Chroma Color One 100X User manual

Color One 100XTM QSG V2.1 QSG P/N: 638-0701
Quick Start Guide
Chroma-Q®
Color One 100X™
For a full product manual please visit www.chroma-q.com
Part Number: CHCONE100XXRGBA, CHCONE100XXRGBAIPSS
Model: 638-1100, 638-1150
Software Version: Engine 1.9

Color One 100XTM QSG V2.1 QSG P/N: 638-0701
1. Overview
The new Chroma-Q®Color One 100X™is a LED Par fixture with RGBA LEDs and a fully
homogenized beam. Built with an internal power supply, the fixture operates as a standalone unit
with the wireless IR Remote or controlled via an external DMX console.
The Color One 100X™is available in 2 models. The IP20 version is fitted with chassis mount
powerCon and XLR 5-Pin connectors. The IP65 version is fitted with trailing leads.
The IR Remote is included in the fixture package.
2. Safety
Caution
1. This product is for professional use only. It is NOT intended for domestic or
outdoor use.
2. The bright flash of light during power-up and continuous strobe effect may
cause epileptic seizure.
3. This product must be used with safety cable.
3. Cabling and Connection
The Color One 100X™(IP20 version) is built with chassis mount powerCon connectors for power
input/through and chassis mount XLR 5-pin for DMX input/through.
The Color One 100X™(IP65 version) is built with trailing leads for power input/through and XLR
5-pin trailing leads for DMX input/through. The chassis is ground bonded.
4. Mounting
The Color One 100X™is built with a dual yoke system for floor mounting and overhead hanging
applications. Secure the fixture with a safety bond. A provision for the fixing hold is built into the
enclosure.
5. Optics
The Color One 100X™is built with optical lens that provide a fully homogenized beam angle of
approximately ~18°.
6. Control
The control functions are accessed through the LCD display at the rear with 4 push buttons:
Back Arrow
(Enter) Stores the menu choice
Up Arrow
Increases (+) the mode level or value
Down Arrow
Decreases (-) the mode level or value
Exit
Back to the previous menu
Power-Up Display:
The software version is displayed on power up then proceeds to the Main Menu. The Main Menu
shows the model’s name, DMX status and start address, set control mode and number of assigned
DMX channels.
Display Mode:
The LCD display is backlit when you access the menu and turns off when left undisturbed for 5
seconds.
IR Remote:
The remote infrared control unit features control buttons for: On/Off, Dim Up/Down, various colors,
white and 4 effects: Full Color Scroll (Flash), Warm Color Scroll (Strobe), Fade In/Out (Fade),
Cold Color Scroll (Smooth). Set the fixture for IR Remote control by selecting IR Remote in the
menu No DMX Present. Point the IR Remote towards the fixture.
Control Menu:
To navigate the Control Menu options from the Main Menu,
•Use the Up and Down arrows to navigate the control menu options
•Press the Back arrow (Enter) to select a control menu option
•Press the Back arrow (Enter) to save the setting and display shows Done
•Press Exit to return to the Main Menu

Color One 100XTM QSG V2.1 QSG P/N: 638-0701
Main Menu
DMX Address
From the Main Menu, press Enter to adjust the DMX start address
1-Personality
Select from the following control mode options:
Mode
Display
Ch
Description
1
1-RGBA
4
RGBA
2
2-RGBAI
5
RGBA + Intensity
3
3-HSI
3
Hue + Saturation + Intensity
4
4-RGB
3
RGB (*Magic Amber)
5
5-MLED RGB
3
RGB
6
6-Master
0
Master Standalone
7
7-Slave
0
Slave Standalone
2-No DMX Present
If DMX is not detected, various output options can be selected:
1-OFF
Fixture has no light output
2-Hold Last
Fixture holds the last valid DMX state
3-IR Remote
Fixture is controlled via remote infrared control unit
4-Look 1
Fixture snaps to Blue
5-Look 2
Fixture snaps to Cyan
6-Look 3
Fixture snaps to Magenta
7-Look 4
Fixture snaps to Yellow
8-Look 5
Fixture snaps to White
3-Look Store
5 internal preset Looks are available in standalone operation.
To recall a Look in standalone operation, use the Up/Down arrows to scroll through
Look 1-5, then press Enter to recall the Look.
Looks can be recorded and assigned to Looks 1-5, and will be preserved on power
down. Looks will be returned to default settings upon reset.
To create, edit and record a look in standalone mode, go to Look Store, scroll and
select/recall from Look 1-5, use the Enter to toggle between channels and the
Up/Down arrows to adjust the values of each channel on the display, press and
hold Enter until the display shows Recorded, Look and Mode.
4-Technical
Software Version, DMX Data settings, internal Temperature and LED Calibration
values are displayed; Frequency settings of the fixture can be changed; ETC
Compatible mode.
In the Frequency menu, select from the following options: 750, 1500, 3000 and 6000
(Hz), which allows for the LED scan rate to be synchronized with the video camera
and avoid a flickering effect.
In the ETC Compatible menu, select On to activate and Off to deactivate.
5-Reset
All control menu commands are reset to factory defaults: DMX address: 1, Personality:
RGBA, No DMX Present: Hold Last, Look Store: Look 1, Frequency: 750 Hz, ETC
Compatible: Off
*Magic Amber is the term used for the unit's ability to bring in amber when mixing colors that require it.
7. Further Information
Please refer to the Chroma-Q®Color One 100XTM manual for more detailed information. A copy
of the manual can be found at the Chroma-Q®website –www.chroma-q.com/support/downloads

Color One 100XTM QSG V2.1 QSG P/N: 638-0701
Approvals & Disclaimer
The information contained herein is offered in good faith and is believed to be accurate.
However, because conditions and methods of use of our products are beyond our
control, this information should not be usedinsubstitution for customer's tests to ensure
that Chroma-Q®products are safe, effective, and fully satisfactory for the intended end
use. Suggestions of use shall not be taken as inducements to infringe any patent.
Chroma-Q® sole warranty is that the product will meet the Chroma-Q®sales
specifications in effect at the time of shipment. Your exclusive remedy for breach of
such warranty is limited to refund of purchase price or replacement of any product
shown to be other than as warranted.
Chroma-Q®reserves the right to change or make alteration to devices and their
functionality without notice due to on-going research and development.
The Chroma-Q®Color One 100XTM has been designed specifically for the lighting
industry. Regular maintenance should be performed to ensure that the products
perform well in the entertainment environment.
If you experience any difficulties with any Chroma-Q®products please contact your
selling dealer. If your selling dealer is unable to help, please contact
[email protected]. If the selling dealer is unable to satisfy your servicing needs,
please contact the following for full factory service:
Outside North America:
Tel: [phone]
Fax: [phone]
[email protected]
North America:
Tel: [phone]
Fax: [phone]
[email protected]
For further information please visit the Chroma-Q®website at www.chroma-q.com.
Chroma-Q®is a trademark, for more information on this visit
www.chroma-q.com/trademarks.
The rights and ownership of all trademarks are recognized