Chronomite Instant-Flow Micro M-15L/277 User manual

PRODUCT FEATURES
Member of
U.S.Green
Building Council
Water
Conserving
Product
For the model being selected, please place the corresponding
amps and volts values in the Guide Specifications to the right.
APPLICATION: commercial, industrial,
residential, public lavatories, kitchen/bar sink
â
â
â
â
â
â
â
â
â
â
Uses a digital microprocessor for
temperature control
Ultra quick response times for temperature variations -
120 times per second. Microprocessor use is the most
energy efficient means of heating water
Unlimited hot water
Ideal for sensor /hands-free faucets with the
104°F factory preset setting; no mixing valve
needed
Saves water and energy - 99% energy efficient
Meet all CAL GREEN low flow requirements
Vandal resistant rugged cast aluminum housing
Space saving compact size:
6-1/4" (H) x 9-5/8" x 2-3/4"
Meets applicable building codes including
ADA, UL, IAPMO, UPC.
Environmentally friendly
Made in the U.S.A.
®
INSTANT-FLOW MICRO - LOW FLOW
®
Chronomite Instant-Flow Micro - Low Flow models are
manufactured to provide reliable point-of-use hot water. There
is no pressure and temperature relief valve needed (unless
required by code), saving time and money on installation.
Housing is fabricated from
Element assembly is fabricated from Celcon plastic.
Heating coils are nichrome.
Faucet flow controls and compression fittings are supplied
with each unit.
rugged cast aluminum alloy.
®
Instant-Flow Micro - Low Flow
17451 Hurley St. :: City of Industry, CA 91744
Phone [phone] :: 626-937-4270
Fax [phone] :: www.chronomite.com
Complies
with
Standards
for:
Federal
Public Law
111-380
(No Lead)
Made in
the USA
IFM-LF 03/17/15
M-15L / 277 15 277 4150 0.35 35 28 24
M-20L / 120 20 120 2400 0.35 20 - -
M-20L / 208 20 208 4160 0.35 36 28 24
M-20L / 240 20 240 4800 0.35 41 33 27
M-20L / 277 20 277 5540 0.35 47 38 32
M-30L / 120 30 120 3600 0.35 31 25 20
M-30L / 208 30 208 6240 0.35 53 43 36
M-30L / 240 30 240 7200 0.35 61 49 41
M-30L / 277 30 277 8320 0.35 71 57 47
M-40L / 208 40 208 8320 0.35 71 57 47
M-40L / 240 40 240 9600 0.35 82 66 55
M-40L / 277 40 277 11080 0.35 95 76 63
TEMP RISE @
1.00 GPM
TEMP RISE @
1.20 GPM
MODEL AMPS VOLTS WATTS TEMP RISE @
0.80 GPM
ACTIVIATION
GPM
GUIDE SPECIFICATION
M - _____L / ______
x 100 WATTS VOLTS
Tankless Water Heater shall be a Chronomite
Laboratories Model
with Amps and Volts
to heat to a preset temperature of:
104°F 110°F Other temperature
settings available upon
request (specify below)
120°F
Unit shall be provided with Celcon waterways, and
Nichrome heating coils.
Temperature controlled by microprocessor.
OPTIONS
m m m
m
m
m
m
m
PA 765 ABS Housing (P)
Satin Finish Stainless Steel Housing (SS)
High Polish Finish Stainless Steel (SSP)
Pressure & Temp Relief Valve Assembly (TP)
( Meets ADA )
(Meets health code)
OPTIONS
_____
Downloaded from www.GadgetsGo.com, Authorized Chronomite Distributor

TECHNICAL DIMENSIONS
INSTALLATION DIAGRAM
WIRING CONNECTION
"GRD" is
earth
ground.
Conduit
Refer to local
code for wire size
Hot
Hot or
Neutral
ATTENTION:
Unit must be hard wired.
NOTE: Heaters are single phase.
All tests are measured at
the output of the heater.
GENERAL NOTES:
¥
rates, inlet water temperature and pressure to assure the selected
factory preset water temperature.
¥240V models when operated at 220V will have approximately a 15%
wattage decrease.
¥120V models when operated 110V will have approximately a 15%
wattage decrease.
The microprocessor adjusts the heater's power for variations in flow
HOT
COLD
3/8" Hot Water Outlet
Compression
Fittings (2)
Instant-Flow
Micro Heater
J-Box
Mounting Flanges (4)
3/8"
Cold Water
Faucet Feed
5/8" x 3/8" x 3/8"
Three Way Angle
Stop Valve
3/8" Cold Water Inlet
Note: Heater to be
installed below the level
of all hot water outlets
serviced by the heater
1/4"
9-5/8"
5-3/4"
ø 3/16", 4 Mounting Holes
2-3/4"
2"
3-5/16"
ø 1" Access Hole
1-1/8"
2-3/4"
10-1/8"
1-1/8"
1-5/16"
HOT
COLD
6-1/4"
1/4"
Front Service Panel
Chronomite Laboratories, Inc.
City of Industry, CA 91744 U.S.A.
SELECTION SUMMARY
& APPROVAL FOR
MANUFACTURING
Model Number & Options_____________________________________________________________________Quantity_______________
Company_______________________________________________________________________________________________________
Contact_________________________________________________Title____________________________________________________
Signature
(Approval for
Manufacturing)__________________________________________________________________Date ____________________________
PH. 800-447-4962
626-937-4270
FAX [phone]
www.chronomite.com
®
INSTANT-FLOW MICRO - LOW FLOW
¥
104°F factory preset setting temperature ; no mixing valve needed
¥Factory setting of 110°F or above require cold water mixing at the
hand wash faucet.
¥Microprocessor limits temperature increase according to the pre-
selected temperature.
Instant-Flow Micro is ideal for sensor/hands-free faucets with the
IFM-LF 03/17/15
®
INSTANT-FLOW MICRO - LOW FLOW
Dimensions: 6-1/4" (H) x 9-5/8" x 2-3/4"
Weight: 5 lbs.
Materials: Rugged cast aluminum housing
Celcon plastic element assembly
with nichrome coils
Housing Color: White
Minimum Operating Flow Rate: 0.35 GPM
Minimum Operating Pressure: 25 PSI
Maximum Operating Pressure 150 PSI
Maximum Operating Temperature: 140°F
Listing: UL, IAPMO, UPC, ADA
Rear Electrical Knock-Out
Chronomite Laboratories assumes no responsibility for use of void or suspended data. © Copyright Chronomite Laboratories, Inc.
Member of Morris Group International, City of Industry, CA Please visit www.chronomite.com for most current specifications.
Downloaded from www.GadgetsGo.com, Authorized Chronomite Distributor