Ciro TWIN RAIL User manual

TWIN RAIL HIGHWAY PEG MOUNTS WITH EXTENSION ARM
1 Right Twin Rail Footrest
1 Le Twin Rail Footrest
1 Clamp Clevis Mount Right Assembly
1 Clamp Clevis Mount Le Assembly
WARNING:
This indicaon alerts you to the fact
that ignoring the contents described
herein can result in potenal serious
injury or death if not followed.
CAUTION:
This indicaon alerts you to the fact
that ignoring the contents described
herein can or will result in material
damage and/or personal injury.
ATTENTION:
This indicaon alerts you to the fact
if you ignore this detail you will affect
the performance or funconality of
the product.
All Ciro products are designed for
"easy assembly" and/or "plug and
play". We recommend a competent
mechanic install our products, using
standard mechanical procedures to
assure a safe and successful
installaon.
INSTALLATION INSTRUCTIONS:
1. Park on a level surface and shut off the motorcycle. Ensure that the engine has had me to cool before installaon.
2. Prepare the clamp and engine guard surface by using soap and hot water to remove any dirt followed by an ammonia
based glass cleaner to remove any wax or oil.
3. Remove the 1/2” hex bolt from the clamp assembly. Separate the clamp halves and place them around the engine guard.
The serrated face of the clamp should be facing outward and away from the motorcycle.
NOTE: The Clevis and extension arm can be assembled in mulple posions. Experiment to find a
posion that suits the rider. (FIG.1.)
4. In its approximate final locaon, reinstall the hex bolt and thread it into the extension arm unl finger ght. Adjust the
assembly to the desired posion.
CAUTION: Ciro recommends a thread locking fluid such as 3M Scotch-Weld TL-43 for this installaon.
G0160505 REV. -
NOTE:
Ciro® warrants that products sold
hereunder to the original purchaser,
if maintained and operated under
normal condions, shall be free from
any defects in materials and
workmanship for a period of (3)
years from date of purchase, and a
lifeme warranty against LED failure.
Ciro will have no obligaon if the
customer cannot show proof of
purchase.
Warranty will not be granted unless
the part is properly installed and
maintained.
Ciro will not be liable for any
consequenal and incidental
damages, including labor, or non-Ciro
products.
Please visit our website Ciro3d.com
for our complete warranty policy.
parts included
FIG.1Typical right side assembly
for an average height rider.
Typical right side assembly
for an taller height rider.

G0160505 REV. -
PAGE 2
5. Install the Twin Rail Footrests and adjust the angle to your liking.
NOTE: Adjust the angle of the extension arm to affect the height of the footrest. (A.)
Adjust the angle of the clevis aached to the extension arm to affect how the footrest folds. (B.)
Adjust the angle of the footrest on the footrest adapter to find a comfortable posion. (D.)
6. Check and securely ghten all fasteners.
CAUTION: Ciro recommends a thread locking fluid such as 3M Scotch-Weld TL-43 for this installaon.
(A.) 1/2” hex bolt holding the clamp and extension arm should be ghtened to 40-45 .-lb. torque.
(B.) 3/8” socket head screw aaching the clevis to the extension arm should be ghtened to 12-16 .-lb. torque.
(C.) 3/8” socket head screw in the clevis should be ghtened to 12-16 .-lb. torque.
(D.) 5/16” socket head screw in the footrest should be ghtened to 10-13 .-lb. torque.
FIG.2
CLICK TAB SPRING
MALE CLAMP HALF
FEMALE CLAMP HALF
Serrated face
CLEVIS
FOOTREST ADAPTER
TWIN RAIL FOOTREST
HEX BOLT
1/2”-13 x 1 3/8”
FLAT WASHER
1/2”
SOCKET HEAD SCREW
3/8”-16 x 1 3/8”
BUTTON HEAD SCREW
4-40 x .375
“D” SPRING
NARROW WASHER
5/16” SOCKET HEAD SCREW
5/16”-18 x 1”
(A.)
(B.)
(D.)
SOCKET HEAD SCREW
3/8”-16 x 1”
(C.)
EXTENSION ARM
HIGH COLLAR LOCK WASHER
5/16”