Cirrus CR800 series User manual

INSTALLATION AND USER MANUAL
For software version 1.0.0

LiveNoise —Introduction
The LiveNoise software connects to a Cirrus CR800 series or CR260
series Sound Level Meter and displays the sound level in real-time.
Direct or Network Connection
The connection between the computer and the sound level meter can be
either direct (RS232 cable) or over a Network. For greater flexibility and
longer distances the network option is the best, offering either a wired or
wireless solution. If a network is already available on the premises then no
extra cabling should be necessary as long as a wireless router or hub is
close to the sound level meter.
Warnings and Alarms
LiveNoise can indicate when preset levels have been exceeded. The
Warning level is used to indicate to the user that the level is getting high.
When the noise exceeds the Alarm level for the preset period of time, the
alarm is indicated on-screen until the user clicks the Clear Alarms button.
Alarms can be stored to a data file and loaded into a spreadsheet or word
processor.

Software Installation
Insert the LiveNoise CD and follow the on-
screen instructions.
If the installation does not start automatically then run the
setup.exe application on the CD.
System Setup—Direct Serial Connection
The LiveNoise software can connect to the sound level meter using the
computer’s RS232 (COM) port.
Typical RS232 Connection
Connect the sound level meter to the computer’s
COM port using the cable supplied —the 9-way
female connector goes to the computer’s port.
The sound level meter can be powered by
batteries or by an optional power supply unit.
Configure the Software
Select the Tools | Preferences menu option
and click on the Communications tab.
Select the RS232 option and the COM port
that the meter is connected to.

System Setup—Network Connection
The LiveNoise software can connect to the sound level meter over an
Ethernet or Wireless network.
Connecting Up —Typical Wireless Network with Router
Wireless
Router
Serial Server
Connect the Sound Level Meter to the SE5001 Serial Server using the
RS232 cable. Connect the Serial Server to your Wireless Router (or other
access hub) using the network cable.
Then connect the power from
the adapter to the Serial Server
(green connector) and from
there to the Sound Level Meter.
Plug the adapter in and switch
the Sound Level Meter on.
Topower
adapter
The RUN light should flash and the LAN light
should be on, indicating that the Serial Server is
connected to the network.

Configure the Software —Network Connection
Select the Tools | Preferences menu option and click on the
Communications tab.
Select the TCP/IP option then click the Serial Server button to configure
the settings for the SE5001 Serial Server settings.
The Monitor software should detect the Serial Server on your network.
Click on the IP address (1) and then on the Config button (2).
Select an IP Address, Gatewayand Subnet Mask to suit your network. If
unsure, contact your network supervisor. If these are not correct for your
particular network then the LiveNoise software will not connect to the
sound level meter.
Press the Config Nowbutton to set the new configuration then close the
Monitor program.
Back in the LiveNoise program, enter the
same IP address. In this example the Serial
Server is configured to 192.168.2.10.
The port number should usually be left at
4660.

LiveNoise Options
Select the Tools | Preferences menu option or click the button.
Options
Automatically Connect at Startup instructs the program to connect to the
sound level meter as soon as it starts up.
Keep LiveNoise Window On Top keeps the LiveNoise program on top of
other programs so that you can see the sound levels at all times.
Graph
X Axis Period sets the time period you can see on the graph.
Y Axis —Follow meter’s range sets the graph’s Y axis to show the same
range that the meter is set to.
Y Axis —Automatic. The graph’s Y axis will auto-scale.
Auto-Range the Sound Level Meter. If the noise goes outside the
instrument’s range then it instruct the meter to adjust its range accordingly.
Alarms
Enable Alarms. Use this to switch the alarm option on or off.
Warn. When the noise reaches this sound level the software will show a
visible warning.
Alarm. When the noise reaches this level for at least the number of
seconds chosen then an “Alarm” is generated. The alarm is indicated on-
screen and optionally saved to a file.
Files
Path. This is the location that the Alarms file will be saved to.
Save Alarms to File. If selected, alarms will be save to a text file.

Connecting to the Sound Level Meter
To connect LiveNoise to the sound level meter, select the Tools | Connect
to Meter menu option, or click the green run button.
Once connected, the software
will show a graph of the sound
levels, along with the warning
and alarm levels (if the alarms
option is enabled).
Click on the sound level
button (top-right) to
switch the display to a
large number.
Connection Problems
If the software cannot connect to the meter it will report one of the follow-
ing errors:
Could not open RS232 port COMx. Check that you have set the correct
COM port for the software to connect to the sound level meter. This error
occurs if the software cannot find the selected COM port on the computer.
Could not find the remote TCP/IP server. The software could not find the
SE5001 Serial Server on the network. Check that the server is configured
to an IP address and subnet mask that suit the network. Check also that
the LiveNoise software has the same IP address set.
Connection opened but the sound level meter is not responding. The soft-
ware has managed to open the RS 232 port, or connect through to the Se-
rial Server on a network, but the meter does not respond. Check that the
meter has power, is switched on and is correctly connected to the com-
puter or to the Serial Server, depending on your configuration.

Warnings and Alarms
The LiveNoise software has a Warning level and an Alarm level that can
be configured to suit your application.
The software indicates the warning level on the graph. When the warning
level is exceeded the digital level reading changes colour and the status
bar shows the message “WARNING LEVEL”. No other action is taken on a
warning and nothing additional is stored.
When the level exceeds the alarm level the digital level reading changes
colour and the status bar shows the message “HIGH LEVEL”. If the level
stays above the warning level for the preset time (see LiveNoise Options)
then an Alarm is generated.
Alarms
Alarms are indicated on the right-hand side of
the LiveNoise display, showing the start time
(the time at which the level first crossed the
threshold) and the maximum sound level
(LAFmax).
Click on any of the alarms to get more infor-
mation, including the date and the alarm duration, which
indicates the amount of time that the level remained above
the threshold.
Alarms Saved to File
If LiveNoise is configured to save alarms to file (see LiveNoise Options
section) then a Comma Separate Variable (CSV) file is created for each
day that the software runs. By default, these files will be created in My
Documents / LiveNoise, although this can be changed if necessary.
The file names are of the format: ALM-yyyy-mm-dd.CSV, where yyyy is
the year, mm is the month and dd is the day.
These files can be loaded straight into a text editor as well as directly into
most spreadsheets and word processors.

Contacting NoiseMeters
UK
Tel: [phone]
Fax: [phone]
Email:[email protected]
Web: www.noisemeters.co.uk
USA
Tel: [phone]
Fax: [phone]
Email:[email protected]
Web: www.noisemeters.com
International
Tel: [phone]
Fax: [phone]
Email:[email protected]
Web: www.noisemeters.com