Chipolino MY SIZE User manual

This child restraint system is manufactured in compliance
with the requirements of Regulation No 129 of the Economic Commission
for Europe of the United Nations (UN/ECE) — Uniform provisions concerning
the approval of enhanced Child Restraint Systems used on board of motor
vehicles (ECRS), the provisions of the Product safety Directive 2001/95/EU of
the European Parliament and The Council as well as the Consumer Protection
Law of Bulgarian Legislation.
IMPORTANT! KEEP THIS MANUAL FOR FUTURE REFERENCE!
INSTRUCTION MANUAL FOR
USE OF CHILD RESTRAINT SYSTEM
„MY SIZE”

1
N O T I C E
Size range: 40-105 cm
This is an “i-Size” Child Restraint System. It is approved to Regulation No.129, for use in,
“i-Size compatible” vehicle seating positions as indicated by vehicle manufacturers in the vehicle
users’ manual.
If in doubt, consult either the child restraint manufacturer or the retailer.
Size range: 100-135 cm
This is an “i-Size” Booster seat Child Restraint System. It is approved to Regulation No.129,
for use primarily in, “i-Size seating positions” as indicated by vehicle manufacturers in the vehicle
users’ manual.
If in doubt, consult either the child restraint manufacturer or the retailer.
Size range: 135-150 cm
This is an “i-Size” Booster seat Child Restraint System. It is approved to Regulation No.129, for
use primarily in, “i-Size seating positions” as indicated by vehicle manufacturers in the vehicle
users’ manual.
If in doubt, consult either the child restraint manufacturer or the retailer.
CAUTION! The child restraint is suitable for use in vehicles, equipped with APPROVED 3-POINT
SAFETY BELTS WITH RETRACTOR in compliance with ECE R16 of (UN/ECE).
Car seat “MY SIZE” is suitable for children with height 40-150 cm, age 0-12 years.
Position of car seat Child’s height Approx age of child Car seat installation
REARWARD facing 40-105 cm 0-4 years
ISOFIX
+
Top tether
+
Car seat safety belt
for secure the child
FORWARD facing 76-105 cm 15 months - 4 years
ISOFIX
+
Top tether
+
Car seat safety belt
for secure the child
FORWARD facing 100-150 cm 3-12 years
ISOFIX
+
3-point vehicle belt

1
2
2
NEVER INSTALL THE CAR SEAT IN
VEHICLE WITH 2-POINT BELT! INSTALL IT ONLY IN
VEHICLE WITH 3-POINT BELT!
DIAGONAL BELT
LAP BELT
Rearward facing installation of the car seat
Height of the child: 40-105 cm
Forward facing installation of the car seat
Height of the child: 76-150 cm
DO NOT FORGET THAT NO RESTRAINT SYSTEM CAN PROVIDE
ABSOLUTE PROTECTION IN CASE OF A CRASH OR ROAD ACCIDENT!
DRIVE WITH CARE WHEN THERE IS A CHILD IN YOUR VEHICLE!
IN ORDER TO ENSURE THE SAFETY OF YOUR CHILD,
FOLLOW EXACTLY THE INSTRUCTIONS AND SAFETY
RECOMMENDATIONS IN THIS MANUAL!
MISUSE OF THE CAR SEAT WILL CONTRIBUTE TO REDUCING ITS SECURITY
AND SAFETY FEATURES! FAILURE OF THE GUIDELINES OF THIS
INSTRUCTION INCREASES THE RISK OF SERIOUS INJURY OR DEATH!
CAUTION !
1. NEVER INSTALL THE CAR SEAT IN “FORWARD FACING” POSITION BEFORE THE
CHILD’S AGE EXCEEDS 15 MONTHS!
2. DO NOT PLACE THE RESTRAINT SYSTEM ON A VEHICLE SEAT EQUIPPED WITH AIR
BAG! THIS MAY RESULT IN DEATH OR SERIOUS! Review the instructions of the vehicle
for information about airbags and conditions of transportation of children.
3. DO NOT USE ANCHOR POINTS OTHER THAN THE ONES DESCRIBED IN THIS MANUAL
AND MARKED ON THE RESTRAINT SYSTEM!
1
2
!

3
Do not install on seat, equipped with air bag.
Place the car seat ONLY on a vehicle seat with a 3-point seat safety belt.
?1
?1
?2
?2
CAUTION! WARNINGS!
CAUTION! NEVER LEAVE YOUR CHILD UNATTENDED!
CAUTION! DO NOT USE ANCHOR POINTS OTHER THAN THE ONES DESCRIBED IN THIS
MANUAL AND MARKED ON THE RESTRAINT SYSTEM.
CAUTION! WHEN YOU INSTALL THE CAR SEAT IN POSITION „REARWARD FACING“, NEVER
PLACE IT ON PASSENGER SEAT, EQUIPPED WITH AIRBAG! THIS MAY LEAD TO SERIOUS
INJURY OR DEATH!
CAUTION! NEVER INSTALL THE CAR SEAT IN DIRECTION OF NORMAL MOVEMENT OF THE
VEHICLE AND POSITION OF THE CHILD "FORWARD FACING" BEFORE THE CHILD EXCEEDS
15 MONTHS OLD!
CAUTION! THE VEHICLE SAFETY BELTS WHICH HOLD THE CAR SEAT TO THE PASSENGER
SEAT MUST BE TIGHTENED AND FIXED!
CAUTION! THE CAR SEAT SAFETY BELTS MUST BE PROPERLY ADJUSTED ACCORDING TO
CHILD’S HEIGHT, NOT TWISTED AND SNUG WELL AGAINST BABY’S BODY.
THE LAP BELT MUST BE PLACED LOW DOWN, SO THAT THE PELVIS IS FIRMLY ENGAGED
WITHOUT PRESSING!
CAUTION! DO NOT MAKE CHANGES, ADDITIONS OR MODIFICATIONS ON THE CAR SEAT
WITHOUT THE APPROVAL OF THE NOTIFYING AUTHORITY ! IT IS DANGEROUS NOT TO
KEEP STRICTLY THE INSTRUCTIONS GIVEN BY THE MANUAFACTURER!
CAUTION! KEEP AWAY FROM FIRE!
Installation in the vehicle and securing the child in the car seat to be done only by adult!
The hard parts and the parts of the child restraint made of plastic should be located and installed
so that when the vehicle is in normal use, they can not be trapped by a sliding seat or in a door of
the vehicle.
Do not allow the safety belts of the car seat and the vehicle to be twisted, frayed or torn, latches and
 locks(buckles)mustbealwaysingoodorderandrmlyxed.
 Ifyounduncertaintyordefectinthestructure,latches,strapsorlockingmechanismsofthecar
seat or ISOFIX attachments , discontinue usage until removal of the damaged parts and
replacement with new ones.
After a violent impact the car seat and belts may be damaged, therefore, it is recommended to
replace the car seat with a new one.
 Neveruseasecondhandchildrestraint.Itmayhavesu󰀨eredstructuraldamage,whichmaymake
 thechildrestraintextremelydangerous.

4
PRODUCT FEATURES
This is I-Size child restraint system, suitable for children with height 40-150 cm, age 0-12 years.
The child restraint rotates 360 degrees on the base;
Backrest recline;
Headrest height adjustment;
5-point safety harness on the restraint;
Additional soft pads;
Do not use this car seat without its seat cover and do not replace it with a new one, unless supplied
by the manufacturer. The fabric parts are integral parts of the restraint system and its safety
features!
Any luggage or other objects that could cause injury in the event of a collision must be well secured.
Remove or secure at a safe distance from the seat and child any luggage that may cause injury in
the event of a sudden stop or accident while driving.
 Alwayscheckthattheseatisrmlyattachedtothevehicleseat,evenwhenyouarenotplacinga
child in it. A loose car seat, even without a child in it, can cause injury in the event of a collision.
 Donotputadditionalpadsexcepttheonessuppliedfromthemanufacturer!
Do not use spare parts and other components not supplied by the manufacturer. The manufacturer
assumes no responsibility for safety in the event that are used spare parts other than original.
Keep the instructions for use in the space provided in the car seat or in the vehicle in which you are
going to use the car seat.
 Donotexposethecarseattodirectsunlighttopreventthechildfromburning,deformingthecarseat
and especially the plastic parts.
The car seat does not replace the child's cot or bed. When a child needs a sleep, you have to place
him/her in a suitable baby stroller, baby crib or bed.
Do not attach objects with long cords or strings on the car seat in order to avoid danger of
 su󰀨ocation!
Never place the car seat on beds, couches or similar soft surfaces!
Do not allow children to play with the product!
Do not remove stickers and warnings – they contain important information!
The packaging of the product must be kept out of the reach of children at the time of and after
unpacking in order to avoid the risk of strangulation!

5
MAIN PARTS
ISOFIX attachment
anchors
Fabric cover
Soft pad
Side protection
5-point safety belt
Strap for belt’s
length adjustment
Level to rotate
the seat
Handle to adjust the
head support’s height
Adjustable head support
Shoulder belts
Button to adjust
the belt’s length
Buckle for top
tether adjustment
Top tether
Cover’s lock
Cover
ISOFIX button
INSTRUCTIONS FOR USE OF THE CHILD RESTRAINT SYSTEM
IMPORTANT!
• Followexactlytheinstructionsandsequenceofinstallationstepsanduseoftheproductdescribed
 inthetextandguresofthismanual.
• Checkthesecurityofxingaftereachoperation!
• ALWAYS CHECK THE SECURITY OF FIXING OF THE SAFETY BELTS!
• After each installation make sure that the seat belts are not twisted and they are in the correct
position.

6
CHILD’S HEIGHT 40-105 cm
INSTALLATION OF THE CAR SEAT IN “REARWARD FACING” POSITION
ISOFIX + TOP TETHER + 5-POINT BELT OF CAR SEAT
ISOFIX guide
click
attachmnet point

7
“щрак”

8
1. Pull the handle to adjust the recline.
2. Set in required position – 1, 2, 3, 4.
3. PullthelevelandadjusttheseatinREARWARDfacingposition(g.4).
4. SelectthelyingpositioncorrecpondingwithREARWARDfacing(g4).
ATTENTION! Make sure that your vehicle is equipped with ISOFIX attachment points!
5. Install the ISOFIX guide to the ISOFIX attachmnet point of vehicle.
6. ReleasetheISOFIXanchorsandsetthemmaximumout.
7. Insert ISOFIX anchors of car seat to ISOFIX attachment point of vehicle.
8. Youmusthearclicksoundbyxing.
9. CAUTION!ISOFIXanchorsarexedwhenbothofthemarefullygreen.
Note: If indicators are red, do the installation again following the above described sequence of
actions.
10. Press the car seat until it reaches the backrest of vehicle’s seat.
11. and12TrytopullthecarseattoassurethatISOFICanchorsarexedtoISOFIXattchmentpointof
vehicle.
13.Pressthebuttonofbuckleforadjustmentoftoptether’slengthandpullitatmaximum.
14. Thread the top tether belt through the one of the side guides of car seat.
15. Attach the hook of top tether to the attachmnet point of your vehicle. Note: Belt must not be twisted.
16. Tighten the top tether.
17. After tightning indicator of top tether belt must be fully green.
Note: If indicator is red, do the installation again following the above described sequence of actions.
18.Makesurethatcarseatisstablexed.
19, 20 Press the button for belts adjustment and at the same time pull the shoulder belts towards you.
21, 22 Press the button at central buckle to release the belts and place the child in car seat.
23, 24 Pull the handle for head rest adjustment and set the head support in suitable position (see the
 gure-correctheight).
25, 26 Join the shoulder belts into the central buckle. Pull the strap that adjusts the length of belts so that
the belts hold will the body of child without bringing pressure and discomfort to the child.
Recommened space between child’s body and belts is 1-2 cm.
PLACES AND WAYS TO ATTACH THE TOP TETHER TO VEHICLE
Placestoattachtotoptethertodi󰀨erentvehiclescanbelocatedatoneoftheshowningure–A,
B, C or D. Before installing the car seat, you must check this in instruction manual of the vehicle.
A
BC
D

9
ATTENTION!
!
For child’s height:
• 40 up to 75 cm use soft pad of the seat and
3D pillow of the waist.
• 76 up to 80 cm use only the soft pad of the
seat.
CHILD’S HEIGHT 76-105 cm
INSTALLATION OF THE CAR SEAT IN “FORWARD FACING” POSITION
ISOFIX + TOP TETHER + 5-POINT BELT OF CAR SEAT
Soft pad
3D pillow
for the waist
click
ISOFIX guide ISOFIX button
attachmnet point

10

11
1. ATTENTION! Make sure that your vehicle is equipped with ISOFIX attachment points!
Install the ISOFIX guide to the ISOFIX attachmnet point of vehicle.
2. ReleasetheISOFIXanchorsbypressingtheISOFIXbuttons.Setthemmaximumout.
3. Insert ISOFIX anchors of car seat to ISOFIX attachment point of vehicle.
4. Youmusthearclicksoundbyxing.
5. CAUTION!ISOFIXanchorsarexedwhenbothofthemarefullygreen.
Note: If indicators are red, do the installation again following the above described sequence of
actions.
Adjust the recline in position 1, 2, 3 or 4.
6. Press the car seat until it reaches the backrest of vehicle’s seat.
7. and8TrytopullthecarseattoassurethatISOFIXanchorsarexedtoISOFIXattchmentpointof
vehicle.
9. Pressthebuttonofbuckleforadjustmentoftoptether’slengthandpullitatmaximum.
10. Attach the hook of top tether to the attachmnet point of your vehicle. Note: Belt must not be twisted.
11. Tighten the top tether.
12. After tightning indicator of top tether belt must be fully green.
Note: If indicator is red, do the installation again following the above described sequence of actions.
13.Makesurethatcarseatisstablexed.
14, 15. Press the button for belts adjustment and at the same time pull the shoulder belts towards you.
16, 17 Press the button at central buckle to release the belts and place the child in car seat.
18, 19, 20 Pull the handle for head rest adjustment and set the head support in suitable position
 (seethegure-correctheight).
21, 22 Join the shoulder belts into the central buckle. Pull the strap that adjusts the length of belts so that
the belts hold will the body of child without bringing pressure and discomfort to the child.
Recommened space between child’s body and belts is 1-2 cm.
ATTENTION!
!
For child’s height:
• 76 up to 80 cm use only soft pad of the seat
Soft pad
Soft pad

12
CHILD’S HEIGHT 100-150 cm
INSTALLATION OF THE CAR SEAT IN “FORWARD FACING” POSITION
3-POINT BELT OF VEHICLE
“click”
click
lap belt

13
1. Press the button at central buckle to release the belt.
2. Lifttheupperpartfotheseatcoverasgureshows.
3. Press the button for belts adjustment and at the same time pull the shoulder belts towards you.
4. Unfastenthedownpartoftheseatcoverandplaceitdownasgureshows.
5. Fixthebeltsandcoverthemwithbothpartsoftheseatcover.
6. Place the central buckle in car seat’s slot.
7. Remove the soft pad.
8. Place the child in car seat.
9. Pull the handle for head rest adjustment and set the head support in suitable position
 (seethegure-correctheight).
10. Thread the lap belt through the guide under the armrest of car seat and above the legs of the child.
Make sure the belt snugs will the child’s pelvis.
11. Thread the diagonal belt through the guide at the upper part of backrest.
12. Lock the 3-pont belt of vehicle into the buckle of vehicle’s seat.
CAUTION! Make sure that belt is not twisted.
CHILD’S HEIGHT 100-150 cm
INSTALLATION OF THE CAR SEAT IN “FORWARD FACING” POSITION
3-POINT BELT OF VEHICLE + ISOFIX
click
ISOFIX guide
ISOFIX button
attachment point

14
ATTENTION! Make sure that your vehicle is equipped with ISOFIX attachment points!
1. Hide the car seat belts and remove the soft pad.
2. Set the recline is position 1.
3. Install the ISOFIX guide (option) to the ISOFIX attachmnet point of vehicle.
4. ReleasetheISOFIXanchorsbypressingtheISOFIXbuttons.Setthemmaximumout.
5. Insert ISOFIX anchors of car seat to ISOFIX attachment point of vehicle.
6. Youmusthearclicksoundbyxing.
7. CAUTION!ISOFIXanchorsarexedwhenbothofthemarefullygreen.
Note: If indicators are red, do the installation again following the above described sequence of
actions.
8. Press the car seat until it reaches the backrest of vehicle’s seat.
9. and10TrytopullthecarseattoassurethatISOFIXanchorsarexedtoISOFIXattchmentpointof
vehicle.
11. Place the child in car seat.
12. Pull the handle for head rest adjustment and set the head support in suitable position
 (seethegure-correctheight).
13. Thread the lap belt through the guide under the armrest of car seat and above the legs of the child.
Make sure the belt snugs will the child’s pelvis.
14. Thread the diagonal belt through the guide at the upper part of backrest.
15. Lock the 3-pont belt of vehicle into the buckle of vehicle’s seat.
CAUTION! Make sure that belt is not twisted.
click

15
CARE AND MAINTENANCE
Clean the fabrics, plastic parts and metal parts with damp cotton cloth or sponge and mild soap
 Fabriccoverandsoftpadsmaybehandwashedat30Сusingmilddetergent!
Do not bleach! Do not tumble dry! Do not machine wash! Do not iron!
Do not use abrasive, bleach or other aggressive detergents.
Always after cleaning leave the car seat fully dry and after that use it or store it.
Harnesses must be cleaned with damp cloth and mild soap!
Do not wet or remove the stickers. They contain important information!
 Alwaysstoreyourcarseatindoors–ondryandcleanplace.Donotexposetodirectenvironment
 inuence-sun,rain,moistureandhightemperatureintervals.
Please, contact your authorized dealer for problems connected with the use or repair.
Fabric:
Outer: 100% polyester
Filling: 100% polyester
Materials used:plastic,metal,textile
STKMS022xxxx
1. Hide the car seat belts and remove the soft pad.
2. Remove the fabric cover of head support.
3. Unfasten and remove the fabric cover under the head support.
4. Remove all the rest of seat fabric cover.
To place the cover back, do the same actions in opposite order.
REMOVING AND PLACING THE SEAT COVER
Soft pad

16
List of vehicles that are suitable for
installation of child restraint system “MY SIZE”
as booster seat for specic vehicle.
Vehicle Model ISOFIX 3-point belt
of the vehicle

17
Vehicle Model ISOFIX 3-point belt
of the vehicle

18
Vehicle Model ISOFIX 3-point belt
of the vehicle

Bulgaria, Plovdiv, Str. Golyamokonarsko shosse № 1
www.chipolino.com