manual 18 2007-07-09/17:40

128 Ù139
140 Ù169
170 Ù199
200 Ù229
230 Ù255
Reset
No effect
Sound Active 1
Sound Active 2
Random
12
000 Ù009
010 Ù019
020 Ù029
030 Ù039
040 Ù049
050 Ù059
060 Ù069
070 Ù079
080 Ù089
090 Ù099
100 Ù109
110 Ù119
120 Ù129
130 Ù139
140 Ù149
150 Ù159
160 Ù169
170 Ù179
180 Ù189
190 Ù199
200 Ù209
210 Ù219
220 Ù229
230 Ù239
240 Ù249
250 Ù255
Effect
No Effect
Effect 1
Effect 2
Effect 3
Effect 4
Effect 5
Effect 6
Effect 7
Effect 8
Effect 9
Effect 10
Effect 11
Effect 12
Effect 13
Effect 14
Effect 15
Effect 16
Effect 17
Effect 18
Effect 19
Effect 20
Effect 21
Effect 22
Effect 23
Effect 24
Effect 25
Q-Spot 152 User Manual 19 2007-07-09/17:40

DMX Channel Values in Basic Mode
CHANNEL VALUE FUNCTION
1 000 Ù255 Pan
2 000 Ù255 Tilt
3
000 Ù014
015 Ù029
030 Ù044
045 Ù059
060 Ù074
075 Ù089
090 Ù104
105 Ù119
120 Ù134
135 Ù149
150 Ù255
Color Wheel
White (Open)
Red
Orange
Yellow
Green
Blue
Magenta
Pink
Cyan
UV
Color scroll: Slow > Fast
4
000 Ù009
010 Ù019
020 Ù029
030 Ù039
040 Ù049
050 Ù059
060 Ù069
070 Ù079
080 Ù099
100 Ù119
120 Ù139
140 Ù159
160 Ù179
180 Ù199
200 Ù219
220 Ù255
Gobo Wheel
Open
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Shaking Gobo 1
Shaking Gobo 2
Shaking Gobo 3
Shaking Gobo 4
Shaking Gobo 5
Shaking Gobo 6
Shaking Gobo 7
Gobo scroll: Fast > Slow
5
000 Ù002
003 Ù006
007 Ù128
129 Ù132
133 Ù136
137 Ù140
141 Ù255
Gobo Rotation
Stop
Rotate CW slow
Rotate CW (slow > fast)
Rotate CW fast
Stop
Rotate CCW slow
Rotate CCW (slow > fast)
6
000 Ù009
019 Ù069
070 Ù079
080 Ù089
090 Ù149
150 Ù159
160 Ù169
170 Ù252
253 Ù255
Strobe
Open
Strobe: Slow > Fast
Strobe: Fastest
Open
Random strobe effect: Slow > Fast
Random strobe effect: Fastest
Open
Strobe: Slow > Fast
Strobe: Fastest
7 000 Ù014
015 Ù255
Dimmer
Closed
Closed > Open (0 > 100%)
8
000 Ù029
030 Ù059
060 Ù089
090 Ù127
128 Ù139
140 Ù169
170 Ù199
200 Ù229
230 Ù255
Automatic & Reset
DMX
Automatic 1
Automatic 2
No effect
Reset
No effect
Sound Active 1
Sound Active 2
Random
Q-Spot 152 User Manual 20 2007-07-09/17:40