Chicago Electric 65817 Installation manual

19.2V 1/2” CORDLESS IMPACT
WRENCH
Model 65817
SET UP AND OPERATING INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright©2007 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Distributed exclusively by Harbor Freight Tools®

Page 2SKU 65817 For technical questions, please call 1-800-444-3353.
CONTENTS
IMPORTANT SAFETY INFORMATION ............................ 3
GENERAL SAFETY RULES ................................................. 4
Work Area ...................................................................................4
Electrical Safety .........................................................................4
Personal Safety..........................................................................4
Tool Use and Care......................................................................5
Service ........................................................................................5
SPECIFIC SAFETY RULES .................................................. 5
GROUNDING ....................................................................7
Grounded Tools: Tools with Three Prong Plugs ....................7
Double Insulated Tools: Tools with Two Prong Plugs............8
Extension Cords ........................................................................8
Symbology..................................................................................9
SPECIFICATIONS............................................................10
UNPACKING ....................................................................10
SET UP INSTRUCTIONS................................................. 10
Tool Features.............................................................................10
Charging ....................................................................................11
OPERATING INSTRUCTIONS.........................................12
MAINTENANCE, AND SERVICE..................................... 13
Replacing the Carbon Brushes ...............................................13
Troubleshooting........................................................................14
PARTS LIST..................................................................... 15
ASSEMBLY DIAGRAM....................................................16
WARRANTY.....................................................................17

Page 3SKU 65817 For technical questions, please call 1-800-444-3353.
SAVE THIS MANUAL
Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the product’s serial number
in the back of the manual near the assembly diagram (or month and year of purchase if
product has no number). Keep this manual and the receipt in a safe and dry place for
future reference.
IMPORTANT SAFETY INFORMATION
In this manual, on the labeling, and all other information
provided with this product:
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.
DANGER indicates a hazardous situation
which, if not avoided, will result in death or
serious injury.
WARNING indicates a hazardous situation
which, if not avoided, could result in death
or serious injury.
CAUTION, used with the safety alert
symbol, indicates a hazardous situation
which, if not avoided, could result in minor
or moderate injury.
NOTICE is used to address practices not
related to personal injury.
CAUTION, without the safety alert symbol,
is used to address practices not related to
personal injury.
DANGER
WARNING
CAUTION
NOTICE
CAUTION

Page 4SKU 65817 For technical questions, please call 1-800-444-3353.
GENERAL SAFETY RULES
WARNING! Read all instructions
Failure to follow all instructions listed below may result in electric shock,
re, and/or serious injury. The term “power tool” in all of the warnings listed
below refers to your mains-operated (corded) power tool or battery-operated
(cordless) power tool.
SAVE THESE INSTRUCTIONS
Work area safety1.
Keep work area clean and well lit.a. Cluttered or dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the pres-b.
ence of ammable liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
Keep children and bystanders away while operating a power tool.c. Dis-
tractions can cause you to lose control.
Electrical safety2.
Power tool plugs must match the outlet. Never modify the plug in any way.a.
Do not use any adapter plugs with earthed (grounded) power tools. Unmodi-
ed plugs and matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces such as pipes, radia-b.
tors, ranges and refrigerators. There is an increased risk of electric shock if
your body is earthed or grounded.
Do not expose power tools to rain or wet conditions.c. Water entering a
power tool will increase the risk of electric shock.
Do not abuse the cord. Never use the cord for carrying, pulling or un-d.
plugging the power tool. Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the risk of electric
shock.
Personal safety3.
Stay alert, watch what you are doing and use common sense when operatinga.
a power tool. Do not use a power tool while you are tired or under the inu-
ence of drugs, alcohol or medication. A moment of inattention while operating
power tools may result in serious personal injury.
Use safety equipment. Always wear eye protection.b. Safety equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing protec-
tion used for appropriate conditions will reduce personal injuries.
Remove any adjusting key or wrench before turning the power tool on.c. A
wrench or a key left attached to a rotating part of the power tool may result in
personal injury.

Page 5SKU 65817 For technical questions, please call 1-800-444-3353.
Do not overreach. Keep proper footing and balance at all times.d. This en-
ables better control of the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewelry. Keep your hair, cloth-e.
ing and gloves away from moving parts. Loose clothes, jewelry or long hair
can be caught in moving parts.
Power tool use and care4.
Do not force the power tool. Use the correct power tool for your application.a.
The correct power tool will do the job better and safer at the rate for which it
was designed.
Do not use the power tool if the Trigger does not turn it on and off.b. Any power
tool that cannot be controlled with the Trigger is dangerous and must be re-
paired.
Disconnect the battery pack from the power tool before making anyc.
adjustments, changing accessories, or storing power tools. Such pre-
ventive safety measures reduce the risk of starting the power tool acci-
dentally.
Store idle power tools out of the reach of children and do not allow per-d.
sons unfamiliar with the power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment or binding of moving parts,e.
breakage of parts and any other condition that may affect the power tools
operation. If damaged, have the power tool repaired before use. Many ac-
cidents are caused by poorly maintained power tools.
Keep tools clean.f. Properly maintained tools are less likely to bind and are
easier to control.
Use the power tool, accessories and sockets etc., in accordance with theseg.
instructions and in the manner intended for the particular type of power tool,
taking into account the working conditions and the work to be performed. Use
of the power tool for operations different from those intended could result in a
hazardous situation.
Service5.
Have your power tool serviced by a qualied repair person using only identi-a.
cal replacement parts. This will ensure that the safety of the power tool is
maintained.
SPECIFIC SAFETY RULES
Maintain labels and nameplates on the tool. These carry important safety infor-1.
mation. If unreadable or missing, contact Harbor Freight Tools for a replacement.
Avoid unintentional starting. Prepare to begin work before turning on the tool.2.

Page 6SKU 65817 For technical questions, please call 1-800-444-3353.
Do not lay the tool down until it has come to a complete stop. Moving parts can3.
grab the surface and pull the tool out of your control.
When using a handheld power tool, maintain a rm grip on the tool with both 4.
hands to resist starting torque.
Do not leave the tool unattended when it is plugged into an electrical outlet. Turn5.
off the tool, and unplug it from its electrical outlet before leaving.
Use clamps (not included) or other practical ways to secure and support the6.
workpiece to a stable platform. Holding the work by hand or against your body is
unstable and may lead to loss of control.
7. The battery charger gets hot during use. The charger’s heat can build
up to unsafe levels and create a re hazard if it does not receive
adequate ventilation, due to an electrical fault, or if it is used in a hot
environment.
Do not place the charger on a ammable surface. Do not obstruct any vents on
the charger. Especially avoid placing the charger on carpets and rugs; they
are not only ammable, but they also obstruct vents under the charger.
Place the charger on a stable, solid, nonammable surface (such as a stable
metal workbench or concrete oor) at least 1 foot away from all ammable ob-
jects, such as drapes or walls. Keep a re extinguisher and a smoke detector in
the area. Frequently monitor the charger and battery during use.
This product is not a toy. Keep it out of reach of children.8.
People with pacemakers should consult their physician(s) before use. Electro-9.
magnetic elds in close proximity to heart pacemaker could cause pacemaker
interference or pacemaker failure. In addition, people with pacemakers should:
• Avoid operating alone.
• Do not use with power switch locked on.
• Properly maintain and inspect to avoid electrical shock.
• Any power cord must be properly grounded. Ground Fault Circuit Interrupter
(GFCI) should also be implemented – it prevents sustained electrical shock.
Some dust created by power sanding, sawing, grinding, drilling, and other con-10.
struction activities, contains chemicals known [to the State of California] to cause
cancer, birth defects or other reproductive harm. Some examples of these chem-
icals are: Lead from lead-based paints
Crystalline silica from bricks and cement or other masonry products
Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as those dust masks that
are specially designed to lter out microscopic particles. (California Health &
Safety Code § 25249.5, et seq.)

Page 7SKU 65817 For technical questions, please call 1-800-444-3353.
Only use the included battery to power the Inpact Wrench. Never attempt to use11.
a battery from any other powered tool in place of the battery for this tool.
The warnings, precautions, and instructions discussed in this instruction manual12.
cannot cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
SAVE THESE INSTRUCTIONS.
GROUNDING
Improperly connecting the grounding wire can result in
electric shock.
Check with a qualied electrician if you are in doubt as to
whether the outlet is properly grounded. Do not modify
the power cord plug provided with the tool. Never remove
the grounding prong from the plug. Do not use the tool if
the power cord or plug is damaged. If damaged, have it
repaired by a service facility before use. If the plug will not
t the outlet, have a proper outlet installed by a qualied
electrician.
Grounded Tools: Tools with Three Prong Plugs
Tools marked with “Grounding Required” have a three wire cord and three prong 1.
grounding plug. The plug must be connected to a properly grounded outlet. If
the tool should electrically malfunction or break down, grounding provides a low
resistance path to carry electricity away from the user, reducing the risk of electric
shock. (See 3-Prong Plug and Outlet.)
The grounding prong in the plug is connected through the green wire inside the2.
cord to the grounding system in the tool. The green wire in the cord must be the
only wire connected to the tool’s grounding system and must never be attached
to an electrically “live” terminal. (See 3-Prong Plug and Outlet.)
The tool must be plugged into an appropriate outlet, properly installed and3.
grounded in accordance with all codes and ordinances. The plug and outlet
should look like those in the following illustration.
(See 3-Prong Plug and Outlet.)
WARNING

Page 8SKU 65817 For technical questions, please call 1-800-444-3353.
3-Prong Plug and Outlet Outlets for 2-Prong Plug
Double Insulated Tools: Tools with Two Prong Plugs
Tools marked “Double Insulated” do not require grounding. They have a special 1.
double insulation system which satises OSHA requirements and complies with
the applicable standards of Underwriters Laboratories, Inc., the Canadian Stan-
dard Association, and the National Electrical Code.
(See Outlets for 2-Prong Plug.)
Double insulated tools may be used in either of the 120 volt outlets shown in the2.
preceding illustration. (See Outlets for 2-Prong Plug.)
Extension Cords
Grounded1. tools require a three wire extension cord. Double Insulated tools can
use either a two or three wire extension cord.
As the distance from the supply outlet increases, you must use a heavier gauge2.
extension cord. Using extension cords with inadequately sized wire causes a
serious drop in voltage, resulting in loss of power and possible tool damage.
(See Table A.)
The smaller the gauge number of the wire, the greater the capacity of the cord.3.
For example, a 14 gauge cord can carry a higher current than a 16 gauge cord.
(See Table A.)
When using more than one extension cord to make up the total length, make4.
sure each cord contains at least the minimum wire size required. (See Table A.)
If you are using one extension cord for more than one tool, add the nameplate5.
amperes and use the sum to determine the required minimum cord size.
(See Table A.)
If you are using an extension cord outdoors, make sure it is marked with the suf-6.
x “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.

Page 9SKU 65817 For technical questions, please call 1-800-444-3353.
Make sure the extension cord is properly wired and in good electrical condition.7.
Always replace a damaged extension cord or have it repaired by a qualied elec-
trician before using it.
Protect the extension cords from sharp objects, excessive heat, and damp or wet8.
areas.
RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120/240 VOLT)
NAMEPLATE
AMPERES
(at full load)
EXTENSION CORD LENGTH
25 Feet 50 Feet 75 Feet 100 Feet 150 Feet
0 – 2.0 18 18 18 18 16
2.1 – 3.4 18 18 18 16 14
3.5 – 5.0 18 18 16 14 12
5.1 – 7.0 18 16 14 12 12
7.1 – 12.0 18 14 12 10 -
12.1 – 16.0 14 12 10 - -
16.1 – 20.0 12 10 - - -
TABLE A * Based on limiting the line voltage drop to ve volts at 150% of the rated amperes.
Symbology
Double Insulated V~ Volts Alternating Current
Canadian Standards Association AAmperes
Underwriters Laboratories, Inc. n0xxxx/min. No Load Revolutions per Minute
(RPM)

Page 10SKU 65817 For technical questions, please call 1-800-444-3353.
SPECIFICATIONS
Charger Input 120 V~, 60 Hz, 1.8 A
Charger Output 7.2 - 24 V, 1.5 A
Charge Time 5 hours (Initial)
3-5 hours (Recharging)
Speed 0-2300 RPM
Maximum Torque 220 ft-lb
Battery Cell Type NiCd, 1700 mAh, 1.2 V, Item 96756
UNPACKING
When unpacking, check to make sure that the item is intact and undamaged. If
any parts are missing or broken, please call Harbor Freight Tools at the number shown
on the cover of this manual as soon as possible.
List of contents
Description Qty
Impact Wrench 1
Charger 1
Battery 1
Replacement Carbon Brush 4
SET UP INSTRUCTIONS
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the
beginning of this manual including all text under subheadings therein
before set up or use of this product.
Risk of accidental starting; resulting in serious personal
injury. Turn the Forward/Reverse Switch to the center, locked
position and unplug the battery from the Impact Wrench
before making any adjustments to the tool.
Note: For additional information regarding the parts listed in the following pages, refer
to the Assembly Diagram near the end of this manual.
Tool Features
Always make sure the Trigger (36) of the Impact Wrench is not depressed, the1.
Forward/Reverse Switch (32) is in the center, locked position, the Battery (37)
is removed from the Impact Wrench, and the Charger (39) is unplugged from an
electrical outlet prior to making any adjustments to the tool.
WARNING

Page 11SKU 65817 For technical questions, please call 1-800-444-3353.
Trigger (36): Squeeze the Trigger to turn the Impact Wrench on and release pressure
on the Trigger to turn the Impact Wrench off.
Forward/Reverse Switch (32): The Forward/Reverse Switch allows you to change
the rotational direction of the Impact Wrench. For a clockwise rotation, move
the Forward/Reverse Button to the right. For a counterclockwise rotation, move
the Forward/Reverse Button to the left. To avoid damage to the Impact Wrench,
always wait until the tool completely stops before changing rotational directions.
1/2” Drive Impact Head (7): The 1/2” Impact Head securely holds a socket.
Battery (37): The power source for the Impact Wrench is a rechargeable, 19.2 VDC
Battery. Make sure to follow all safety precautions when working with the Battery.
Charger (39): The Charger is powered by plugging the Power Plug into a 120 volt,
grounded, electrical outlet. NEVER attempt to power the Charger with any other
electrical source other than a 120 volt, grounded electrical outlet.
To 120 Volt,
Grounded,
Electrical
Outlet.
Battery
(37)
Charger
(39)
Impact Head
(7)
Trigger (36)
Forward/Reverse
Switch (32)
Battery (37)
FIGURE A
Charging
The Battery (37) must be charged for1. 5 hours, prior to the rst use of the Impact
Wrench.
After rst use, the Battery (37) should only be recharged when the performance 2.
of the Impact Wrench begins to diminish. Severe heat is destructive to batteries;
the more heat generated, the faster the battery will lose power. A battery that
gets too hot can be permanently damaged. Never discharge the battery by con-
tinuing to pull the Trigger after the tool’s performance begins to diminish. Stop
the tool, re-charge the battery, and use the fresh battery for optimal performance.
REV 09a

Page 12SKU 65817 For technical questions, please call 1-800-444-3353.
When the Battery requires recharging, a 3. 3-5 hour charge allows the tool to oper-
ate at full power.
Slide the Battery off the handle of the Impact Wrench. Insert the Battery into4.
the socket of the Charger (39). Then plug the Charger into the nearest 120 volt,
grounded, electrical outlet.
Verify that the RED Charging Indicator Light comes on. If it does not illuminate,5.
check the power connection or try a different electrical outlet. Charge the Bat-
tery for 1-3/4 hours. NOTE: When the Battery is fully charged the RED Charging
Indicator Light will turn off, and the GREEN Charged Light will illuminate.
While charging, the Battery and Charger may become warm to the touch. This is6.
normal and does not indicate a problem.
Once the Battery is fully charged, disconnect the Charger from the electrical out-7.
let. Remove the Battery from the Charger, and insert the Battery into the handle
of the Impact Wrench.
NOTE: Allow the battery to cool down before recharging it.
NOTE: To prevent accidents, turn off the tool and disconnect its power supply
after use. Clean, then store the tool indoors out of children’s reach.
OPERATING INSTRUCTIONS
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the
beginning of this manual including all text under subheadings therein
before set up or use of this product.
General operating instructions
Before installing a socket, make sure the Battery (37) is removed from the Impact1.
Wrench to avoid accidental starting. Then, rmly insert the Socket onto the 1/2”
Impact Head (7) of the tool. (See Figure A.)
Always x the workpiece securely in place, using a vise or clamps (not included).2.
Insert the fully charged Battery into the handle of the Impact Wrench.3.
Use the Forward/Reverse Switch (32) to select the turning rotation of the Impact4.
Wrench.
Insert the socket onto the nut that is to be loosened/tightened.5.
Hold the Impact Wrench rmly with both hands, as torque from the Motor will 6.
cause the tool to twist. Then, squeeze the Trigger (36) to turn on the Impact
Wrench.

Page 13SKU 65817 For technical questions, please call 1-800-444-3353.
When nished, release the Trigger to stop the Impact Wrench. Then, remove the 7.
Battery and socket from the tool.
Make sure to store the Impact Wrench in a dry, clean location out of reach of chil-8.
dren and other unauthorized people.
MAINTENANCE AND SERVICING
Risk of serious personal injury from accidental starting or
electric shock. Turn the Forward/Reverse Switch to the
center, locked position and disconnect the Battery before
performing any inspection, maintenance, or cleaning
procedures.
Damaged equipment can fail, causing serious personal
injury. Do not use damaged equipment. If abnormal noise or
vibration occurs, have the problem corrected before further
use.
Cleaning and Maintenance
BEFORE EACH USE,1. inspect the general condition of the tool. Check for loose
screws, misalignment or binding of moving parts, cracked or broken parts, dam-
aged electrical wiring, and any other condition that may affect its safe operation.
AFTER USE,2. clean external surfaces of the tool with clean, moist cloth.
WARNING! If the supply cord of this power tool is damaged, it must be3.
replaced only by a qualied service technician.
Dispose of the rechargeable NiCd battery according to State, Local and Federal4.
regulations. Contact a local recycling center for disposal directions.
Replacing the Carbon Brushes
It may become necessary at sometime to replace or clean the two Carbon Brush-1.
es (29) when the Motor performance decreases, or stops working completely.
Remove the two Brush Holder Caps (28), then the two Carbon Brushes (29),2.
keeping track of the orientation and location of each.
If either Carbon Brush is worn more than halfway, replace both Carbon Brushes.3.
If the Carbon Brushes are just dirty, however, they may be cleaned by rubbing
them with a pencil eraser. If cleaning used brushes, try to install them in the
same holders and orientation as when they were removed.
WARNING

Page 14SKU 65817 For technical questions, please call 1-800-444-3353.
When installing the Carbon Brushes, make sure the carbon portion of the Carbon4.
Brushes contact the Motor’s Rotor and that the springs face away from the Motor.
Also, make sure the springs operate freely.
After replacement or cleaning, replace the two Brush Holder Caps.5.
NOTE: New Carbon Brushes tend to arc or spark until they wear and conform to the
Motor’s Rotor.
Troubleshooting
Problem Possible Causes Possible Solutions
Trigger Switch locked in
place.
Forward/Reverse Switch is in1.
center position.
Move button to the left or right for1.
forward or reverse operation.
Impact Wrench operates
slowly or without force.
Battery weak.1. Recharge Battery completely.1.
Impact Wrench does not
turn on.
Battery completely discharged.1. Recharge Battery completely.1.
Battery will not hold
charge.
Battery dead.1. Replace with new Battery.1.

Page 15SKU 65817 For technical questions, please call 1-800-444-3353.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
PARTS LIST
Part Description
1 Screw (1)
2 Washer (1)
3 Front Cover
4 Bearing
5 Rubber Washer
6 Plate Washer
7 Impact Head
8 Impact Shaft
9 Bearing (1)
10 Torque Spring
11 Buffer Pad
12 Spring Pad
13 Master Impact Driver
14 Steel Ball
15 Planetary Gear
16 Straight Pin
17 Bearing Pad
18 Bearing (2)
19 Inner Rim
20 Rim Shaft
Part Description
21 Bearing (3)
22 Armature
23 Plate
24 Washer (2)
25 Stator
26 Bearing (2)
27 Carbon Brush Shaft
28 Brush Holder Cap
29 Carbon Brush
30 Brush Holder
31 Connector
32 Forward/Reverse Switch
33 Right Body
34 Left Body
35 Carrying Strap
36 Trigger
37 Battery
38 Screw (2)
39 Charger (not shown)

Page 16SKU 65817 For technical questions, please call 1-800-444-3353.
ASSEMBLY DIAGRAM
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
38

Page 17SKU 65817 For technical questions, please call 1-800-444-3353.
LIMITED 90 DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this prod-
uct is free from defects in materials and workmanship for the period of 90 days from
the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities,
criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental,
contingent, special or consequential damages arising from the use of our product. Some
states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESS-
LY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us
with transportation charges prepaid. Proof of purchase date and an explanation of the
complaint must accompany the merchandise. If our inspection veries the defect, we
will either repair or replace the product at our election or we may elect to refund the
purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that
the defect resulted from causes not within the scope of our warranty, then you must
bear the cost of returning the product.
This warranty gives you specic legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • [phone]