Checkpoint Smart-1 225 User manual

14 January 2016
Getting Started Guide
Smart-1 225/3050/3150
Appliances
Models: ST-25, ST-50, ST-150
Classification: [Protected] P/N: 706625

© 2016 Check Point Software Technologies Ltd.
All rights reserved. This product and related documentation are protected by copyright
and distributed under licensing restricting their use, copying, distribution, and
decompilation. No part of this product or related documentation may be reproduced in
any form or by any means without prior written authorization of Check Point. While
every precaution has been taken in the preparation of this book, Check Point assumes
no responsibility for errors or omissions. This publication and features described
herein are subject to change without notice.
RESTRICTED RIGHTS LEGEND:
Use, duplication, or disclosure by the government is subject to restrictions as set forth
in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software
clause at DFARS 252.227-7013 and FAR 52.227-19.
TRADEMARKS:
Refer to the Copyright page http://www.checkpoint.com/copyright.html for a list of our
trademarks.
Refer to the Third Party copyright notices
http://www.checkpoint.com/3rd_party_copyright.html for a list of relevant copyrights
and third-party licenses.

Important Information
Latest Software
We recommend that you install the most recent software release to stay up-to-date
with the latest functional improvements, stability fixes, security enhancements and
protection against new and evolving attacks.
Latest Documentation
The latest version of this document is at:
http://supportcontent.checkpoint.com/documentation_download?ID=32309
To learn more, visit the Check Point Support Center
http://supportcenter.checkpoint.com.
For more about this release, see the
Smart-1 Appliances home page
http://supportcontent.checkpoint.com/solutions?id=sk98931.
Revision History
Date
Description
14 January 2016 Included Spanish translation of this guide
18 December 2014 Added Russian Operational Instructions ("Установка и
Конфигурирование (RU)" on page 63)
28 July 2014 Replaced telescopic rails installation procedures with a link
to the
Telescopic Rails installation booklet ("Installing
Telescoping Rails" on page 21)
15 May 2014 First release of this document
Feedback
Check Point is engaged in a continuous effort to improve its documentation.
Please help us by sending your comments
[email protected]?subject=Feedback on Smart-1 225/3050/3150
Appliances Getting Started Guide.

Safety, Environmental, and Electronic Emissions Notices
4| Smart-1 225/3050/3150 Appliances Getting Started Guide
Safety, Environmental, and
Electronic Emissions Notices
Read the following warnings before setting up or using the appliance.
Warning - Do not block air vents. A minimum 1/2-inch (13mm) clearance is
required.
Important - We recommend that only experienced personnel install or remove
hardware components. Installing or removing components incorrectly can
permanently damage the appliance.
Before you install or remove a chassis, or work near power supplies, turn off the
power and unplug the power cord.
To prevent damage to any system board, it is important to handle it with care. The
following measures are generally sufficient to protect your equipment from static
electricity discharge:
•When handling the board, to use a grounded wrist strap designed for static
discharge elimination.
•Touch a grounded metal object before removing the board from the antistatic bag.
•Handle the board by its edges only. Do not touch its components, peripheral chips,
memory modules or gold contacts.
•When handling processor chips or memory modules, avoid touching their pins or
gold edge fingers.
•Restore the communications appliance system board and peripherals back into the
antistatic bag when they are not in use or not installed in the chassis. Some
circuitry on the system board can continue operating even though the power is
switched off.
•Under no circumstances should the lithium battery cell used to power the
real-time clock be allowed to short. The battery cell may heat up under these
conditions and present a burn hazard.

Safety, Environmental, and Electronic Emissions Notices
Smart-1 225/3050/3150 Appliances Getting Started Guide | 5
Warning - DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTERIES
ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS.
•Disconnect the system board power supply from its power source before you
connect or disconnect cables or install or remove any system board components.
Failure to do this can result in personnel injury or equipment damage.
•Avoid short-circuiting the lithium battery; this can cause it to superheat and cause
burns if touched.
•Do not operate the processor without a thermal solution. Damage to the processor
can occur in seconds.
•Class 1 laser product warning - A totally enclosed laser system containing a class
1 laser.
Rack Mount Instructions
The following or similar rack-mount instructions are included with the installation
instructions:
1.
Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly,
the operating ambient temperature of the rack environment may be greater than
room ambient. Therefore, consideration should be given to installing the
equipment in an environment compatible with the maximum ambient temperature
specified by the manufacturer.
2.
Reduced Air Flow - Installation of the equipment in a rack should be such that the
amount of air flow required for safe operation of the equipment is not
compromised.
3.
Mechanical Loading - Mounting of the equipment in the rack should be such that a
hazardous condition is not achieved due to uneven mechanical loading.
4.
Circuit Overloading - Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits might
have on over current protection and supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
5.
Reliable Earthing - Reliable earthing of rack-mounted equipment should be
maintained. Particular attention should be given to supply connections other than
direct connections to the branch circuit (e.g. use of power strips).

Safety, Environmental, and Electronic Emissions Notices
6| Smart-1 225/3050/3150 Appliances Getting Started Guide
For California:
Perchlorate Material - special handling may apply. See
http://www.dtsc.ca.gov/hazardouswaste/perchlorate
The foregoing notice is provided in accordance with California Code of Regulations
Title 22, Division 4.5, Chapter 33. Best Management Practices for Perchlorate
Materials. This product, part, or both may include a lithium manganese dioxide battery
which contains a perchlorate substance.
Proposition 65 Chemical
Chemicals identified by the State of California, pursuant to the requirements of the
California Safe Drinking Water and Toxic Enforcement Act of 1986, California Health &
Safety Code s. 25249.5, et seq. ("Proposition 65"), that is "known to the State to cause
cancer or reproductive toxicity" (see http://www.calepa.ca.gov)
WARNING:
Handling the cord on this product will expose you to lead, a chemical known to the
State of California to cause cancer, and birth defects or other reproductive harm.
Wash hands after handling.
Federal Communications Commission (FCC) Statement:
For a Class A digital device or peripheral
Note: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
For a Class B digital device or peripheral
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful

Safety, Environmental, and Electronic Emissions Notices
Smart-1 225/3050/3150 Appliances Getting Started Guide | 7
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Information to user:
The user's manual or instruction manual for an intentional or unintentional radiator
shall caution the user that changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate the
equipment. In cases where the manual is provided only in a form other than paper,
such as on a computer disk or over the Internet, the information required by this
section may be included in the manual in that alternative form, provided the user can
reasonably be expected to have the capability to access information in that form.
Canadian Department Compliance Statement:
This Class A digital apparatus complies with Canadian ICES-003. Cet appareil
numérique de la classe A est conforme à la norme NMB-003 du Canada.
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil
numérique de la classe B est conforme à la norme NMB-003 du Canada.
Japan Compliance Statement:
Class A

Safety, Environmental, and Electronic Emissions Notices
8| Smart-1 225/3050/3150 Appliances Getting Started Guide
Class B
European Union (EU) Electromagnetic Compatibility Directive
This product is herewith confirmed to comply with the requirements set out in the
Council Directive on the Approximation of the Laws of the Member States relating to
Electromagnetic Compatibility Directive (2004/108/EC). For the evaluation regarding
the Electromagnetic Compatibility (2004/108/EC)
This product is in conformity with Low Voltage Directive 2006/95/EC, and complies with
the requirements in the Council Directive 2006/95/EC relating to electrical equipment
designed for use within certain voltage limits and the Amendment Directive
93/68/EEC.
Product Disposal
This symbol on the product or on its packaging indicates that this product must not be
disposed of with your other household waste. Instead, it is your responsibility to
dispose of your waste equipment by handing it over to a designated collection point for
the recycling of waste electrical and electronic equipment. The separate collection and
recycling of your waste equipment at the time of disposal will help to conserve natural
resources and ensure that it is recycled in a manner that protects human health and
the environment. For more information about where you can drop off your waste
equipment for recycling, please contact your local city office or your household waste
disposal service.

Safety, Environmental, and Electronic Emissions Notices
Smart-1 225/3050/3150 Appliances Getting Started Guide | 9
Remarques Relatives à la Sécurité,
l'environnement et les Émissions Électroniques
Avant de mettre en place ou d'utiliser l'appareil, veuillez lire les avertissements
suivants.
Avertissement: Ne pas obturer les aérations. Il faut laisser au moins 1,27 cm
d'espace libre.
Avertissement: Nous recommandons que seuls les personnes autorisées et
compétentes, puissent installer et désinstaller les parties matériels/hardware.
L’installation ou la désinstallation de components matériels peuvent
endommager l’appareil.
Avant de manipuler une appliance ou ses blocs d’alimentations, l’éteindre et
débrancher son câble électrique.
Pour éviter d'endommager les cartes système, il est important de les manipuler avec
soin. Les mesures suivantes sont généralement suffisantes pour protéger votre
équipement contre les décharges d'électricité statique:
•Avant de manipuler la carte, portez aux poignet un bracelet antistatique relié à la
terre.
•Touchez un objet métallique relié à la terre avant d'extraire la carte de son sachet
antistatique.
•Ne tenez la carte que par ses bords. Ne touchez aucun composant, puce
périphérique, module mémoire ou contact plaqué or.
•Lorsque vous manipulez des processeurs ou des modules mémoire, évitez de
toucher leurs broches ou les pistes de contact dorées.
•Remettez dans leur sachet antistatique la carte système et les périphériques de
l'appareil de communications lorsqu'ils ne sont pas utilisés ou installés dans le
châssis. Certains circuits sur la carte système peuvent rester fonctionnels même
si l'appareil est éteint.
•Il ne faut jamais court-circuiter la pile au lithium qui alimente l'horloge
temps-réel. Elle risque de s'échauffer et de causer des brûlures.

Safety, Environmental, and Electronic Emissions Notices
10 | Smart-1 225/3050/3150 Appliances Getting Started Guide
Avertissement: DANGER D'EXPLOSION SI LA PILE EST MAL REPLACÉE. NE
REMPLACER QU'AVEC UN TYPE IDENTIQUE OU ÉQUIVALENT,
RECOMMANDÉ PAR LE CONSTRUCTEUR. LES PILES DOIVENT ÊTRE MISES
AU REBUT CONFORMÉMENT AUX INSTRUCTIONS DE LEUR FABRICANT.
•Débrancher l'alimentation de la carte système de sa source électrique avant de
connecter ou déconnecter des câbles ou d'installer ou retirer des composants. À
défaut, les risques sont d'endommager l'équipement et de causer des blessures
corporelles.
•Ne pas court-circuiter la pile au lithium: elle risque de surchauffer et de causer
des brûlures en cas de contact.
•Ne pas faire fonctionner le processeur sans refroidissement. Le processeur peut
être endommagé en quelques secondes.
•Produit laser de classe 1: un système laser totalement clos et contenant un laser
de classe 1.
Instructions de montage en rack
Les instructions d'installation sont livrées avec les instructions de montage en rack
ci-après (ou similaires):
1.
Fonctionnement à température plus élevée: Si l'appareil est installé dans une
armoire fermée ou un rack à plusieurs unités, la température du rack en
fonctionnement peut être supérieure à la température ambiante de la pièce. Avant
d'installer l'équipement, il faut donc s'assurer qu'il sera dans un environnement
compatible avec la température ambiante maximale indiquée par le constructeur.
2.
Circulation d'air réduite: L'installation dans un rack doit s'assurer de ne pas
limiter la circulation de l'air nécessaire au bon fonctionnement de l'équipement.
3.
Charge mécanique: Lors du montage de l'équipement dans le rack, il faut faire
attention à ne pas déséquilibrer l'ensemble. Un rack se remplit en commençant
par le bas.
4.
Surcharge: Pour la connexion de l'équipement au circuit électrique, il faut vérifier
les risques de surcharge et les éventuelles conséquences sur la protection contre
les surtensions et sur le câblage électrique. Dans ce contexte, il faut tenir compte
des informations mentionnées par l’étiquette apposée sur l’équipement.
5.
Mise à la terre: Les équipements montés en rack doivent être en permanence
reliés à un terre fiable. Il faut faire particulièrement attention aux branchements
qui ne vont pas directement à la source électrique (par exemple des multiprises).