Chipsee PPC/EPC-A8-70-HB-C User manual

www.chipsee.com
www.chipsee.com
PPC/EPC-A8-70-HB-C
User Manual
Release 1.0

www.chipsee.com
www.chipsee.com
Chipsee Products Naming Rules
CS10600T070E-C211
CS10600T070P-C211
CS Chipsee Product Abbreviate
10
Horizontal Resolution
80 Means 800 Pixel
10 Means 1024 Pixel
12 Means 1280 Pixel

www.chipsee.com
www.chipsee.com
600
Vertical Resolution
480 Means 480 Pixel
600 Means 600 Pixel
768 Means 768 Pixel
800 Means 800 Pixel
T(F) Product based on TI(FreeScale) CPU
070
LCD dimension
050 Means 5.0 Inch
070 Means 7.0 Inch
080 Means 8.0 Inch
097 Means 9.7 Inch
101 Means 10.1 Inch
104 Means 10.4 Inch
E
Means Embedded PC or Panel PC
E Means Embedded PC without Case
P Means Panel PC with Case
C
Means Touch type
R Means Resistive Touch
C Means Capacitive Touch
2
Means LCD Brightness
1 Common brightness
2 High Brightness
1PCB Version
Baseboard PCB Version Number
1PCB Version
SOM Module PCB Version Number

www.chipsee.com
www.chipsee.com
Hardware Features
Key features:
Sitara Core AM3354ZCZ100
CPU ARM Cortex A8, 1GHz
RAM 512MB DDR3
eMMC 4GB
Storage uSD card, supports up to 32GB SDHC
Display 7.0 Inch LCD,1024 x 600 Pixel Resolution
High Brightness,500nit
Touch C: Capacitive Touch (Five-Point)
R: Resistive Touch (Four-Wire)
USB 2 x USB 2.0 Host
(can be customized to HOST or OTG)
LAN 1 Channel 100M LAN
Audio 3.5mm Audio In/Out Connector
Buzzer 1
RTC Yes
RS232 2 Channels
RS485 2 Channels *

www.chipsee.com
www.chipsee.com
CAN 1 Channel *
Can Customized to 2 Channel
GPIO 8
WiFi/BT On Board WIFI/BT, Optional. Not mount on
by default
Power Input 6~42V DC
Current @ 12V 600 mA max
Power Consumption 6W Typical
Working
Temperature -20°C to +70°C
OS Android, TI Linux, Debian, Angstrom
Dimension CS10600T070E-C211:190 x 107.8 x 29mm
CS10600T070P-C211:206 x 135 x 29.8mm
Weight CS10600T070E-C211: 340g
CS10600T070P-C211: 680g
* The RS485 and CAN channels may be customized to the
following arrangements:
2 x RS485, 1 x CAN(Default)
1 x RS485, 2 x CAN
CS10600T070E-C211

www.chipsee.com
www.chipsee.com
Figure 1 Top View
Figure 2 Back View

www.chipsee.com
www.chipsee.com
CS10600T070P-C211
Figure 1 Top View

www.chipsee.com
www.chipsee.com
Figure 2 Back View
Power Input Connector
The product CS10600T070E/CS10600T070P uses a wide range of
power Input: DC 6~42V. And the total power consumption is
normally around 6W. The Power Input Connector is 3 pin 3.81mm
Screw Terminal connector as Figure 5 Power Input Connector and
Figure 4 Back View. It is labelled as P6 on the PCB, P2 on the
backside of the metal case. The character “+” means power
Positive input, The character “–” means power Negative input.

www.chipsee.com
www.chipsee.com
The character “G” means system Ground. Table 2 has detailed
descriptions about the connector definition.
(a) CS10600T070E
(b) CS10600T070P
Figure 5 Power Input Connector
Table 1
Power Input Pin Definition:
Pin Number Definition Description
Pin 1 Positive Input Connect to DC Power Positive
Terminal
Pin 2 Negative Input Connect to DC Power Negative
Terminal

www.chipsee.com
www.chipsee.com
Pin 3 Ground Connect to Power System Ground
Please note:
The system ground “G” has been connected to power Negative “–”
on board.
Capacitive Touch
Product CS10600T070E/CS10600T070P uses capacitive touch, As
Figure 6 shows.
Figure 6 Capacitive Touch Connector
Attention:
Capacitive touch is very sensitive to power noise. Ripple
voltage/current from the power adapter will cause the LCD
ripples, and will also cause the capacitive touch malfunction:
If you use the APK Multi-Touch under Android to test, you can
find the touch point float. There are several ways to solve
this problem:
1) Use a high quality power adapter. Or use battery to

www.chipsee.com
www.chipsee.com
provide the power like cell phone or tablet PC.
2) If the user’s power adapter isn’t good enough, there’s
another effective method to solve this problem: Make sure the
CS10600T070E-C211 Power Input Connector P6 Pin 3 really
connect to user “Power System Ground”. This method can
eliminate the problem totally. The user can also use another
method to test this problem: Touch the GND of CS10600T070E-
C211 by one hand, the other hand operates on the Capacitive
Touch Screen. In this case, the user’s body acts as the Power
System Ground.
CAN+RS485+RS232 Connector
The RS232 / RS485 / CAN connector is a 12 Pin 3.81mm Screw
Terminal connector.
It is defined as P16 on the PCB, P1 on the backside of the
metal case, as shown in Figure 4 Back View and Figure 7 RS232
/ RS485 / CAN Connector.

www.chipsee.com
www.chipsee.com
Figure 7 RS232 / RS485 / CAN Connector
As for the definition of every Pin, please refer to Table 3.
This product can be customized to inherit two CAN channels. If
two CAN channels are needed, please contact us.
RS232 / RS485 / CAN Pin Definition
Table 3
RS232 / RS485 / CAN Pin Definition:
Pin Number Definition Description
Pin 1 GND Isolated Ground Output
Pin 2 CAN_L DCAN0 of CPU,CAN L Signal
Pin 3 CAN_H DCAN0 of CPU,CAN H Signal
Pin 4 A2 UART4 of CPU, RS485 A Signal
Pin 5 B2 UART4 of CPU, RS485 B Signal
Pin 6 A1 UART2 of CPU, RS485 A Signal
Pin 7 B1 UART2 of CPU, RS485 B Signal

www.chipsee.com
www.chipsee.com
Pin 8 TXD2 UART1 of CPU,RS232 TXD Signal
Pin 9 RXD2 UART1 of CPU,RS232 RXD Signal
Pin 10 TXD1 UART0 of CPU, RS232 TXD Signal
Pin 11 RXD1 UART0 of CPU,RS232 RXD Signal
Pin 12 +5V System +5V Power Output, No more than
1A Current output
The RS485 and CAN channels may be customized by Chipsee to the
following arrangements:
2 x RS485, 1 x CAN(Default)
1 x RS485, 2 x CAN
USB Connector
The product CS10600T070E/CS10600T070P has two USB
connectors，as Figure 8 shows. These two USB connectors can be
customized to HOST or SLAVE. All these two connectors have
been defined as HOST by default.

www.chipsee.com
www.chipsee.com
(a) CS10600T070E
(b) CS10600T070P
Figure 8 USB connector
Please note:
The OTG Connector P14 (USB0) is defined as HOST by default. If
it’s needed to be defined as SLAVE (OTG), please Remove two
0603 package 0 Ohm resistors R119 and R121 as Figure 8 shows.

www.chipsee.com
www.chipsee.com
LAN Connector
The product CS10600T070E/CS10600T070P features one channel
100Mbit Ethernet. The connector can be found on the PCB
labelled as P13 as Figure 9 LAN Connector shows.
(a) CS10600T070E
(b) CS10600T070P
Figure 09 LAN Connector

www.chipsee.com
www.chipsee.com
uSD Card
As in Figure 10, the uSD card connector is labelled as P5 on
the PCB. The device supports uSD cards up to 32GB.
(a) CS10600T070E
(b) CS10600T070P
Figure 11 TF Card (uSD) Connector
Please note: The uSD card Slot is NOT Mounted with any uSD
card by default.

www.chipsee.com
www.chipsee.com
Boot Switch
The device features a boot switch which can be used to change
the boot sequence. It is defined as SW2 on the PCB as shown in
Figure 4 Back View and Figure 11 Boot Switch. The position can
either be eMMC or SD. The device will boot from the location
that’s selected.
(a) CS10600T070E
(b) CS10600T070P
Figure 11 Boot Switch

www.chipsee.com
www.chipsee.com
Audio Connector
As Figure 12 shows, the device has one Audio Input (“Line-in”)
and one Audio (“Line-out”) Output.
(a) CS10600T070E
(b) CS10600T070P
Figure 12 Audio Connector
WiFi+BT

www.chipsee.com
www.chipsee.com
The product CS10600T070E/CS10600T070P features one WiFi+BT. As
figure 13 shows. It uses Realtech RTL8723 which integrates
WiFi and BT.
(a) CS10600T070E
(b) CS10600T070P
Figure 13 WiFi+BT module
Please note:
The WiFi/BT module is NOT Mounted by default. If the1.
user needs WiFi/BT, please contact us.
This WiFi/BT module uses USB1 channel to communicate2.
with CPU, so it will occupy the USB1 channel when
mounted on.

www.chipsee.com
www.chipsee.com
Expansion Connector
There is an Expansion Connector labelled as P18 on the PCB as
figure 14 shown, it is connected to CPU GPIO/ADC/SPI/I2C
signals。The connector is not mounted by default.
Figure 14 Expansion Connector
As for the definition of every pin, please refer to Table 4。
ATTENTION: All these signals connect to the CPU directly.
Please use it carefully or the CPU will be damaged easily.
Expansion Connector Definition
Table 4
PIN Function CPU PIN PIN Function CPU PIN
1 GND Power Ground 2 VDD_5V0 +5V Power
3 GND Power Ground 4 VDD_3V3 +3.3V Power
5 GPMC_A1 V14 6 GPMC_A3 T14
7 GPMC_A2 U14 8 GPMC_A5 V15
9 GPMC_A4 R14 10 GPMC_A7 T15