CHIEF 672000 User manual

Self-Tightening
Clamps
USERS MANUAL
2002 © Chief Automotive Systems, Inc.

SELF-TIGHTENING CLAMPS
USERS MANUAL
CHIEF’S LIMITED ONE-YEAR
WARRANTY & LIABILITY
Chief Automotive Systems, Inc. warrants for one year from date of installa-
tion and/or purchase any of its products which do not perform satisfactorily
due to defect caused by faulty material or workmanship. Chief’s obligation
under this warranty is limited to the repair or replacement of products which
are defective and which have been misused, carelessly handled, or defaced
by repair or repairs made or attempted by others.
CHIEF AUTOMOTIVE SYSTEMS, INC. DOES NOT ASSUME RESPONSI-
BILITY FOR ANY DEATH, INJURY OR PROPERTY DAMAGE RESULTING
FROM THE OPERATOR’S NEGLIGENCE OR MISUSE OF THIS PROD-
UCT OR ITS ATTACHMENTS. CHIEF MAKES NO WRITTEN, EXPRESS
OR IMPLIED WARRANTY WHATSOEVER OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE REGARDING
THE EQUIPMENT OR ANY PART OF THE PRODUCT OTHER THAN THE
LIMITED ONE-YEAR WARRANTY STATED ABOVE.
Returned merchandise requires a “RETURNED GOODS AUTHORIZATION
NUMBER” on the package. Authorization numbers can be obtained by call-
ing or writing the Customer Service Department, Chief Automotive Systems,
Inc. No returned merchandise will be accepted without an authorization
number. All returned merchandise must be shipped freight prepaid (and may
be subject to a 15 percent handling and restocking charge) to:
Chief Automotive Systems, Inc.
Attn: Returned Goods Dept.
1924 E. Fourth St.
P.O. Box 1368
Grand Island, Ne. 68802-1368
308-384-9747
Your Authorized
Chief Automotive Systems, Inc.
Representative
or

SELF-TIGHTENING CLAMPS
USERS MANUAL
SELF-TIGHTENING CLAMPS
The self-tightening clamps identified below are designed
for use with Chief pulling systems. Improper application
may cause serious injury, damage to the clamp and void
any applicable warranties.
IMPORTANT: The procedures in this manual are appli-
cable to Chief’s 1 1/2” self-tightening clamp (Pt. No.
672000 - Figure 1) and 2” self-tightening clamp (Pt.
No. 672034 - Figure 2). They are also applicable to
the Dyna-Mo Jr. Clamp (Pt. No. 619072), Angle Bite
Clamp (Pt. No. 619071), and Bite -Tite C-Clamp (Pt.
No. CL1290CA) which are also available from Chief.
PREPARATION
Treat clamps (see Figure 3) with a small amount of anti-seize compound when new and anytime the compound is not pres-
ent (after cleaning, etc.). Treat the areas indicated in Figures 4 - 6 below.
NOTE: A light surface coating of anti-seize compound is enough. Too much may cause the wedge to slide too easily, result-
ing in the clamp biting too deeply into the metal to which it is attached.
APPLICATION
1) Place the clamp in the desired position and hand-tighten enough to hold it in place.
WARNING: Tighten only to the point the clamp will remain in place. Use a ratchet and socket if necessary (see
Figure 7), but tighten only to the point the clamp will remain in place. Overtightening may cause the
bolt or clamp to break under pulling pressure resulting in flying parts and severe personal injury
and/or death.
2) Attach tower chain and remove the slack from the chain.
3) With slight pressure on the chain, tap the rear corner of the clamp with a hammer as shown in Figure 8. This will
assist wedge movement before applying higher pulling pressure.
4) NEVER USE AN IMPACT WRENCH ON CLAMP BOLT! (See Figure 9.) The clamp is designed to self-tighten as pres-
sure is applied.
Figure 1 Figure 2
Figure 3 Figure 4 Figure 5 Figure 6
Figure 7 Figure 8 Figure 9
1 1/2” Self-Tightening
Clamp
2” Self-Tightening
Clamp

Form STC (8/02)
Part No. 619013
P.O. Box 1368
Grand Island, Nebraska 68802-1368
Phone [phone]
Fax [phone]
INTAIRCO S.A.R.L.
CA de TREMBLAY CHARLES DE GAULLE
18, rue Henri FARMAN
93297 TREMBLAY EN FRANCE CEDEX
TEL [phone]
FAX [phone]
www.chiefautomotive.com
Chief reserves the right to alter product specifications and/or
package components without notice.