Child Craft Long Beach F02109 User manual

Model Covered: F02109
Long Beach Double Dresser
F02109.59
2018 / 12
10861
AB20301A
Assembled Double Dresser
White
Light Gray
Dark Gray

ABC
D
PQS
TUV
X-W X-X X-Y X-Z
2
W
R
B. Division 92103465 1
C. End Panel - Right 92103466 1
D. Top Panel 92103467 1
E. Lower Back 92103468 1
F. Top Back Panel 92103469 1
G. Lower Back Panel 92103470 1
H. Front Rail 92103471 2
I. Bottom Front Rail 92103472 1
J. Top Front Rail 92103473 1
K. Drawer Front 92103474 6
L. Drawer Back 92103475 6
M. Drawer Bottom 92103476 6
N. Drawer Right Side 92103447 6
O. Drawer Left Side 92103448 6
P. Dowel Ø8 92103477 43
Q. Dowel Ø6 92103477 16
R. Flat Head Screw 92103477 2
S. Flat Head Screw 92103477 67
Z. Handle Screw 92103450 12
T. Minifix Screw 92103477 6
U. Flat Head Screw 92103477 31
V. Glide Screw 92103360 48
X. Glides 92103360 6
Y. Handle 92103450 6
W. Minifix Round Nut 92103477 6
AA. Pan Head Screw 92103359 2
BB. Pan Head Screw 92103359 2
CC. Bracket 92103359 2
E
F
G
HIJ
KLMN
O
CC
BB
AA
DD
Anti-Tip Kit Parts
Hardware Package
YZ
A. End Panel - Left 92103464 1
DD. Restraint Strap 92103359 1
Carefully remove and lay out all hardware and parts.
Check quantities and match the parts list.
Construct case on an even flat floor.
Note: during the assembly process whenever using
screws or bolts, check each with the parts list by letter
and size identification.
Be sure to use the proper size specified in the assembly
directions. If any parts are missing or broken or you need
assistance with assembly.
DO NOT return your product to the dealer. Please
identify the furniture by the model number identification
stamped on the assembly when you call or write to
Foundations. Make note of all identification numbers and
include this information with your request.
DO NOT Substitute Parts!

Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
T
3
(6x)
T
T
T
T
T
T
P
P
P
P
P
E
B
H
I
O
N
J
DA
C

V
X-Z
X-Z
V
X-W
V
4
V
X-Z
V
V
X-Z
V
VC
C
V
X-W
V
X-W
V
V
X-W
V
V
A
A

V
X-Z
X-Z
V
V
X-W
V
180º
First
Second
STEP 5
5
B
V
X-Z
V
V
X-Z
V
V
B
V
X-W
V
V
X-W
V
B
V
X-W
!
B

S
S
R
(2x)
STEP 6
STEP 7
6
H
C
R
R
E
B

STEP 8
W1st
2nd
W1st
2nd
S
STEP 9
7
S
S
(2x)
S
S
w
H
I
J

W1st
2nd
W1st
2nd
STEP 10
STEP 11
W
8
(2x)
S
S
S
A

STEP 11
STEP 12
9
S
S
S
W
S
S
S
W
W
(2x)
(3x)
S
S
D
S
S
S
(26x)
U
(5x)
U
F
GF
G
S

S
S
V
V
X-Y
X-Y
V
X-X
Z
Y
STEP 13 (2x)
10
V
S
S
V
V
Y
Z
Z
Z
N
O
M
L
S
S
S
( K ) White

S
S
S
V
V
X-Y
X-Y
V
X-X
Z
Y
STEP 14 (4x)
11
V
S
S
S
S
V
V
Y
Z
Z
Z
K
N
O
M
L

FURNITURE
FRAME
FURNITURE
FRAME
FURNITURE
FRAME
WALLBOARD
DD
CC
WALLBOARD WALLBOARD
AA
AA CC
BB
CC
BB
STEP 15
12
ANTI-TIP RESTRAINT ASSEMBLY INSTRUCTION
Anti-tip Restraint Assembly is REQUIRED in order to complete construction of this product.
When properly installed, this hardware can provide additional protection against the unexpected tipping of
furniture.
ASSEMBLY INSTRUCTIONS:
1) Attach one bracket ¨CC¨ to back of unit using ( 2 ) of screw ¨BB¨ as shown in diagram below.
2) Place the furniture against wall at the desired location in your room. Mark the location on the wall which will
position a second bracket ¨CC¨ approximately 1" lower than the one attached to the unit.
3) Remove furniture from desired location to allow installation of a second bracket ¨CC¨ on wall.
Attach the second bracket ¨CC¨ to the wall. Note-if a ¨Hollow Wall Anchor Bolt¨ system (not provided) is
used, it will be necessary to purchase a type that is appropriate for your wall construction and will also
be compatible with bracket ¨CC¨.
If bracket ¨CC¨ is mounted into a wall stud then it may be necessary to bore a 5/64" diameter x 1" deep
pilot hole into the wall at the location of each of the 2 screw holes in bracket ¨CC¨. This will assist in an
easier installation of the 2 screws ¨AA¨.
4) Move furniture back into the desired location approximately 3" away from the wall.
5) Lace an end of the nylon restraint strap ¨DD¨ through each bracket. Bring both ends together and
slide the beaded end of the strap through the keyhole shaped slot on the other end. Pull down on the
beaded end until it snap-locks into the keyhole.
6) Move furniture against wall and continue to adjust nylon restraint strap to
secure unit snugly against wall.
7) Check to make sure the strap is securely laced and locked to the
brackets.

STEP 16
13
Please review warning label inside of top drawer.
White
Light Gray
Dark Gray

14
MAINTENANCE:
Upon completion of the assembly, check to make sure all screws, bolts and connectors are tightened and
secure.
Periodically check furniture for damaged hardware, loose joints, missing parts or sharp edges before and
after assembly and frequently during use.
DO NOT use furniture if any parts are missing or broken.
If any parts are missing, broken or you need assistance DO NOT return furniture to your dealer.
Call Foundations at 330.722.5033 and include model identification numbers recorded on page 1.
DO NOT substitute parts.
CLEANING:
Mix a mild solution of gentle dishwashing soap and water, apply to surface using a clean cloth lightly
dampened in the solution. Rinse well with clear water using a soft clean cloth, then dry all surfaces with a
soft dry cloth.
DO NOT use abrasive cleaners or any cleaners with harsh chemicals that would contact a child’s
skin, scouring pads, steel wool or coarse rags. This furniture should be treated the same as any
fine furniture.
STORAGE:
When storing furniture use caution as extreme temperature or humidity changes could be harmful.
Use caution when a vaporizer is in use. Always aim vapor stream away from furniture as well as
away from any wood furniture item.
After completing the assembly the user is advised to read and be aware of
ALL WARNINGS, CAUTIONS, CLEANING, STORAGE USE AND MAINTENANCE. Please store the
complete set of assembly directions for future referral.