Christie Roadie HD+35K User manual

Roadie HD+35K Portrait Upgrade Kit Instruction Sheet 1 of 4
020-100778-03 Rev. 1 (03-2012)
Roadie HD+35K Portrait Upgrade Kit
Instruction Sheet
SAFETY AND WARNING GUIDELINES
HIGH VOLTAGES MAY BE EXPOSED! Always power down and
disconnect power sources prior to servicing. Once the projector is
powered down, allow the cooling fans to automatically turn OFF before
disconnecting from AC and opening the projector.
QUALIFIED SERVICE TECHNICIANS REQUIRED! All module
replacement procedures must be performed by Christie accredited
service technicians.
NON-INSULATED DANGEROUS VOLTAGES MAY BE EXPOSED! Always
disconnect from AC prior to disassembly.
OBSERVE ALL ELECTROSTATIC PRECAUTIONS! Use a grounded wrist
strap when handling electronic assemblies.
Never operate the projector (or the fans) without all the covers installed.
Failure to operate the projector in the correct portrait mode orientation
can cause severe damage to the projector.
INTRODUCTION
The Roadie HD+35K projector must be installed in a Christie rigging
frame (P/N 38-814007-XX) and suspended as not to block
ventilation. The projector can be used in portrait mode after installing
the upgrade kit. The following instructions detail the steps required
to install the portrait upgrade kit.

2 of 4 Roadie HD+35K Portrait Upgrade Kit Instruction Sheet
020-100778-03 Rev. 1 (03-2012)
KITS REQUIRED
Kit Portrait Mode Roadie (P/N 000-102632-XX) includes:
• (1) Lamp Anode Stand Assembly (P/N 000-102637-XX)
• (3) Rubber Isolator (P/N 012-100753-XX)
• (3) 10-32 Screw (P/N 012-100425-XX)
• (3) Flat washers (P/N 012-100500-XX)
• (2) Wire rope lanyard 6-inch LG (P/N 012-100997-XX)
TOOLS REQUIRED
• #2 Phillips® screwdriver
• 3/8-inch wrench
• 3/16-inch Hex driver
INSTRUCTIONS
FRONT TOP COVER
Secure the front top cover to the projector to prevent it from falling off while using in portrait mode.
Cover Should be locked when projector is in use.
1. Unlock the lid.
2. Lift lid.
3. Loop cable through slot.
4. Feed terminal end through the loop.
5. Remove screw and install terminal.
6. Reinstall screw.
7. Repeat steps 2-5 for other side.
8. Close and lock lid.

Roadie HD+35K Portrait Upgrade Kit Instruction Sheet 3 of 4
020-100778-03 Rev. 1 (03-2012)
NEW LAMP ANODE STAND
Replace the existing lamp anode stand with the new one.
1. Open lamp door.
2. Remove existing lamp anode stand.
3. Install new lamp anode stand in the orientation shown.
NOTE: 1) The opening must be farthest away from the lamp door. 2) Torque screws to 35in-lbs
(4Nm).
4. Close lamp door.

4 of 4 Roadie HD+35K Portrait Upgrade Kit Instruction Sheet
020-100778-03 Rev. 1 (03-2012)
FAN VIBRATION ISOLATORS
Replace the existing gel isolators with rubber isolators.
1. Remove back top cover and exhaust lid assembly. See section 5.3.2 Back Top Cover/Exhaust Lid
Assembly of the service manual (P/N 020-100341-XX) for more details.
2. Remove (3) nuts securing the fan bracket to the vibration mounts.
3. Remove fan bracket assembly carefully.
4. Remove the existing (3) gel isolators.
5. Install (3) new black rubber isolators.
6. Reinstall the fan bracket assembly.
7. Secure the fan bracket assembly to the new rubber isolators with the (3) 10-32 screws and the (3)
flat washers provided.
8. Torque the (3) screws to 12in-lbs (1.36Nm).
9. Reinstall the back top cover and the exhaust lid assembly.
PROJECTOR ORIENTATION
For portrait mode, the projector MUST be oriented with lens closest to
the top side up. Failure to do so will cause damage to the projector. Max
tilt ±15 degrees.
Once oriented in portrait mode, lamp alignment must be performed for optimum brightness.