Chauvet Intimidator COLOR LED User manual

User Manual

Page 2 of 18 Intimidator™ Spot LED 150 User Manual Rev. 8
TABLE OF CONTENTS
1. Before You Begin................................................................................3
What Is Included ...........................................................................................3
Unpacking Instructions..................................................................................3
Claims...................................................................................................................3
Text Conventions ..........................................................................................3
Symbols........................................................................................................3
Disclaimer.....................................................................................................3
Product at a Glance.......................................................................................4
Safety Notes .................................................................................................4
2. Introduction.........................................................................................5
Product Overview..........................................................................................5
Product Dimensions......................................................................................6
3. Setup...................................................................................................7
AC Power......................................................................................................7
Fuse Replacement.................................................................................................7
Power Linking........................................................................................................7
Mounting.......................................................................................................8
Orientation.............................................................................................................8
Rigging..................................................................................................................8
4. Operation ............................................................................................9
Control Panel Operation................................................................................9
Menu Map.....................................................................................................9
Configuration (DMX)....................................................................................10
Starting Address ..................................................................................................10
DMX Personalities................................................................................................10
DMX Channel Assignments and Values.......................................................11
11-CH..................................................................................................................11
6-CH....................................................................................................................13
Configuration (Standalone)..........................................................................14
Sound-Active Mode..............................................................................................14
Automatic Mode...................................................................................................14
Manual Pan/Tilt Operation....................................................................................14
Pan/Tilt Angle Range...........................................................................................14
Display Orientation...............................................................................................15
Master/Slave Mode..............................................................................................15
Reset Software ....................................................................................................15
5. Technical Information ......................................................................16
Product Maintenance ..................................................................................16
6. Technical Specifications..................................................................17
Returns.......................................................................................................18
Contact Us..................................................................................................18

Intimidator™ Spot LED 150 User Manual Rev. 8 Page 3 of 18
1.BEFORE YOU BEGIN
What Is
Included
•Intimidator™ Spot LED 150
•Hanging Bracket with Mounting
Hardware
•Power Cord
•Warranty Card
•Quick Reference Guide
Unpacking
Instructions
Immediately upon receipt, carefully unpack the product
and check the container to make
sure you have received all the parts indicated above in good condition.
Claims
If the container or the material inside the container (the product and
included
accessories) appear damaged from shipping, or show signs of mishandling,
upon receipt
notify the carrier immediately, not CHAUVET®.
Failure to do so in a timely manner may
invalidate your claim with the carrier. In addition, keep the container and all the pa
cking
material for inspection.
For other issues such as missing components or parts, damage not related to shipping,
or concealed damage, file a claim with CHAUVET® within 7 days of receiving the
merchandise.
Text
Conventions
Convention
Meaning
1~512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Symbol
Meaning
Critical installation, configuration, or operation information. Failure
to comply could make the product not work, damage it, and harm
the user.
Important installation or configuration information. Failure to
comply with this information may prevent the product from
functioning correctly.
Useful information.
Disclaimer
The information and specifications contained in this document are subject to change
without notice. CHAUVET® assumes no responsibility or liability for any errors or
omissions that may appear in this manual.
CHAUVET® reserves the right to update the
existing document or to create a new document to correct any errors or omissions.
You can download the latest version of this document from www.chauvetlighting.com.
© Copyright 2013 CHAUVET®. All rights reserved.
Printed in P.R.C. Electronically published by CHAUVET®
in the United States of
America.
Author Date Editor Date
A. Leon 06/11/13 T. Yeago 06/17/13

Page 4 of 18 Intimidator™ Spot LED 150 User Manual Rev. 8
Product at a
Glance
Use on Dimmer
x
Auto Programs
P
Outdoor Use
x
Auto-ranging Power Supply
P
Sound-Activated
P
Replaceable Fuse
P
DMX
P
User-Serviceable
x
Master/Slave
P
Duty Cycle
x
Safety Notes
Please read the following Safety Notes carefully before working with the product. The
Notes include important safety information about installation, usage, and maintenance.
•This product is not intended for permanent installation.
•Always connect the product to a grounded circuit to avoid the risk of electrocution.
•Always disconnect the product from the power source before cleaning or replacing
the fuse.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power cord by pulling or tugging on the cord.
•If mounting the product overhead, always secure to a fastening device using a
safety cable.
•Make sure there are no flammable materials close to the product when operating.
•
Do not touch the product’s housing when operating because it may be very hot.
•Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
•The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
•Always install the product in a location with adequate ventilation, at least 20 in
(50 cm) from adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Never connect the product to a dimmer.
•Make sure to replace the fuse with another of the same type and rating.
•Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket or the handles.
•The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate the
product at higher temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center.
•Keep this User Manual. If you sell the product to another user, be sure that they
also receive this document.

Intimidator™ Spot LED 150 User Manual Rev. 8 Page 5 of 18
2.INTRODUCTION
Product Overview
Power In/Out
Fuse Holder
DMX In/Out
LED Display Cooling Fan
Moving Yoke
Moving Head
Adjustable Lens

Page 6 of 18 Intimidator™ Spot LED 150 User Manual Rev. 8
Product Dimensions

Intimidator™ Spot LED 150 User Manual Rev. 8 Page 7 of 18
3.SETUP
AC Power
The Intimidator™ Spot LED 150 has an auto-
ranging power supply and it can work with
an input voltage range of 100~240 VAC, 50/60 Hz.
To determine the product’s power requirements (circuit breaker, power outlet, and
wiring), use the current value listed on the label affixed to the product’s back panel, or
refer to the product’s specifications chart. The listed current rating indicates the
product’s average current draw under normal conditions.
Always connect the product to a protected circuit
(circuit breaker or fuse). Make
sure the product has
an appropriate electrical ground to avoid the risk of
electrocution or fire.
Never connect the product to
a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0~100% switch.
Disconnect the product from power before replacing the fuse.
Fuse
Replacement
1. Using a flat-head screwdriver, unscrew the fuse holder from the back of the product.
2. Remove the blown fuse from the holder and replace with a fuse of the exact same
type and rating.
3. Insert the fuse holder back in place, re-tighten, and reconnect power.
Power Linking
The product provides power linking via the Edison outlet located in the back
of the unit.
Please see the diagram below for further explanation.
Power Linking
Diagram
You can power link up to 6 Intimidator™ Spot LED 150 unit
s on 120 VAC or up to
12 Intimidator™ Spot LED 150 units on 230 VAC.
The power linking diagram shown above corresponds to the North American
version of the product ONLY! If using the product
in other markets, you must
consult with the local CHAUVET® distributor as power linking connectors and
requirements may differ in your area.
1st Product
2nd Product
3rd Product
Other products

Page 8 of 18 Intimidator™ Spot LED 150 User Manual Rev. 8
Mounting
Before mounting the product, read and follow the Safety Notes.
Orientation
The Intimidator™ Spot LED 150
may be mounted in any position; however, make sure
adequate ventilation is provided around the product.
Rigging
•Before deciding on a location, always make sure there is easy access to the product
for maintenance and programming purposes.
•Make sure that the structure or surface onto which you are mounting the product
can support the product’s weight. See the Technical Specifications section of this
manual for weight information.
•When mounting the product overhead, always use a safety cable.
Mount the
product securely to a rigging point, whether an elevated platform or a truss.
•When rigging the product onto a truss, you should use a mounting clamp of
appropriate weight capacity. The bracket has 13 mm holes, which are
appropriate
for this purpose.
•When power linking multiple products, you must always consider the length of the
power linking cable and mount the products close enough for the cable to reach.
•The rubber feet also serve as floor supports/allow for
surface mounting. When
mounting the product on the floor, make sure that the product and cables are away
from people and vehicles.
Mounting Diagram
Rubber Feet (x4)
Safety Loop
Attachment
Point
Bracket
Attachement (x2)

Intimidator™ Spot LED 150 User Manual Rev. 8 Page 9 of 18
4.OPERATION
Control Panel
Operation
To access the control panel functions, use the four buttons located underneath the
display.
Button Function
<MODE/ESC> Press to find an operation mode or to back out of the current menu
option
<UP>
Press to scroll up the list of options or to find a higher value
<DOWN> Press to scroll down the list of options or to find a lower value
<ENTER>
Press to activate a menu option or a selected value
Menu Map
Mode
Programming Steps
Description
DMX Mode 001-512 Sets the DMX starting address
Operating
Mode
SLAv (Son) Slave operating mode
NASL (SLoU)
Automatic mode, slow program
NAFA (FASt)
Automatic mode, fast program
NStS (SrUn) Sound-Active mode
Pan
Normal Pan
PAn
Normal Pan operation
Inverse Pan r PAn Inverse Pan operation
Tilt Normal Tilt tiL Normal Tilt operation
Inverse Tilt
r tiL
Inverse Tilt operation
Display
Normal
Display diS Change the LCD display text position
Inverse
Display
r diS
Channel Mode
11-Channel
Mode 11CH Selects the DMX personality
6-Channel
Mode 6CH
Manual Pan
Range
Pan 540 PA54 Select Pan angle range
Pan 360
PA36
Pan 180 PA18
Manual Tilt
Range
Tilt 270 Ti27 Select Tilt angle range
Tilt 180
Ti18
Tilt 90
Ti 9
Reset rESt Resets fixture
Load LoAd Load factory defaults

Page 10 of 18 Intimidator™ Spot LED 150 User Manual Rev. 8
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
3. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
Starting Address
When selecting a starting DMX address, always consider the number of DMX channels
the selected DMX mode uses. If you choose a starting address that is too high, you could
restrict the access to some of the product’s channels.
The Intimidator™ Spot LED 150 uses up to 11 DMX channels in its 11-
channel DMX
mode, which defines the highest configurable address to 502.
If unfamiliar with the DMX, download the DMX Primer from www.chauvetlighting.com.
To select the starting address, do the following:
1. Press <MODE/ESC> repeatedly until 001 shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select the starting address.
4. Press <ENTER>.
DMX
Personalities
The Intimidator™ Spot LED 150 has two DMX personalities, a 6-
channel personality and
an 11-channel personality.
To choose which DMX personality to use, follow the steps below:
1. Press <MODE/ESC> repeatedly until either 11CH (to choose the 11-channel
personality) or 6CH (to choose the 6-channel personality) shows on the display.
2. Press <ENTER>.

Intimidator™ Spot LED 150 User Manual Rev. 8 Page 11 of 18
DMX Channel Assignments and Values
11-CH
Channel Function Value Setting
1
Pan
000 ó255
0–540°
2
Tilt
000 ó255
0–270°
3
Fine Pan
000
ó
255
Fine control of panning
4
Fine Tilt
000 ó255
Fine control of tilting
5
Speed
000 ó255
Pan/Tilt speed (fast to slow)
6 Color Wheel
000 ó005
White
006 ó011
Yellow
012 ó017
Magenta
018 ó023
Green
024 ó029
Red
030 ó035
Cyan
036 ó041
Orange
042
ó
047
Blue
048 ó053
Light Green
054 ó063
Amber
064 ó069
White + Yellow
070 ó075
Yellow + Magenta
076 ó081
Magenta + Green
082 ó087
Green + Red
088 ó093
Red + Cyan
094 ó099
Cyan + Orange
100 ó105
Orange + Blue
106 ó111
Blue + Light Green
112 ó117
Light Green + Amber
118 ó127
Amber + White
128 ó191
Color cycling rainbow with increasing speed
192 ó255
Reverse color cycling rainbow with increasing
speed
7 Shutter
000 ó003
Blackout
004 ó007
Open
008 ó215
Strobe (0–20 Hz)
216 ó255
Open
8
Dimmer
000 ó255
0–100%

Page 12 of 18 Intimidator™ Spot LED 150 User Manual Rev. 8
11-CH
(cont.)
Channel Function Value Setting
9 Gobo Wheel
064 ó071
Gobo 9 shake, from slow to fast
072 ó079
Gobo 8 shake, from slow to fast
080 ó085
Gobo 7 shake, from slow to fast
086 ó091
Gobo 6 shake, from slow to fast
092 ó097
Gobo 5 shake, from slow to fast
098 ó103
Gobo 4 shake, from slow to fast
104 ó109
Gobo 3 shake, from slow to fast
110 ó115
Gobo 2 shake, from slow to fast
116 ó121
Gobo 1 shake, from slow to fast
122 ó127
Open
128 ó191
Cycle effect with increasing speed
192 ó255
Reverse cycle effect with increasing speed
10 Control Functions
000 ó007
No function
008 ó027
Blackout while pan/tilt moving
028 ó047
Blackout while moving gobo wheel
048 ó067
Disable blackout while pan/tilt/moving gobo wheel
068 ó087
Blackout while moving color wheel
088 ó107
Disable blackout while pan/tilt/moving color wheel
108 ó127
Disable blackout while moving gobo/color wheel
128 ó147
Disable blackout while moving all options
148 ó167
Reset pan
168 ó187
Reset tilt
188
ó
207
Reset color wheel
208 ó227
Reset gobo wheel
228 ó247
Reset all channels
248 ó255
No function
11 Movement Macros
000 ó007
No function
008 ó023
Automatic movement 1
024 ó039
Automatic movement 2
040 ó055
Automatic movement 3
056 ó071
Automatic movement 4
072 ó087
Automatic movement 5
088 ó103
Automatic movement 6
104 ó119
Automatic movement 7
120 ó135
Automatic movement 8
136 ó151
Sound-active movement 1
152 ó167
Sound-active movement 2
168
ó
183
Sound-active movement 3
184 ó199
Sound-active movement 4
200 ó215
Sound-active movement 5
216 ó231
Sound-active movement 6
232 ó247
Sound-active movement 7
248 ó255
Sound-active movement 8

Intimidator™ Spot LED 150 User Manual Rev. 8 Page 13 of 18
6-CH
Channel Function Value Setting
1
Pan
000 ó255
0–540°
2
Tilt
000 ó255
0–270°
3 Color
000 ó005
White
006 ó011
Yellow
012 ó017
Magenta
018 ó023
Green
024 ó029
Red
030 ó035
Cyan
036 ó041
Orange
042 ó047
Blue
048 ó053
Light Green
054 ó063
Amber
064 ó069
White + Yellow
070 ó075
Yellow + Magenta
076 ó081
Magenta + Green
082 ó087
Green + Red
088
ó
093
Red + Cyan
094 ó099
Cyan + Orange
100 ó105
Orange + Blue
106 ó111
Blue + Light Green
112 ó117
Light Green + Amber
118 ó127
Amber + White
128 ó191
Color cycling rainbow with increasing speed
192 ó255
Reverse color cycling rainbow with increasing
speed
4 Shutter
000
ó
003
Blackout
004 ó007
Open
008 ó215
Strobe (0–20 Hz)
216 ó255
Open
5
Dimmer
000 ó255
0–100%
6 Gobo Wheel
064 ó071
Gobo 9 shake, from slow to fast
072 ó079
Gobo 8 shake, from slow to fast
080 ó085
Gobo 7 shake, from slow to fast
086 ó091
Gobo 6 shake, from slow to fast
092 ó097
Gobo 5 shake, from slow to fast
098 ó103
Gobo 4 shake, from slow to fast
104
ó
109
Gobo 3 shake, from slow to fast
110 ó115
Gobo 2 shake, from slow to fast
116 ó121
Gobo 1 shake, from slow to fast
122 ó127
Open
128 ó191
Cycle effect with increasing speed
192
ó
255
Reverse cycle effect with increasing speed

Page 14 of 18 Intimidator™ Spot LED 150 User Manual Rev. 8
Configuration
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
Never connect a product that is operating in any standalone mode (either Static,
Automatic, or Sound) to a DMX string connected to a DMX controller. Products in
standalone mode may transmit DMX signals that could interfere with the DMX
signals from the controller.
Sound-
Active
Mode
To enable the Sound-Active mode, do the following:
1. Press <MODE/ESC> repeatedly until one of the following shows on the display:
NASL, NAFA, NStS,or SLAv.
2. Press <UP> or <DOWN> to select NStS.
3. Press <ENTER>.
The product will only respond to low frequencies of music (bass and drums).
Automatic Mode
To enable the Automatic mode, follow the instructions below:
1. Press <MODE/ESC> repeatedly until one of the following shows on the display:
NASL, NAFA, NStS,or SLAv.
2. Press <UP> or <DOWN> to select NASL(for a slow light show) or NAFA (for a fast
light show).
3. Press <ENTER>.
Manual Pan/Tilt
Operation
To select whether you want the Intimidator™ Spot LED 150 to operate with normal
panning or inverted panning, do the following:
1. Press <MODE/ESC> repeatedly until PAn shows on the display.
2. Press <UP> or <DOWN> to select normal pan operation (PAn) or inverse pan
operation (r PAn).
3. Press <ENTER>.
To select whether you want the Intimidator™
Spot LED 150 to operate with normal tilting
or inverted tilting, do the following:
1. Press <MODE/ESC> repeatedly until tiL shows on the display.
2. Press <UP> or <DOWN> to select normal pan operation (tiL) or inverse pan
operation (r tiL).
3. Press <ENTER>.
Pan/Tilt Angle
Range
You are able to restrict the pan and tilt angles on the Intimidator™
Spot LED 150 to
achieve the effect you like.
To select which pan angle range to use, do the following:
1. Press <MODE/ESC> repeatedly until PA54 shows on the display.
2. Press <UP> or <DOWN> to select 540° (PA54), 360° (PA36) or 180° (PA18).
3. Press <ENTER>.
To select which tilt range to use, do the following:
1. Press <MODE/ESC> repeatedly until Ti27 shows on the display.
2. Press <UP> or <DOWN> to select either 270° (Ti27), 180° (Ti18) or 90° (Ti 9).
3. Press <ENTER>.

Intimidator™ Spot LED 150 User Manual Rev. 8 Page 15 of 18
Display
Orientation
You are able to flip the LED display for easy readability in any mounting situation.
To select your display angle:
1. Press <MODE/ESC> repeatedly until diS shows on the display.
2. Press <UP> or <DOWN> to select normal display mode (diS) or inverse display
mode (r diS).
3. Press <ENTER>.
Master/Slave
Mode
The Master/Slave mode allows a single Intimidator™ Spot LED 150 unit (the “master”) to
control the actions of one or more Intimidator™ Spot LED 150
units (the “slaves”)
without the need of a DMX controller. The master unit will be set to operate in either
Automatic or Sound-Active mode, while the slave units will be set to operate in Slave
mode. Once set and connected, the slave units will operate in
unison with the master
unit.
Configure the units as indicated below.
Slave units:
1. Press <MODE/ESC> repeatedly until SLAvshows on the display.
2. Press <ENTER> to accept.
3. Set the DMX address to 001.
4. Connect the DMX input of the first slave unit to the DMX output of the master unit.
5. Connect the DMX input of the subsequent slave units to the DMX output of the
previous slave unit.
6. Finish setting and connecting all the slave units.
Master unit:
1. Set the master unit to operate in either Automatic or Sound mode.
2. Make the master unit the first unit in the DMX daisy chain.
•Configure
all the slave units before connecting the master unit to the DMX
daisy chain.
•
Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller
may interfere with the signals from the
master unit.
•Do not connect more than 31 slave units to the master unit.
Reset Software
To reset the software on the Intimidator™ Spot LED 150, do the following:
1. Press <MODE/ESC> repeatedly until rESt shows on the display.
2. Press <ENTER>. The product will reset all settings in the software to the default
factory settings.

Page 16 of 18 Intimidator™ Spot LED 150 User Manual Rev. 8
5.TECHNICAL INFORMATION
Product
Maintenance
Dust build up reduces light output performance and
can cause overheating. This can
lead to reduction of the light source’s life and/or mechanical wear. To maintain optimum
performance and minimize wear, you should clean your lighting products at least twice a
month. However, be aware that usage and environmental conditions could be
contributing factors to increase the cleaning frequency.
To clean the product, follow the instructions below:
•Unplug the product from power.
•Wait until the product is at room temperature.
•Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external surface/vents.
•Clean all external optics with a mild soap solution, ammonia-free glass cleaner, or
isopropyl alcohol.
•Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue.
•Softly drag any dirt or grime to the outside edges of the external optics.
•Gently polish the external optics until they are free of haze and lint.
Always dry the external optics carefully after cleaning them.
Do not spin the cooling fan/fans using compressed air because you could damage
it/them.

Intimidator™ Spot LED 150 User Manual Rev. 8 Page 17 of 18
6.TECHNICAL SPECIFICATIONS
Dimensions and
Weight
Length
Width
Height
Weight
8.1 in (205 mm)
8.3 in (211 mm)
11.5 in (291 mm)
9.3 lbs (4.2 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100~240 V, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
88 W
92 W
Operating
0.7 A
0.4 A
Power linking current (units)
8 A (6 units)
8 A (12 units)
Fuse
F 2 A, 250 V
F 2 A, 250 V
Power I/O
US/Worldwide
UK/Europe
Power input connector
IEC
IEC
Power output connector
Edison
IEC
Power Cord plug
Edison (US)
Local plug
Light Source
Type
Power
Lifespan
LED
25 W
50,000 hours
Color
Quantity
Current
White
1
1.5 A
Photo Optic
Parameter
Illuminance @ 2 m
4300 lux
Beam angle
15º
Strobe rate
0–20 Hz
Pan & Tilt
540°
270°
Pan/Tilt Ranges
540°, 360°, 180°
Pan
270°, 180°, 90°
Tilt
Thermal
Maximum External Temp.
Cooling System
104° F (40° C)
Fan
DMX
I/O Connectors
Connector Type
Channel Range
3-pin XLR
Sockets
6, 11
Ordering
Product Name
Item Code
Item Number
Intimidator™ Spot LED 150
08010176
INTSPOTLED150

Page 18 of 18 Intimidator™ Spot LED 150 User Manual Rev. 8
In case you need to return a product or request support, follow the procedure below:
•If you live in the U.S., contact CHAUVET® World Headquarters (see below).
•If you live in the UK or Ireland, contact CHAUVET® Europe Ltd. (see below).
•If you live in any other country, DO NOT contact CHAUVET®. Instead, contact your
distributor of record. See www.chauvetlighting.com for distributors outside the U.S.,
United Kingdom, or Ireland.
If you live outside the U.S., United Kingdom, or Ireland, contact your distributor of
record and follow their instructions on how to return CHAUVET® product
s to
them. Visit our website for contact details.
Returns
Call the corresponding CHAUVET®
Tech Support office and request a Return
Merchandise Authorization (RMA) number before shipping the product
. Be prepared to
provide the model number, serial number, and a brief description of the cause for the
return.
You must send the merchandise prepaid
, in its original box, and with its original packing
and accessories. CHAUVET® will not issue call tags.
Clearly label the package with the RMA number. CHAUVET® will refuse any product
returned without an RMA number.
Write the RMA number on a properly affixed label. DO NOT write the RMA number
directly on the box.
Before sending the product, clearly write
the following information on a piece of paper
and place it inside the box:
•Your name
•Your address
•Your phone number
•RMA number
•A brief description of the problem
Be sure to pack the product
properly. Any shipping damage resulting from inadequate
packaging will be your responsibility. As a suggestion, proper UPS packing or double-
boxing is always a safe method to use.
CHAUVET®
reserves the right to use its own discretion to repair or replace
returned product(s).
Contact Us
World Headquarters
CHAUVET®
General Information
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Toll free: [phone]
United Kingdom & Ireland
CHAUVET® Europe Ltd.
General Information
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Technical Support
Voice: [phone] (Press 4)
Fax: [phone]
Email: [e-mail]
Technical Support
Email: [e-mail]
World Wide Web
www.chauvetlighting.com
World Wide Web
www.chauvetlighting.co.uk