Chronomite RBAM-15 User manual

RBA II - RBAM-240-AU-Series/1112 Page 1/8
Lic. # W22077
Family Of Companies
Made in
the USA
• 1300 788 778
• [email protected].au
• www.rba.com.au
• 0800 722 111
• [e-mail]
• www.rbagroup.co.nz
SYDNEY
MELBOURNE
BRISBANE
PERTH
AUCKLAND
Chronomite Laboratories is a member of Morris Group International
INSTANT-FLOW MICRO WATER HEATER
INSTALLATION AND OPERATION INSTRUCTIONS
(STANDARD AUSTRALIAN MODELS)
WARNING: FOR CONTINUED SAFETY OF THIS APPLIANCE IT MUST BE INSTALLED, OPERATED AND
MAINTAINED IN ACCORDANCE WITH THE MANUFACTURER’S INSTRUCTIONS.
Table of Contents
Required items for installations not supplied
• Electrical isolation switch
• Electrical supply conduit
• Electrical supply cable
• Mini Cock and Check Valve
• Tapware
• 1/2”x8mm Dia. flexible braided stainless steel
connectors (2)
• Carpenters level
• Flat head screwdriver
• Phillips head screwdriver
Lic. # W22077
Family Of Companies
Made in
the USA
Family Of Companies
Specifications 2-3
Prior to Installation 2
Dimensional Data 3
Installation 4-6
Heater Installations 4
Electrical Installations 5
Flow Control installations 6
Troubleshooting 7
Warranty Information 8

RBA II - RBAM-240-AU-Series/1112 Page 2/8
Lic. # W22077
Family Of Companies
Made in
the USA
• 1300 788 778
• [email protected].au
• www.rba.com.au
• 0800 722 111
• [e-mail]
• www.rbagroup.co.nz
SYDNEY
MELBOURNE
BRISBANE
PERTH
AUCKLAND
Chronomite Laboratories is a member of Morris Group International
!IMPORTANT
Before installation of heater, review elec-
trical requirements needed for model of
heater selected.
NOMINAL INCOMING WATER TEMPURATURE INCREASE AT 240V
SERIES VOLTAGE 2.5 LPM 3.8LPM 5.7LPM 7.6LPM
RBAM-15 220-240 20.7°C 13.6°C 9.1°C 6.8°C
RBAM-20 220-240 27.5°C 18.1°C 12.1°C 9.1°C
RBAM-30 220-240 41.4°C 27.2°C 18.1°C 13.6°C
RBAM-40 220-240 55.2°C 36.3°C 24.2°C 18.1°C
TABLE 1
MODEL NO. WATTAGE VOLTAGE BREAKERSIZE
RBAM-15 3600 220-240 15A
RBAM-20 4800 220-240 20A
RBAM-30 7200 220-240 30A
RBAM-40 9600 220-240 40A
STANDARDS COMPLIANCE:
Product is tested and complies to AS/NZS 3350.1 (IEC 60335-1, MOD) the Standard for the Safety of Household
and Similar Electrical Appliances, Part 1 General Requirements, and to Part 2.35: AS/NZS 3350.2.35 the Particular
Requirements-Instantaneous Water Heaters. Product is tested and is WaterMark certified per AS 3498 the Standard
for Water Heaters.
Installation must comply with AS/NZS 3500.4, and AS3000, and be installed by a qualified personel.
INSTANT-FLOW SPECIFICATIONS:
Dimensions: 158 mm x 259 mm x 72 mm
Weight: 2.27 kg
Materials: ABS housing, Ryton waterways, nichrome parts
Color: White
Inlet/Outlet Fittings: Rp1/2”
Recommended Pressure Requirements: 200 kPa Minimum, 600 kPa Maximum
Max. Operating Water Temp (output): 60°C
Minimum Operating Flow Rate: 1.5LPM for RBAM-15, RBAM-20, 2.7LPM for RBAM-30, RBAM-40
Minimum Water Resistivity: 1100 Ohm.cm
Operating Ambient Temp: 5°C to 45°C
FACTORY SET TEMPERATURES:
Nominal 35°C, 40°C, 42°C, 49°C
Other temperature settings are available upon request up to 49°C. Temperature settings are not field adjustable.
42°C/49°C settings are recommended with cold water mixing Taps.
HOW INSTANT-FLOW MICRO WORKS
The heater houses a series of ingeniously designed coils that instantly heat water as it flows through the vessel.
A unique power switch automatically applies electrical current to the coils when hot water is requested. The
electrical current is not applied when the water is not in use. The micro processor is internally preset at the
factory to maintain a constant ouput temperature with varying flow rates.
SPECIFICATIONS

RBA II - RBAM-240-AU-Series/1112 Page 3/8
Lic. # W22077
Family Of Companies
Made in
the USA
• 1300 788 778
• [email protected].au
• www.rba.com.au
• 0800 722 111
• [e-mail]
• www.rbagroup.co.nz
SYDNEY
MELBOURNE
BRISBANE
PERTH
AUCKLAND
Chronomite Laboratories is a member of Morris Group International
259
27
53
145
Ø28
70
25
Ø6
245
7
7
76
51
31
158
Rp1/2”
SPECIFICATIONS
Unit Dimensions

RBA II - RBAM-240-AU-Series/1112 Page 4/8
Lic. # W22077
Family Of Companies
Made in
the USA
• 1300 788 778
• [email protected].au
• www.rba.com.au
• 0800 722 111
• [e-mail]
• www.rbagroup.co.nz
SYDNEY
MELBOURNE
BRISBANE
PERTH
AUCKLAND
Chronomite Laboratories is a member of Morris Group International
!IMPORTANT
A) All work should only be undertaken by qualified worker
B) Turn off the circuit breaker to aviod dangerous
electrical shocks.
C) Turn off the water supply
D) Flush supply line of all foreign material such as pipe
dope, pipe chips, solder, sand, teflon tape etc. making up
supply connections after working on water piping.
1
2
34
67
7
5
1. Chronomite Instant-Flow Micro
2. Isolation Switch
3. Electrical supply cable
4. Electrical supply cable
5. 1/2” mini-cock and check valve
6. Fittings (Supplied) Rp1/2”
7. 1/2” x 8 mm Dia. flexible braided
stainless steel connectors (By
others)
HEATER INSTALLATIONS:
1. Local plumbing and electrical codes must be followed in the installation of this water heater and it’s
accessories.
2. Remove cover off of water heater. Attach conduit to the conduit connection punching. Then feed cables. Do not
attach cabling.
3. Mount unit horizontally against the wall so the silver label reads correctly (See Figure 1). Use level to ensure unit
is level and mount with two screws through the flanges located on each corner using wall anchors or fasteners.
CAUTION: Heater elements may burn out if unit is not mounted horizontally.
4. Connect plumbing. Use hose with thread at cold water inlet and hot water outlet to faucet inlet connections (See
Figure 1).
5. Run water through the unit to expel all air bubbles. Check for leaks at all fitting joints.
6. Connect wiring. Attach ground wire to center terminal and active, neutral to outer terminals (See Figure 2 page5)
7. Replace cover. Follow the start up procedure on page 5. The unit is now ready for use.
Notice:
• Failure to comply with code requirements voids the warranty.
• If pressure exceeds 600kPa, a pressure limiting valve must be fitted.
• Units should be mounted as close as possible to the oulet, up to a maximum of 10m.
Figure 1 Installation Layout
INSTALLATION

RBA II - RBAM-240-AU-Series/1112 Page 5/8
Lic. # W22077
Family Of Companies
Made in
the USA
• 1300 788 778
• [email protected].au
• www.rba.com.au
• 0800 722 111
• [e-mail]
• www.rbagroup.co.nz
SYDNEY
MELBOURNE
BRISBANE
PERTH
AUCKLAND
Chronomite Laboratories is a member of Morris Group International
!IMPORTANT
The manufacturer of this water heater will not
be liable for any damages due to the failure
to follow these installation and operation
instructions.
!IMPORTANT
Air in the heater may cause the elements
to burn out. If the water lines are drained,
allowing air into the heater, be sure to follow
the following start-up procedure:
Neutral
“Grd” is earth ground
Active
Conduit connection punching
Strain relief not shown for clarity
See electrical specifications
for correct cable size.
Glands shall be fitted, or
blanks fitted as necessary
and in compliance of
AS3000 supplied by others
Figure 2 Wiring Connection
ALL ELECTRICAL WORKS SHOULD COMPLY WITH THE APPROPRIATE ELECTRICAL CODE
Start up Procedure:
1. Turn off electrical supply - open circuit breaker
2. Turn on water supply.
3. Expel all air from lines and heater.
4. Turn on electrical power supply - close circuit breaker.
INSTALLATION

RBA II - RBAM-240-AU-Series/1112 Page 6/8
Lic. # W22077
Family Of Companies
Made in
the USA
• 1300 788 778
• [email protected].au
• www.rba.com.au
• 0800 722 111
• [e-mail]
• www.rbagroup.co.nz
SYDNEY
MELBOURNE
BRISBANE
PERTH
AUCKLAND
Chronomite Laboratories is a member of Morris Group International
OPERATION:
Turn the hot water fixture on to activate the flow switch. The flow switch activates at 1.5 LPM for 15 & 20 Amp
Models and 2.7LPM for 30 & 40 Amp Models, and deactivates at 1.2 LPM for 15 & 20 Amp Models and 2.3LPM
for 30 & 40 Amp Models. It is not advisable to operate the heaters at 1.5LPM & 2.7LPM (respectively) or below.
If you increase the flow rate of the water, the water temperature will decrease (see Incoming WaterTemperature
Increase table on page 2). Cold water can always be mixed just as with a conventional system if using a mixing tap.
NOTE: Flow rate will vary depending on models used- refer table (page 2)
OPTIONS / FLOW CONTROLS:
The fitted high-quality flow control makes the water heating system operate more effectively, as well as save
water. The supplied 7.6 LPM flow control assures that the flow rate will not exceed 7.6LPM. however,
less water can always be used.
PREVENTIVE MAINTENANCE
To ensure correct operation and to help extend the life of your Chronomite water heater you should perform annual
inspections for damages, loose wiring, leakes, rust, and cleaning of any aerators or strainers. Every
3 years temperature output recordings should be reviewed to ensure performance is as required for your
installation.
!IMPORTANT
Periodically inspect the supply lines, connections and
heater for any moisture, corrosion or other potential
preventable problems.
FLOW CONTROL INSTALLATIONS

RBA II - RBAM-240-AU-Series/1112 Page 7/8
Lic. # W22077
Family Of Companies
Made in
the USA
• 1300 788 778
• [email protected].au
• www.rba.com.au
• 0800 722 111
• [e-mail]
• www.rbagroup.co.nz
SYDNEY
MELBOURNE
BRISBANE
PERTH
AUCKLAND
Chronomite Laboratories is a member of Morris Group International
Your Instant-Flow Micro water heater has no internal user serviceable parts and should be returned to the factory for
repair or replacement. Please contact factory for return authorization. If after following the Installation Instructions,
your Instant-Flow Micro does not heat water in accordance with this literature, please check the following:
1. Low Power - Verify your voltage by using a voltage meter. You should obtain your reading off the two outside
terminals located on the heater. Compare the reading against the voltage specified in the Installation Instructions.
The center terminal is always the earth ground.
2. Low Voltage -The percentage of reduction in voltage will result in a like reduction in temperature increase.
3. Check Low Amperage Draw - Check amperage draw using an Amperage Probe. Please compare your results
with the Installation Instructions (Table 1) to determine if the heater is operating correctly.
4. Length of Pipe - Length of pipe run will affect the temperature increase. The heater should be mounted no more
than 300mm-450mm from the point of use.
5. Check shut off valve - Check shut-off valve and make sure valve is open 100% to allow full water flow rate to
the heater.
6. Check Flow Rate - Controlling flow rate is essential to ensure proper temperature increase. Check your flow rate
to ensure proper operation of the heater.
7. Installation - Heater must be installed in a horizontal position. The silver label will then be located in the upper
left corner as you face the heater.
8. Water Supply - Use cold water only to supply the Instant-Flow Micro cold water inlet.
9. Freezing - Instant-Flow Micro heaters must be drained and stored if installed in a location subject to freezing.
Disconnect both inlet/outlet connections and blow air through the hot water outlet connection of the heater to
assist draining. Failure to completely remove water from the unit will result in freezing and cracking.
10. Problems? - Call our toll-free hotline at RBA Group 1300 788 778.
WARNING!
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• The water resistivity must not be less than 1100 Ohm. cm.
• The appliance must be earthed.
• The appliance is not to be installed in locations where freezing can occur.
• Means of disconnection must be incorporated in the fixed cabling in accordance with wiring rules.
TROUBLE SHOOTING GUIDE

RBA II - RBAM-240-AU-Series/1112 Page 8/8
Lic. # W22077
Family Of Companies
Made in
the USA
• 1300 788 778
• [email protected].au
• www.rba.com.au
• 0800 722 111
• [e-mail]
• www.rbagroup.co.nz
SYDNEY
MELBOURNE
BRISBANE
PERTH
AUCKLAND
Chronomite Laboratories is a member of Morris Group International
SYDNEY MELBOURNE BRISBANE AUCKLAND
PHONE [phone] • FAX [phone]
WEB www.rba.com.au • EMAIL [email protected]u
Your Instant-Flow Micro water heater has been engineered and built to the highest quality stan-
dards and is backed by a full, factory warranty. Every Instant-Flow Micro water heater is guaran-
teed to be free from defects in material and workmanship for a period of (1) year from the date
of purchase. The above warranty applies to original purchaser if unit is installed per Chronomite
Laboratories, Inc.’s Installation Instructions. Chronomite Laboratories, Inc. will repair or exchange
parts at the factory at no cost. This warranty is limited to repairing or replacing said products
which prove to be defective upon factory inspection, return to your nearest rba Group office.
EXCLUSIVE 12-MONTH WARRANTY
WARRANTY POLICY