CIS VISION:elite VCC-F60U29GE Quick start guide

VCC-F60U29GE Rev.900-682-30-00
©2008 CIS Corporation. All rights reserved.
1
En
g
lish
2M Pixel Color
(RAW&RGB) Gig-E Camera
VCC-F60U29GE
Product Specification
& Operational Manual
CIS Corporation

VCC-F60U29GE Rev.900-682-30-00
©2008 CIS Corporation. All rights reserved.
2
Table of Contents
1. Scope of Application.......................................................................................................................... 3
2. Handling Precautions ........................................................................................................................ 3
3. Product Outline................................................................................................................................. 4
4. Specification..................................................................................................................................... 5
4.1. General Specification .................................................................................................................. 5
4.2. Camera Output Signal Specification.............................................................................................. 7
4.3. CCD Spectral Response (Representative Value)............................................................................. 8
4.4. Image output Format (Coyote Application Setting) .......................................................................... 8
5. Function Settings.............................................................................................................................. 9
6. External Connector Pin Assignment...................................................................................................11
6.1. 12 pins Circular Connector HR10-10R-12PA (HIROSE) ..................................................................11
6.2. RJ-45 Gigabit Ethernet Connector MOD-YSJ88DA03C-CN+ (HONDA TSUSHIN KOGYO CO., LTD) .....12
7. Timing Chart....................................................................................................................................13
7.1. Horizontal Synchronous Signals Timing........................................................................................13
7.2. Full Frame Scan Mode Timing.....................................................................................................13
7.3. Standard Trigger Mode Timing....................................................................................................14
7.4. Pulse Width Trigger Timing.........................................................................................................15
8. Partial Scan Mode Details .................................................................................................................16
9. Remote Interface Function ...............................................................................................................17
10. Initial Settings ...............................................................................................................................18
11. CCD Optical Axis Accuracy..............................................................................................................19
12. Dimensions....................................................................................................................................20
13. Cases for Indemnity (Limited Warranty)...........................................................................................22
14. CCD Pixel Defect............................................................................................................................23
15. Product Support.............................................................................................................................23

VCC-F60U29GE Rev.900-682-30-00
©2008 CIS Corporation. All rights reserved.
3
1. Scope of Application
This is to describe VCC-F60U29GE, 2M pixels Gig-E Color CCD Camera. All specifications contained herein
are subject to change without prior notice. Reproduction in whole or in part is prohibited.
2. Handling Precautions
The camera must not be used for any nuclear equipments or aerospace equipments with which mechanical
failure or malfunction could result in serious bodily injury or loss of human life. Our warranty does not apply
to damages or defects caused by irregular and/or abnormal use of the product.
Please observe all warnings and cautions stated below.
Our warranty does not apply to damages or malfunctions caused by neglecting these precautions.
zDo not use or store the camera in the following extreme conditions:
¾Extremely dusty or humid places.
¾Extremely hot or cold places (operating temperature –5 to℃+40 )℃
¾Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.
¾Places subject to fluorescent light reflections.
¾Places subject to unstable (flickering, etc.) lighting conditions.
¾Places subject to strong vibration.
zDo not apply excessive force or static electricity that could damage the camera.
zDo not shoot direct images that are extremely bright (e.g., light source, sun, etc.), and when camera
is not in use, put the lens cap on.
zFollow the instructions in Chapter 6, “External connector pin assignment” for connecting the camera.
Improper connection may cause damages not only to the camera but also to the connected devices.
zConfirm the mutual ground potential carefully and then connect the camera to monitors or computers.
AC leaks from the connected devices may cause damages or destroy the camera.
zDo not apply excessive voltage.(Use only the specified voltage.) Unstable or improper power supply
voltage may cause damages or malfunction of the camera.
zThe voltage ripple of camera power DC +12V±10% shall be within ±50mV. Improper power
supply voltage may cause noises on the video signals.

VCC-F60U29GE Rev.900-682-30-00
©2008 CIS Corporation. All rights reserved.
4
zThe rising time of camera power supply voltage shall be less than +10V, Max 60ms. Please
avoide noises like chattering when rising.
10 4020 30 50
10
11
12
[V]
Voltage Rising Time [ms]
9
8
7
60 70
Power Supply Voltage
In case of abnormal operation, contact the distributor from whom you purchased the product.
3. Product Outline
VCC-F60U29GE is a Gigabit Ethernet interfaced, high-resolution industrial color video camera module utilizing
a 1/1.8 inch PS IT CCD. 2M pixels CCD image sensor with on-chip micro-lenses realizes high sensitivity and
high resolution. At RAW mode setting, entire pixels can be read out within approx. 1/27s. At RGB mode
setting, entire pixels can be read out within approx. 1/13s.
Features
□ High speed communication, maximum 108MB/s. (Comform to 1000BASE-T)
□ The maximum transmission distance is approx. 100m with cable more than CAT5e.
□ Camera settings can be set via LAN.
□ Software trigger input via LAN or hardware trigger input via 12pin connector at rear is selectable.
□ Shutter speed can be set from 1/27sec ～1/45,000sec by 1H at RAW mode,
and 1/13sec ～1/22,000sec by 1H at RGB mode.
□ At partial scan mode, both capturing start position and capturing width can be set by 3H.
Bundled Items
□ Camera
□ iPORT Software Development Kit 2.4.1 build 921. ※
□ Gig-E Camera Control Software (CamCtlSetup.exe) ※
□ Start up manual
※Please ask for the details or download it from our web.

VCC-F60U29GE Rev.900-682-30-00
©2008 CIS Corporation. All rights reserved.
5
4. Specification
4.1. General Specification
Item Specification
Pickup device Device Type 1/1.8” Interline Transfer color CCD, Sony ICX274AQ
Effective Pixel Number 1628 (H) x 1236 (V)
Unit Cell Size 4.40μm (H) x 4.40μm (V)
Chip Size 8.50mm (H) x 6.80mm (V)
Videooutput frequency Pixel Clock RAW Mode: 64 MHz
RGB Mode: 32 MHz
Horizontal Frequency RAW Mode: 33.333 kHz Pixel Clock: 1920CLK
RGB Mode: 16.667 kHz
Vertical Frequency Full Frame Scan Mode: Scanning lines: 1252H
RAWMode:26.624Hz
RGBMode:13.312Hz
Sync. system Internal Sync. System
Video output standard Gigabit Ethernet (Comform to 1000BASE-T) Trasferring speed: 108MB/s (max)
Resolution 1000 TV lines (Coyote Application Bayer Viewer: RGB Convert)
Resolving power RAW Mode: 8bit / 10bit or RGB Mode: 24 bit is selectable
Sensitivity RAW Mode: F5.6 2000 lx (Shutter speed 1/27s(OFF), Gain 0dB)
RGB Mode: F8.0 2000lx (Shutter speed 1/13s(OFF), Gain 0dB)
Minimum illumination RAW Mode: F1.4 20lx (Shutter speed 1/27s(OFF), Gain +12dB)
RGB Mode: F1.4 10lx (Shutter speed 1/13s(OFF), Gain +12dB)
Dust or stains in
optical system
No dust or stain shall be detected on the testing screen with setting the camera
aperture at F16.
Power requirements DC +12V ±10% (Max voltage not to exceed +15V)
Power consumption RAW Mode: 5.5W
RGB Mode: 5.0W
(At DC +12V IN, normal mode, and full frame scan or partial scan mode)
Dimension Refer to overall dimension drawing (Clause 12)
55mm x 55mm x 60mm (excluding projection)
Mass Approx. 190 g
Lens mount C mount (Refer to overall dimension drawing)
Optical axis accuracy Refer to drawing for CCD Optical Axis Accuracy (Clause 11)
Gain variable range 0～+12dB
White balance
adjustment range
2800K～9000K

VCC-F60U29GE Rev.900-682-30-00
©2008 CIS Corporation. All rights reserved.
6
Item Specification
Shutter speed
Variable range
RAW Mode: 1/27s(OFF) ～1/45000s
RGB Mode: 1/13s(OFF) ～1/22000s
Trigger shutter mode ・Standard Trigger Mode ・Pulse Width Trigger Mode
Safety/Quality
standards
UL: Conform to UL Standard including materials and others.
RoHS: Conform to RoHS
CE: EN55022:2006 (Class A) for Emission
EN61000-6-2:2005 for Immunity
FCC: To be applied to FCC Class A digital Device
This device complies with Part 15 of the FCC Rules. Operation is subject to the
followin
g
two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, includin
g
interference that
may cause undesired operation.
Durability
Vibration
Acceleration 98 m/s2(10.0G)
Frequency 20～200 Hz
Direction XYZ 3 directions
Testing time 120 min for each direction
Shock No mulfunction shall be occurred with 490m/s2(50G) for ±X, ±
Y, and ±Z, 6 directions. (without package)
Operation environment
Temperature Performance guaranteed temperature: 0℃～+40℃
Camera operation guaranteed temeprature: -5℃～+40℃
※All the specifications specified in this manual is
g
uaranteed
under performance guaranteed temperature.
※All the camera functions operate normally under operation
guaranteed temperature
Humidity RH 20～80% with no condensation
Storage environment Temperature -25℃～+60℃
Humidity RH 20～80% with no condensation
Recommended System
LAN Card Intel PRO/1000 series
LAN Cable MOD-YSP-A1AS-SP series (Honda Tsushin Kogyo)
MV series (CEI)
OS Windows 2000 and over
Memory Over 512 MB (over 1GB recommeded)

VCC-F60U29GE Rev.900-682-30-00
©2008 CIS Corporation. All rights reserved.
7
4.2. Camera Output Signal Specification
Item Specification
Video output
data Video out 1624(H) x 1224 (V) At Full Frame Scan Mode
60MHz 2Tap output
Sync. Signal
I/O
LVAL output LVTTL (3.3V Output) HR10-10R-12PA
FVAL output LVTTL (3.3V Output) ※Output pin assi
g
nment is
set via iPort SDK. Please
refer to our VCC-G60/F60
GE series startup manual,
section 5.6. Trigger Mode.
DVAL output LVTTL (3.3V Output)
SP (Exposure Pulse) LVTTL (3.3V Output)
Trigger input
Polarity POSI/NEGA Selectable
Trigger Pulse width Min. over 2 HD ～Max. under 2504 HD
Hardware Trigger input LVTTL (5.0V Tolerant) HR10-10R-12PA
SoftwareTriggerinput RJ-45
Video output
signal
White Clip Level Digital 8bit : FFh
Setup Level Digital 8bit : 08h
Dark Shading Digital 8bit : Under 08h for both horizontal and vertical
(Conditions: Gain 0dB)
※ 5 secounds shall be waited after turning on power to get proper camera operation.
180ΩTTL In(a)
VCC
+3.3V
TTL Out(b)
※(a):0～3
(b):0～2
180Ω
220KΩ
6.6V
6.6V
UDZS TE-17 6.2B
(ROHM)
SN74LV125A(TI)
Vih : Vcc × 0.7(Min)
Vil : Vcc × 0.3(Max)
Voh : 2.48V(Min)
Vol : 0.44V(Max)
12 pins circular connector at rear GPIO interface

VCC-F60U29GE Rev.900-682-30-00
©2008 CIS Corporation. All rights reserved.
8
4.3. CCD Spectral Response (Representative Value)
※Lens charcteristics and luminous source charcteristics are not considered.
4.4. Image output Format (Coyote Application Setting)
(1) RAW Mode
・ 1-Tap, Bayer RGB
・ Area of interest Width : 1624 Height : 1224 Offset X : 0 Offset Y : 19
・ Bayer Pattern GBRG
・
R
G
G
B
(2) RGB Mode
・RGB Color, 24bit, Packed
・ Area of interest Width : 1624 Height : 1224 Offset X : 0 Offset Y : 19

VCC-F60U29GE Rev.900-682-30-00
©2008 CIS Corporation. All rights reserved.
9
5. Function Settings
Camera functions can be set with serial communications.
Function Address Data
Gain 001
0: 0 dB: Analog Fixed Gain
1: +3 dB: Analog Fixed Gain
2: +6 dB: Analog Fixed Gain
3: +12 dB: Analog Gain (+6dB) + Digital Gain (+6dB)
4: Manual Gain (Refer to Address 005 and 006)
E-Shutter 002
RAW Mode (Address 018:002) RGB Mode (Address 018:003)
0: 1/27s(Off) 1/13s(Off)
1: 1/27s 1/27s
2: 1/60s 1/60s
3: 1/90s 1/90s
4: 1/120s 1/120s
5: 1/150s 1/150s
6: 1/200s 1/200s
7: 1/250s 1/250s
8: 1/500s 1/500s
9: 1/750s 1/750s
10: 1/1000s 1/1000s
11: 1/2000s 1/2000s
12: 1/5000s 1/5000s
13: 1/10000s 1/10000s
14: 1/15000s 1/15000s
15: 1/45000s 1/22000s
16: Manual Shutter (Refer to Address 009 and 010)
White Balance 003
0: THRU
1: 3200K
2: Spare
3: Spare
4: Manual White Balance (Address 156, 157, 158 and 159)
Trigger Mode 004 0: Normal Mode (Trigger Mode Off) 1: Standard Trigger Mode (Shutter speed can be set with address 002.)
2: Pulse Width Trigger Mode (Shutter speed can be set with trigger pulse width.)
Manual Analog Gain 005&006 0～512: 0: 0dB 512: over +10dB (Log Linear)
※2LSB is invalid with 10bit data. Set the address 001 data to 004.
Manual Shutter Control 009&010 0～1251:
RAW Mode: 1/13s (Off)～1/45000s
RGB Mode: 1/27s (Off)～1/22000s
※Set the address 002 data to 016.
Address 009 MSB and address 010 LSB makes total 16 bit.
RAW Mode: Shutter speed = (1251-(009&010)) x 30.00μs + 20.84μs
RGB Mode: Shutter speed = (1251-(009&010)) x 60.00μs + 41.69μs
Max data = 1251
Trigger Polarity 011 0: Positive Input
1: Negative Input

VCC-F60U29GE Rev.900-682-30-00
©2008 CIS Corporation. All rights reserved.
10
Function Address Data
Output Data Select 013 0: 8bit Output Data
1: 10bit Output Data
Gamma Mode 014 0: Gamma Off (1.0)
1: Gamma On (Option)
Partial Scan Mode 015 0: Full Frame Scan Mode
1: Partial Scan Mode
Partial Scan Start Position 016&017 0～407:
Set the address 015 data to 001.
Address 016 MSB and address 017 LSB makes total 16 bit.
Start Position: 3 H/step Min Data: 0 (0H)/Max Data : 407 (1221 H)
Start Position (016&017)+ Effective Line (019&020) <= 407
Camera Mode 018 2: RAW Mode
3: RGB(24bit) Mode
Partial Scan Effective Line 019&020 0～407:
Set the address 015 data to 001.
Address 019 MSB and address 020 LSB makes total 16 bit.
Effective Line: 3 H /step Min Data: 0 (3 H)/Max Data : 407 (1224 H)
Start Position (016&017)+ Effective Line (019&020) <= 407
Partial Scan Total Line 021&022 0～1251: Read Only
Total line number at Partial Scan Mode or Full Frame Scan Mode minus 1 is set
Manual White Balance R
(Right) 156&157 256 ～ 1023: 256: x1(0dB)～1023: x4(+12dB)
※Set address 003 data to 004.
Manual White Balance B
(Right) 158&159 256 ～ 1023: 256: x1(0dB)～1023: x4(+12dB)
※Set address 003 data to 004.
Data Save 255 Input 083 or 053 to save the data in EEP-ROM.
Note: When setting the data with 2 Byte, High Byte shall be set first, then Low Byte to the next.
The camera rewrites the internal resister when receiving Low Byte.

VCC-F60U29GE Rev.900-682-30-00
6. External Connector Pin Assignmental Connector Pin Assignment
6.1. 12 pins Circular Connector HR10-10R-12PA (HIROSE)6.1. 12 pins Circular Connector HR10-10R-12PA (HIROSE)
Pin
No. Signals which can be controlled by GigE Camera Control Software
1 GND
2 Power In DC +12V
3 TTL In3
(LVTTL Input 5V Tolerant) Trigger Input
4 TTL Out2
(LVTTL 3.3V Output) LVAL, FVAL, DVAL ,SP(Exposure) Output
5 GND
6 TTL In2
(LVTTL input 5V Tolerant) Trigger Input
7 TTL Out1
(LVTTL 3.3V Output) LVAL, FVAL, DVAL ,SP(Exposure) Output
8 TTL In1
(LVTTL input 5V Tolerant) Trigger Input
9 TTL Out0
(LVTTL 3.3V Output) LVAL, FVAL, DVAL ,SP(Exposure) Output
10 TTL In0
(LVTTL Input 5V Tolerant) Trigger Input
11 NC
12 NC
TTL In(a) a:0～3・・・Trigger Input etc.TTL In(a) a:0～3・・・Trigger Input etc.
TTL Out(b) b:0～2・・・LVAL, FVAL, DVAL, SP, Pulse Generator etc.TTL Out(b) b:0～2・・・LVAL, FVAL, DVAL, SP, Pulse Generator etc.
※ Pin assignment and functions can be set arbitrarily via iPORT software.※ Pin assignment and functions can be set arbitrarily via iPORT software.
Please refer to iPORT.Software.Coyote.pdf in￥Program Files￥Pleora Technologies Inc￥iPORT
Software￥Documentation.
Please refer to iPORT.Software.Coyote.pdf in￥Program Files￥Pleora Technologies Inc￥iPORT
Software￥Documentation.
©2008 CIS Corporation. All rights reserved.
11

VCC-F60U29GE Rev.900-682-30-00
©2008 CIS Corporation. All rights reserved.
12
6.2. RJ-45 Gigabit Ethernet Connector MOD-YSJ88DA03C-CN+ (HONDA TSUSHIN KOGYO CO., LTD)
LINK(Green LED) ACT(Yellow LED)
LINK LED: Lighting-off ・・・Unconnected to LAN
Lighting-on ・・・Connected to LAN
Blinking ・・・Transmitting the data
ACT LED: Lighting-off ・・・Unconnected or connected with 10Mbps/100Mbps
Lighting-on ・・・Connected with 1000Mbps

VCC-F60U29GE Rev.900-682-30-00
©2008 CIS Corporation. All rights reserved.
13
7. Timing Chart
7.1. Horizontal Synchronous Signals Timing
LVAL Output
296CLK
Video Output
DVAL Output
296CLK
FVAL Output
1920CLK
1624CLK
CLK
RAW Mode = 64MHz
RGB Mode = 32MHz
1 CLK
7.2. Full Frame Scan Mode Timing
LVAL Output
Video Output
DVAL Output
FVAL Output
1234567891012491248 11 12 28 30 31
(CCD Read Out Signal)
9H
28H 1224H
19H
Total = 1252H
125212511250
1224H
29

VCC-F60U29GE Rev.900-682-30-00
©2008 CIS Corporation. All rights reserved.
14
7.3. Standard Trigger Mode Timing
□Trigger operation is CLK sync, V-Sync Reset.
Delay time, from detecting the trigger edge to starting exposure, is 1.08μs at RAW mode and 2.16μs at
RGB mode.
□Trigger input can be accepted even when the camera is outputting video signals. However, a shutter
timing, to start the next video output before completion of transferring video output for the prior signals,
can not be worked. To input trigger signals when the camera is outputting video signals for the prior
signals, it shall be synchronized with the down edge of camera LVAL output.
□Trigger input during the execution of exposure (exposure time) shall be ignored. (Refer to the “G” below.)
LVAL Output
Video Output
FVAL Output
DVAL Output
19H
TTL INx
(CCD Read
Out Signal)
19
29 1252
1224H
1243H
(Trigger Input)
Exposure Time
TTL INx
(Trigger Input)
(Sub Pulse)
(CCD Read Out Signal)
Delay(Fixed)
SP Output
(Exposure Signal)
a
b
3
CLK 66 CLK
a
b
RAW Mode(CLK 64MHz)
1.08μs
a
b
RGB Mode(CLK 32MHz)
2.16μs
nHD×30μs + 20.84μs
nHD×60μs + 41.69μs

VCC-F60U29GE Rev.900-682-30-00
©2008 CIS Corporation. All rights reserved.
15
7.4. Pulse Width Trigger Timing
□Trigger operation is CLK sync, V-Sync Reset.
Delay time, from detecting the trigger edge to starting exposure, is 1.08μs at RAW mode, and 2.16μs at
RGB mode. Delay time, from detecting the trigger edge to completion of exposure, is 21.92μs at RAW
mode, and 43.84μs at RGB mode.
□Trigger input can be accepted even when the camera is outputting video signals. However, a shutter
timing, to start the next video output before completion of transferring video output for the prior signals,
can not be worked. Please refer to the “C” below. To input trigger signals when the camera is
outputting video signals for the prior signals, it shall be synchronized with the down edge of camera LVAL
LVAL Output
Video Output
FVAL Output
DVAL Output
19H
TTL INx
(CCD Read
Out Signal)
Exposure Time
19
29 1252
1224H
1243H
(Trigger Input)
TTL INx
(Trigger Input)
(Sub Pulse)
(CCD Read Out Signal)
Delay(Fixed)
SP Output
(Exposure Signal)
a
b
3
CLK 66 CLK
953
CLK
a
b
450
CLK
RAW Mode(CLK 64MHz)
1.08μs
21.92μs
a
b
RGB Mode(CLK 32MHz)
2.16μs
43.84μs
Delay(Fixed)
output.

VCC-F60U29GE Rev.900-682-30-00
©2008 CIS Corporation. All rights reserved.
16
8. Partial Scan Mode Details
Capturing start position and capturing width can be set by 3H via LAN.
LVAL Output
(Normal Scan) 9 H
Video Output
(Normal Scan)
1252 H
VIDEO Output
(Partial Scan)
LVAL Output
(Partial Scan) 9 H
19 H
Total Line(Address 021&022) + 1H
1224 H
Y Offset
19H + Starting Position
(Address016&017)
Effective Line
(Address 019&020)×3+3H
High Speed
Transmit Term High Speed Transmit Term
Reading out position register (Address 016 & 017): 0(0H) ~ 407 (1221H) 3H/step
Effective line register (Address 019 & 020): 0(3H) ~ 407 (1224H) 3H/step
Total line register (Address 021 & 022): 435H + (Effective line register × 2) + 2 (Read Only)
Note: Reading out position and effective line shall meet the following condition.
Reading out position register + Effective line register = < 407
Otherwise, the value, 407 – reading out position register, will be set to the effective line register.
<Example 1> Conditions: Reading out position register (Address 016 & 017) = 000
Effective line register
(Address 019&020)
Effective Lines Total Line register
+ 1H
Frame Rate
RAW mode RGB mode
0 3 H 438 H 76 fps 38 fps
・・・・・
159 480 H 756 H 44 fps・22 fps・
・・・・・
255 768 H 948 H 35 fps 18 fps
・・・・・
341 1026 H 1120 H 30 fps 15 fps
・・・・・
407 1224 1252 H 27 fps 13 fps

VCC-F60U29GE Rev.900-682-30-00
©2008 CIS Corporation. All rights reserved.
17
9. Remote Interface Function
Through LAN, the camera can be controlled.
(1) The settings for RS-232C
Baud rate : 9600bps
Data : 8bit
Stop bit : 1bit
Parity : None
XOn/XOff : Not controlled
(2) Control code
・ The total control code is 14 bits, which conforms to ASCII code.
・ The control code consists of camera No. process code, remote controller address, remote
controller data, and CR. Execute Read/Write through PC, and the camera will reply the data.
1 2 3 4 5 6 7th Byte 8 9 10 11 12 13 14
Camera No. Process code Remote controller
address
Remote controller data CR
000000: fixed “R” Read mode Please refer to the
address table of
Section 5. Function
Settings.
000～255 0 Dh
“W” Write mode
“C” Camera mode
Camera No. is fixed with 6 bite numerical strings, “000000”.
Process code
Input any one of R, W, or C to the process code.
R (read mode) is to read the data of remote controller address.
Please be noted to set any dummy data (000～255) to 11th ～13th, since a command shall
consists of 14 bytes.
W (write mode) is to write the data to the remote controller address.
Please be noted that the data cannot be saved into EEPROM of the camera.
(Reboot the camera, and the data is reset to the initial setting.)
To save the data into EEPROM, please refer to Section 5. Function Settings.
C is the code to send the data back from the camera.
Note: Do not set code C when sending the data from PC side.

VCC-F60U29GE Rev.900-682-30-00
©2008 CIS Corporation. All rights reserved.
18
Remote controller address
Note: Do not write the data into the address other than specified, since it may cause
the damages or malfunction of the camera.
Remote controller data
Set the decimal number (000～255) for the remote controller data. Please be noted to set any
dummy data at read control mode.
CR
Be sure to input “CR” to confirm the end of the command.
※Note: When setting the data with 2 Byte, High Byte shall be set first, then Low Byte to the next.
The camera rewrites the internal resister when receiving Low Byte.
10. Initial Settings
Function Address Data
Gain 001 0: 0dB
E-Shutter 002 0: 1/13s (Off)
White Balance 003 1: 3200K
Trigger Mode 004 0: Normal Mode (Trigger Mode Off)
Trigger Polarity 011 0: Positive Input
Output Data Select 013 0: 8 bit Output Data
Partial Scan Mode 015 0: Full Frame Scan Mode
Camera Mode 018 1: RGB (24bit) Mode
Partial Scan Total Lines 021 & 022 1251: Read Only

VCC-F60U29GE Rev.900-682-30-00
©2008 CIS Corporation. All rights reserved.
19
Datum Plane B
55
55
Inclination of optical
Axis to datum plane B
Inclination of optical
Axis to datum plane A
Datum Plane A
6.3
6011.1
Datum Plane A
910-003-00-00
*)Dimension from datum plane A to the center of lens mount.
The center of effective pixels
shall be within φ0.6 to the center of
the lens mount.
Inclination of effective pixels θ
To datum plane A shall be
θ≦±0.5°
(Unit :mm)
90°±0.2°
Under ±0.5°
θ±0.5°
27.5
±0.3
(＊)
11. CCD Optical Axis Accuracy

VCC-F60U29GE Rev.900-682-30-00
12. Dimensions
©2008 CIS Corporation. All rights reserved.
20
28±0.1
28±0.1
55
55
Under R1
60 6.3 11.1
Product Name
Label Position
35±0.1
4.5±0.1 52
GigE DC IN
ACT
LINK
999-500-00-00(1/2)
*2) Screw length from C mount lens surface shall be under 6mm. And protruding portion shall be
lesss than 10mm.
*1) C Mount screws comply with ANSI/ASME B1.1, 1-32UN(2B).
(Unit:mm)
F29
0
-0.05
4-M3
Depth 4
4-M3
Depth 4
CMount(*)
2 MEGA PIXEL