Chicago Electric 68221 Assembly instructions

Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
ELECTRIC
CHAIN SAW
SHARPENER
REV 14i
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright©2010 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.

Page 2 For technical questions, please call 1-888-866-5797. Item 68221
SAFETY OPERATION MAINTENANCESETUP
Table of Contents
Safety ......................................................... 2
Specifications ............................................. 5
Setup .......................................................... 6
Operation.................................................... 8
Maintenance.............................................. 10
Parts List and Diagram.............................. 14
Warranty .................................................... 16
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that
follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
IMPORTANT SAFETY INFORMATION
General Tool Safety Warnings
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
1. KEEP GUARDS IN PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are
removed from tool before turning it on.
3. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite accidents.
4. DON’T USE IN DANGEROUS ENVIRONMENT.
Don’t use power tools in damp or wet locations,
or expose them to rain. Keep work area well lighted.
5. KEEP CHILDREN AWAY. All visitors should
be kept safe distance from work area.
6. MAKE WORKSHOP KID PROOF with padlocks,
master switches, or by removing starter keys.
7. DON’T FORCE TOOL. It will do the job better
and safer at the rate for which it was designed.
8. USE RIGHT TOOL. Don’t force tool or attachment
to do a job for which it was not designed.

Page 3For technical questions, please call 1-888-866-5797.Item 68221
SAFETYOPERATIONMAINTENANCE SETUP
Table A: RECOMMENDED MINIMUM WIRE GAUGE
FOR EXTENSION CORDS
(120 VOLT)
NAMEPLATE
AMPERES
(at full load)
EXTENSION CORD
LENGTH
25′ 50′ 100′ 150′
0 – 6 18 16 16 14
6.1 – 10 18 16 14 12
10.1 – 12 16 16 14 12
12.1 – 16 14 12 Do not use.
9. USE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using
an extension cord, be sure to use one heavy
enough to carry the current your product will draw.
An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating.
Table A shows the correct size to use depending
on cord length and nameplate ampere rating.
If in doubt, use the next heavier gauge.
The smaller the gauge number, the heavier the cord.
10. WEAR PROPER APPAREL. Do not wear
loose clothing, gloves, neckties, rings, bracelets,
or other jewelry which may get caught in moving
parts. Nonslip footwear is recommended.
Wear protective hair covering to contain long hair.
11. ALWAYS USE SAFETY GLASSES. Also use
face or dust mask if cutting operation is dusty.
Everyday eyeglasses only have impact resistant
lenses, they are NOT safety glasses.
12. SECURE WORK. Use clamps or a vise to
hold work when practical. It’s safer than using your
hand and it frees both hands to operate tool.
13. DON’T OVERREACH.
Keep proper footing and balance at all times.
14. MAINTAIN TOOLS WITH CARE. Keep
tools sharp and clean for best and safest
performance. Follow instructions for
lubricating and changing accessories.
15. DISCONNECT TOOLS before servicing;
when changing accessories, such as
blades, bits, cutters, and the like.
16. REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure switch is in
off position before plugging in.
17. USE RECOMMENDED ACCESSORIES.
Consult the owner’s manual for recommended
accessories. The use of improper accessories
may cause risk of injury to persons.
18. NEVER STAND ON TOOL.
Serious injury could occur if the tool is tipped or
if the cutting tool is unintentionally contacted.
19. CHECK DAMAGED PARTS. Before further use
of the tool, a guard or other part that is damaged
should be carefully checked to determine that
it will operate properly and perform its intended
function – check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting, and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or replaced.
20. DIRECTION OF FEED.
Feed work into a blade or cutter against the
direction of rotation of the blade or cutter only.
21. NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN POWER OFF. Don’t leave tool
until it comes to a complete stop.

Page 4 For technical questions, please call 1-888-866-5797. Item 68221
SAFETY OPERATION MAINTENANCESETUP
Grounding Instructions
TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT
GROUNDING WIRE CONNECTION READ AND FOLLOW THESE INSTRUCTIONS:
110-120 VAC Double Insulated Tools: Tools with Two Prong Plugs
Outlets for 2-Prong Plug
1. To reduce the risk of electric shock, double
insulated equipment has a polarized plug
(one blade is wider than the other). This plug will fit
in a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to install
the proper outlet. Do not change the plug in any way.
2. Double insulated tools may be used in either of the
120 volt outlets shown in the preceding illustration.
(See Outlets for 2-Prong Plug.)
Grinder Tool Safety Warnings
For Your Own Safety Read Instruction
Manual Before Operating Grinder
1. Wear eye protection.
2. Use grinding wheel suitable for speed of grinder.
3. Replace cracked wheel immediately.
4. Always use guards and eye shields.
5. Do not overtighten wheel nut.
6. Use only flanges furnished with the grinder.
7. Adjust distance between wheel and work rest
to maintain 0.125 inch or less separation as the
diameter of the wheel decreases with use.
8. Frequently clean grinding dust from beneath grinder.
9. Wear a full face shield over ANSI-approved
safety goggles during use.
10. Do not grind with side of wheel unless wheel is
specifically designed for that type of grinding.
11. DO NOT OPERATE WITH ANY GUARD
DISABLED, DAMAGED, OR REMOVED. Moving
guards must move freely and close instantly.
12. The use of accessories or attachments not
recommended by the manufacturer may
result in a risk of injury to persons.
13. When servicing use only identical replacement parts.
14. Only use safety equipment that has been approved
by an appropriate standards agency. Unapproved
safety equipment may not provide adequate
protection. Eye protection must be ANSI-approved
and breathing protection must be NIOSH-approved
for the specific hazards in the work area.
15. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication.
A moment of inattention while operating power
tools may result in serious personal injury.
16. Industrial applications must follow OSHA guidelines.
17. Maintain labels and nameplates on the tool.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
18. Avoid unintentional starting.
Prepare to begin work before turning on the tool.
19. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.

Page 5For technical questions, please call 1-888-866-5797.Item 68221
SAFETYOPERATIONMAINTENANCE SETUP
20. WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities, contains chemicals known to the State
of California to cause cancer and birth defects or
other reproductive harm. Some examples of these
chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement or other
masonry products
• Arsenic and chromium from chemically
treated lumber
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
(California Health & Safety Code § 25249.5, et seq.)
21. WARNING: The cord of this product contains
lead and/or di (2-ethylhexyl) phthalate (DEHP),
chemicals known to the State of California
to cause cancer, and birth defects or other
reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.)
22. The warnings, precautions, and instructions
discussed in this instruction manual cannot cover all
possible conditions and situations that may occur.
It must be understood by the operator that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the operator.
Vibration Safety
This tool vibrates during use. Repeated or
long-term exposure to vibration may cause
temporary or permanent physical injury,
particularly to the hands, arms and shoulders.
To reduce the risk of vibration-related injury:
1. Anyone using vibrating tools regularly or for an
extended period should first be examined by a
doctor and then have regular medical check-ups
to ensure medical problems are not being caused
or worsened from use. Pregnant women or
people who have impaired blood circulation to
the hand, past hand injuries, nervous system
disorders, diabetes, or Raynaud’s Disease should
not use this tool. If you feel any medical or
physical symptoms related to vibration (such as
tingling, numbness, and white or blue fingers),
seek medical advice as soon as possible.
2. Do not smoke during use. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.
3. Use tools with the lowest vibration when there
is a choice between different processes.
4. Include vibration-free periods each day of work.
5. Grip workpiece as lightly as possible (while still
keeping safe control of it). Let the tool do the work.
6. To reduce vibration, maintain the tool as
explained in this manual. If any abnormal
vibration occurs, stop use immediately.
SAVE THESE INSTRUCTIONS.
Specifications
Electrical Rating 120VAC / 60Hz / 0.7A
4004713
Motor No Load Speed 4,200 RPM
Saw Chain Pitch 1/4″ and 3/8″
Arbor Size 7/8″
Vise Capacity 0.05″ to 0.072″
Max. Accessory Diameter 4-1/4″ (108mm)
Max. Wheel Thickness 1/8″
Mounting Hardware 2x1/4″ Bolts and Nuts (sold separately)

Page 6 For technical questions, please call 1-888-866-5797. Item 68221
SAFETY OPERATION MAINTENANCESETUP
Setup - Before Use:
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool off and unplug the tool from its electrical outlet
before performing any procedure in this section.
Note: For additional information regarding the parts listed in the following pages,
refer to the Assembly Diagram near the end of this manual.
Mounting
Note: The Sharpener must be mounted
on a horizontal surface.
1. Position the Sharpener on the mounting
surface so that the mounting stop butts up
against the vertical edge of the surface.
2. Using the Base as a template, mark
locations of mounting holes.
3. Drill pilot holes appropriate for the proper hardware
(sold separately), described under Specifications
on page 5, at the marked locations.
4. Align mounting holes with pilot holes, then
secure the Base with the hardware.
Mounting
Holes
Mounting
Stop
Mounting
Surface
Figure A
Attaching the Vise
1. Slide the bolt on the bottom of the Vise assembly
through the hole on the Base. Secure from
underneath with the Angle Adjustment Knob.
Vise
Assembly
Bolt
Angle
Adjustment
Knob
Figure B
2. Remove the Clamp Lock Nut
from the Vise Cable
3. Push the Vise Cable through the hole in the
Clamp Plate and secure with Clamp Lock Nut.
Clamp
Lock Nut
Vise
Cable
Clamp
Plate
Figure C

Page 7For technical questions, please call 1-888-866-5797.Item 68221
SAFETYOPERATIONMAINTENANCE SETUP
Functions
Handle
Vise
Handle
Depth
Adjustment
Knob
Depth
Adjustment
Lock Nut
Chain Stop
Adjustment
Knob
Vise
Clamp
Plate
Clamp
Lock Nut
Chain Roller
Knob Angle
Adjustment
Knob
Chain Roller
Knob
Chain
Stop
Depth
Adjustment
Stop
Depth
Adjustment
Plate
Power
Switch
Vise
Cable
Chain Stop
Lock Nut

Page 8 For technical questions, please call 1-888-866-5797. Item 68221
SAFETY OPERATION MAINTENANCESETUP
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
Tool Set Up
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool off and unplug the tool from its electrical outlet
before performing any procedure in this section.
TO PREVENT SERIOUS INJURY:
DO NOT OPERATE WITH ANY GUARD DISABLED, DAMAGED, OR REMOVED.
Installing the Grinding Wheel
1. The Grinding Wheel MUST be:
• rated to at least 5,000 RPM.
• no larger than 4-1/4″ in diameter.
• fitted with a 7/8″ round arbor hole.
• 1/8″ thick or less.
• dry and clean.
• proven undamaged by inspection and
by the ring-test explained below.
2. Remove Grinding Wheel Cover.
3. Remove the Outer Flange by turning it
counterclockwise, then remove the Grinding Wheel.
Grinding
Wheel Cover
Outer
Flange
Inner
Flange
Spindle
Arbor
Grinding
Wheel
Screws
Figure D
4. Closely inspect the wheel before mounting.
Perform a ring-test on the wheel (unless wheel is
smaller than 4″ or is an unusual shape) as follows:
a. Suspend wheel using a dowel or
finger through the arbor hole.
b.
Tap
Wheel
Here
45° 45°
45° 45°
Hang
Wheel
from
Dowel
V
E
R
T
I
C
A
L
C
E
N
T
E
R
Tap the flat side of the wheel with a light
non-metallic object, such as a screwdriver
handle, at a point 45° from the vertical center
line on each side of the wheel and 1 – 2 inches
from the edge of the wheel (see Illustration).
c. Rotate the wheel 90° and repeat the test
until the entire wheel has been checked.
d. An undamaged wheel will
give a clear tone. If cracked, there will be
a dead sound and not a clear ring.
5. Place the Grinding Wheel on the Arbor, then
thread the Outer Flange onto the Spindle.
Wrench tighten only enough so that the
wheel is securely held on the spindle.
6. Replace the Grinding Wheel Cover.
WARNING: To prevent serious injury,
do not overtighten flange. Overtightening can
damage the wheel, causing wheel failure.

Page 9For technical questions, please call 1-888-866-5797.Item 68221
SAFETYOPERATIONMAINTENANCE SETUP
Workpiece and Work Area Set Up
1. Designate a work area that is clean and well-lit.
The work area must not allow access by children
or pets to prevent distraction and injury.
2. Route the power cord along a safe route to reach
the work area without creating a tripping hazard or
exposing the power cord to possible damage. The
power cord must reach the work area with enough
extra length to allow free movement while working.
3. There must not be objects, such as utility lines,
nearby that will present a hazard while working.
4. You must use personal safety equipment
including, but not limited to, ANSI-approved
eye protection. Wear heavy-duty gloves
when handling the saw chain.
5. Before beginning work, provide for sparks
and debris that will fly off the work surface.
General Operating Instructions
1. Unplug the Sharpener.
2. Refer to the saw chain’s instructions to
determine the sharpening angle.
3. With the angled cutting edges facing right,
place the saw chain in the Vise, engaging the
chain on the spokes of the Chain Wheels.
Angle
Arrow
Miter
Gauge
Chain
Roller
Chain Wheel
(inside Vise)
Figure E
4. Squeeze the Vise Handle to test clamping
tension. Adjust the Clamp Lock Nut until the saw
chain does not move while being clamped.
5. Sharpening the right-hand cutters:
a. Loosen the Angle Adjustment Knob, align
the Angle Arrow to the correct angle to the
left of 0 on the Miter Gauge, then tighten the
Angle Adjustment Knob. See Figure E.
b. Turn the Chain Roller until the first right-hand
cutter is in position. Then, engage the Chain
Stop to keep saw chain from moving.
c. Pull down on the Handle to bring the Grinding
Wheel into the Gullet, then make adjustments:
• Turn the Chain Stop Adjustment Knob until
the Grinding Wheel just grazes the cutting
edge. Tighten the Chain Stop Lock Nut.
• Turn the Depth Adjustment Knob until the
Grinding Wheel is just above the bottom of the
Gullet. Tighten the Depth Adjustment Lock Nut.
Cutting
Edge Gullet
Figure F: Right-hand Cutter
d. Plug in the Sharpener and turn it on.
e. Allow the Sharpener to come up to full speed.
f. Squeeze the Vise Handle and pull down on
the Handle until the Grinding Wheel makes
contact with and sharpens the cutting edge.
CAUTION! Turn the Sharpener off before moving chain.
g. Turn the Chain Roller until the next
cutter is in position. Turn the Sharpener
on, then sharpen that cutter.
h. Continue until all of the cutters
have been sharpened.
i. Turn off the Sharpener, then unplug it.
6. Sharpening the left-hand cutters:
Note: Leave the chain in the Vise.
a. Loosen the Angle Adjustment Knob, align
the Angle Arrow to the correct angle to
the right of 0 on the Miter Gauge, then
tighten the Angle Adjustment Knob.
b. Turn the Chain Roller until the first left-hand cutter
is in position. Then, engage the Chain Stop.
c. Follow instructions for 5. Sharpening the right-
hand cutters: beginning at c. and ending at i.
Gullet
Cutting
Edge
Figure G: Left-hand Cutter
7. Clean and oil the chain before
reinstalling it on the chain saw.
8. To prevent accidents, turn off the tool and unplug
the tool from its electrical outlet after use. Clean,
then store the tool indoors out of children’s reach.

Page 10 For technical questions, please call 1-888-866-5797. Item 68221
SAFETY OPERATION MAINTENANCESETUP
Maintenance and Servicing
Procedures not specifically explained in this manual must
be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool off and unplug the tool from its electrical outlet
before performing any procedure in this section.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise or vibration
occurs, have the problem corrected before further use.
Cleaning, Maintenance, and Lubrication
1. BEFORE EACH USE, inspect the general
condition of the tool. Check for:
• loose hardware,
• misalignment or binding of moving parts,
• cracked or broken parts,
• damaged electrical wiring, and
• any other condition that may
affect its safe operation.
2. AFTER USE, wipe external surfaces
of the tool with clean cloth.
3. Periodically, wear ANSI-approved
safety goggles and NIOSH-approved
breathing protection and blow dust and grit out
of the motor vents using dry compressed air.
4. Replace the Grinding Wheel once it
has worn down to a diamter of 3".
5. WARNING! If the supply cord of this
power tool is damaged, it must be replaced
only by a qualified service technician.
Accessory Storage and Handling
1. Handle accessories carefully to prevent
dropping or bumping. Do not use wheels
that have been dropped or bumped.
2. Store accessories in shelves, racks, boxes, or
drawers. Keep storage area dry and above
freezing. Any grinding or cut-off wheels exposed to
humidity or freezing temperatures must not be used.

Page 11For technical questions, please call 1-888-866-5797.Item 68221
SAFETYOPERATIONMAINTENANCE SETUP
Troubleshooting
Problem Possible Causes Likely Solutions
Tool will not start. 1. Cord not connected.
2. No power at outlet.
3. Tool’s thermal reset breaker
tripped (if equipped).
4. Internal damage or wear. (Carbon
brushes or switch, for example.)
1. Check that cord is plugged in.
2. Check power at outlet. If outlet is unpowered,
turn off tool and check circuit breaker.
If breaker is tripped, make sure circuit is right
capacity for tool and circuit has no other loads.
3. Turn off tool and allow to cool.
Press reset button on tool.
4. Have technician service tool.
Tool operates
slowly.
Extension cord too long or
wire size too small.
Eliminate use of extension cord. If an extension cord
is needed, use one with the proper diameter for its
length and load. See Table A on page 3.
Performance
decreases
over time.
1. Accessory dull or damaged.
2. Carbon brushes worn or damaged.
1. Keep cutting accessories sharp.
Replace as needed.
2. Have qualified technician replace brushes.
Excessive noise
or rattling.
1. Internal damage or wear. (Carbon
brushes or bearings, for example.)
1. Have technician service tool.
Overheating. 1. Forcing machine to work too fast.
2. Accessory dull or damaged.
3. Blocked motor housing vents.
4. Motor being strained by long or
small diameter extension cord.
1. Allow machine to work at its own rate.
2. Keep cutting accessories sharp.
Replace as needed.
3. Wear ANSI-approved safety goggles and
NIOSH-approved dust mask/respirator while
blowing dust out of motor using compressed air.
4. Eliminate use of extension cord.
If an extension cord is needed, use one with
the proper diameter for its length and load.
See Table A on page 3.
Follow all safety precautions whenever diagnosing or servicing the tool.
Disconnect power supply before service.

Page 12 For technical questions, please call 1-888-866-5797. Item 68221
SAFETY OPERATION MAINTENANCESETUP
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Page 13For technical questions, please call 1-888-866-5797.Item 68221
SAFETYOPERATIONMAINTENANCE SETUP
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.

Page 14 For technical questions, please call 1-888-866-5797. Item 68221
SAFETY OPERATION MAINTENANCESETUP
Parts List and Diagram
Parts List
Part Description Qty.
1 Screw 3
2 Back Cover 1
3 Screw 2
4 Pressure Panel 1
6 Circuit Panel 1
7 Motor 1
8 Vise Handle 1
9 Handle 1
10 Lower Valve 1
11 Power Switch 1
12 Cushion 1
13 Depth Adjustment Knob 1
14 Nut 1
15 Upper Housing 1
16 Grinding Wheel 1
17 Wheel Screw 2
18 Outer Flange 1
19 Grinding Wheel Cover 1
20 Screw 3
21 Nut 1
22 Nut 2
23 Spring Washer 2
24 Mat 2
25 Screw 2
30 Power Cord 1
31 Snap Spring 2
32 Torsion Spring 1
33 Pin Roll 1
34 Base 1
Part Description Qty.
35 Vise Cable 1
36 Screw 1
37 Mat 3
38 Steel Tube 1
39 Chain Stop 1
40 Swing Arm 1
41 Cushion 1
42 Chain Stop Adjustment Knob 1
43 Chain Stop Lock Nut 2
44 Vise Base 1
45 Nut 1
46 Screw 2
47 Mat 2
48 Inner Vise Clamp 1
49 Chain Wheel 2
50 Outer Vise Clamp 1
51 Chain Roller 2
52 Screw 2
53 Clamp Lock Nut 1
54 Clamp Plate 1
55 Inner Panel 1
56 Spring 3
57 Central Pin 3
58 Mat 2
59 Bolt 1
60 Snap Spring 1
61 Draw Spring 1
62 Angle Adjustment Knob (not shown) 1

Page 15For technical questions, please call 1-888-866-5797.Item 68221
SAFETYOPERATIONMAINTENANCE SETUP
Assembly Diagram
1
2
3
4
6 7 8 9 10 11 12 13 14 15 16 17 18
19
20
21
22
23
24
25
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48 49 50 51 52 53 54
55
56
57
58
59
60
61

Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797