CIS VCC-5CXP3R Quick start guide

VCC-5CXP3R Rev. 905-0052-00
©2017 CIS Corporation. All rights reserved.
CoaXPress I/F
5.3M CMOS Color (RAW) Camera
VCC-5CXP3R
Product Specifications
& Operational Manual
CIS Corporation
English
Aegis Electronic Group, Inc.

VCC-5CXP3R Rev. 905-0052-00
©2016 CIS Corporation. All rights reserved.
1
Table of Contents
1Handling Precautions .........................................................................................................................3
2Product Outline .................................................................................................................................3
3Bundled Items...................................................................................................................................3
3.1 Standard Bundled Items..............................................................................................................3
3.2 Packaging ..................................................................................................................................3
4Specifications ....................................................................................................................................4
4.1 General Specifications .................................................................................................................4
4.2 Camera In/Output Signal Specifications........................................................................................5
4.3 Spectral Response ......................................................................................................................5
5External Connector Pin Assignment.....................................................................................................6
5.1 75ΩBNC Connector .....................................................................................................................6
5.2 6 pins Circular Connector ............................................................................................................6
3 pins SIGNAL_OUT Circuit ....................................................................................................................6
5 pins TRIGGER_IN Circuit .....................................................................................................................7
6How to Save and Initialize the Setting.................................................................................................7
7Camera Operation Mode ....................................................................................................................8
7.1 Link Configuration.......................................................................................................................8
7.2 Pixel Format Settings........................................................................................................................8
7.3 Camera Sync Mode.....................................................................................................................8
7.3.1 Internal Sync Mode (Free Run Mode) ...........................................................................................9
7.3.2 External Trigger Sync Mode .........................................................................................................9
8Function Settings............................................................................................................................. 13
8.1 Gain Settings............................................................................................................................ 13
8.2 Exposure Time Settings............................................................................................................. 14
8.3 ROI (Region Of Interest)........................................................................................................... 15
8.4 Sub-Sampling ........................................................................................................................... 16
8.5 Defective Pixel Correction.......................................................................................................... 17
8.6 Shading Correction ................................................................................................................... 17
8.7 Black Offset.............................................................................................................................. 17
8.8 Test Pattern Indication .............................................................................................................. 17
8.9 Indicator LED Lighting Control................................................................................................... 18
8.10 Camera Timing Output.............................................................................................................. 19
8.11 DeviceUserID Settings .............................................................................................................. 19
8.12 White Balance .......................................................................................................................... 19
9Sequence Control Function............................................................................................................... 20
9.1 Basic Operation ........................................................................................................................ 21
9.2 Outline for Trigger Mode and Burst Mode Operation.................................................................... 21
9.3 Trigger Mode ............................................................................................................................ 22
9.4 Burst Mode .............................................................................................................................. 23
9.5 Index Mode.............................................................................................................................. 24
9.6 Setting Items for Sequence Control ........................................................................................... 25
9.7 Sequence Information Output ................................................................................................... 26
11 Dimensions ..................................................................................................................................... 29
11.1 Optical Axis Accuracy ................................................................................................................ 29
11.2 Camera Dimension.................................................................................................................... 30
Aegis Electronic Group, Inc.

VCC-5CXP3R Rev. 905-0052-00
©2016 CIS Corporation. All rights reserved.
2
12 Case for Indemnity (Limited Warranty) ............................................................................................. 31
・Product Support...................................................................................................................................... 31
Aegis Electronic Group, Inc.

VCC-5CXP3R Rev. 905-0052-00
©2016 CIS Corporation. All rights reserved.
3
1Handling Precautions
The camera module must not be used for any nuclear equipments or aerospace equipments with which
mechanical failure or malfunction could result in serious bodily injury or loss of human life. Our warranty
does not apply to damages or defects caused by irregular and/or abnormal use of the product.
All specifications contained herein are subject to change without prior notice. Reproduction in whole or in
part is prohibited.
Please observe all warnings and cautions stated below.
Our warranty does not apply to damages or malfunctions caused by neglecting these precautions.
Do not use or store the camera module in the dusty or humid places.
Do not apply excessive force, vibration, or static electricity that could damage the camera. Handle the camera
with caution.
Do not shoot direct images that are extremely bright (e.g., light source, sun, etc). When extremely strong light
source is shot, smear or blooming may occur. When the camera is not in use, please put the protection cap on.
Follow the instructions in Chapter 5, “External Connector Pin Assignment” for connecting the camera module.
Improper connection may cause damages not only to the camera module but also to the connected devices.
Confirm the mutual ground potential carefully and then connect the camera module to monitors or
computers. AC leaks from the connected devices may cause damages or destroy the camera module.
Do not apply excessive voltage. (Use only the specified voltage.) Unstable or improper power supply
voltage may cause damages or malfunction of the camera assembly.
Do not disassemble the camera. The camera once disassembled shall be out of warranty.
2Product Outline
VCC-5CXP3R is a CoaXPress interfaced small Color camera utilizing a 1 type, 5.3M pixels CMOS image sensor.
Features
□29mm x 29mm x 55mm in size
□Global shutter CMOS (Color)
□CoaXPress CXP-1/2/3/5/6 x1 each
□The maximum cable length: Approx. 100m (at CXP-1)
□ROI
□Sub-sampling
□Exposure, Gain settings
□External trigger mode (Fixed trigger shutter mode / Pulse width trigger shutter mode)
□Sequence control
□Shading Correction
□GenICam complied
3Bundled Items
3.1 Standard Bundled Items
□Camera module, VCC-5CXP3R
□Lens cap
3.2 Packaging
□Individual carton
□Master carton (10 pcs/carton)
Note) Q’ty per master carton may vary depends on the shipping q’ty.
Aegis Electronic Group, Inc.

VCC-5CXP3R Rev. 905-0052-00
©2016 CIS Corporation. All rights reserved.
4
4Specifications
4.1 General Specifications
(1) Image Sensor
Device Type
1 type Global shutter CMOS
Effective Pixel Numbers
2592(H) × 2048(V)
Unit Cell Size
4.8μm(H) × 4.8μm(V)
(2) Video Output Frequency
Pixel Clock
72MHz
(3) CoaXPress
Ver, 1.0complied. CXP1/2/3/5/6 x1 each
(4) Video Output Format
BayerRG8 / BayerRG10
(5) Resolution
2048 TV lines
(6) Output
Sensor AD
10bit
(7) Sensitivity
F2.8 2000 lx (Shutter 1/300(s), Gain 0dB)
(8) Minimum Illumination
F1.4 65lx (Shutter 1/300(s), Gain 18dB)
(9) Pixel Defect Correction
Corrected at Ex-factory
(10) Gain Variable Range
x1～x32 (0dB～30dB)
(11) Shutter
Global Shutter
(12) Shutter Speed Variable
Range
Preset : 1/10000, 1/5000, 1/2500, 1/1200, 1/600, 1/300, 1/150, 1/100
Manual : 100[us]～Approx. 1/Framerate[us]
(13) Gamma Correction
1 fixed
(14) Trigger Mode
Free run mode (Camera internal trigger)
Trigger mode
・Preset shutter trigger
・Pulse width shutter trigger
(15) Partial Scan (ROI)
8 Preset patterns ※Including Full-resolution (ROI OFF)
(16) Power Requirements
PoCXP
(17) Power Consumption
3.6W (CXP-6) [at full pixel and free run]
(18) Dimensions
H:29mm W:29mm D:55mm ※without protruding portion
(19) Weight
Approx. 75 g
(20) Lens Mount
C Mount
(21) Safety/Quality standards
UL: Conform to UL Standard including materials and others.
(22) Durability
CE:
EMC:
2014/30/EU
CE:
FCC:
EN61000-6-4:2007+A1:2011 for Emission
EN61000-6-2:2005 for Immunity
RoHS:
2011/65/EU EN50581 (RoHS2)
Vibration
No malfunction shall be occurred with 90m/s2(50G) for ±X,±Y, and
±Z, 6 directions. (Without packaging).
(23) Operation Environment
Performance
guaranteed
0 ～+40℃
Humidity
20 ~ 80%RH
with no condensation
Operation
guaranteed
-5 ～+45℃
Humidity
20 ~ 80%RH
with no condensation
※Performance guaranteed: All the specifications specified in this manual is guaranteed
under performance guaranteed temperature.
※Operation guaranteed: All the camera functions operate normally under operation
guaranteed temperature.
(24) Storage Environment
Storage Temperature: -25 ~ +60℃, Humidity: 20 ~ 80%RH with no condensation.
Aegis Electronic Group, Inc.

VCC-5CXP3R Rev. 905-0052-00
©2016 CIS Corporation. All rights reserved.
5
4.2 Camera In/Output Signal Specifications
(1)Video Output Data
Max. Effective Video Output
2592(H) × 2048(V)
(2)Image Signal Output
BNC Connector LINK 0
PoCXP
Power, Video, and Superimposed
Control signals
(3)Video Output Format
Tap Geometry
1X-1Y
(4)Video Signals Output Level
White Clip Level
FFh
At 8bit
Setup Level
CXP-1 :01 -1/+2
CXP-2/3 :01 ±01h
At 8bit and 0dB
※Setup level shall be fractured at gain up. It can be adjusted by BlackOffset.
(4)External Trigger Signal
Input
CoaXPress BNC Connector
Low speed uplink
20.83Mbps
6 pins round connector Pin No.5
TTL input
DC5.0V (Max. 5.5V)
(5)General Signal Output
6 pins round connector Pin No.3
EXPOSURE,
FVAL, LVAL,
Uplink Trigger (After decode)
With register settings,
1 can be output.
5V output
4.3 Spectral Response
※The lens characteristic and the illuminant characteristics are excluded.
※Please refer to RED, GREEN, and BLUE in the graph below.
Aegis Electronic Group, Inc.

VCC-5CXP3R Rev. 905-0052-00
©2016 CIS Corporation. All rights reserved.
6
5External Connector Pin Assignment
5.1 75ΩBNC Connector
(BCJ-BPLHA CANARE)
5.2 6 pins Circular Connector
(SNH-8-6(RPCB) SamWoo Electronics)
Pin No.
Signals
Note
1
NC
2
NC
3
SIGNAL_OUT
The output of the selected signal
4
NC
5
TRIGGER_IN
Trigger input
6
GND
Conducted with camera casing
※NC means Non-Connection. Do not connect anything to the terminal.
3 pins SIGNAL_OUT Circuit
Timing signals inside the camera can be output. Output signal can be set by LineSource at Digital IO Control.
Please refer to the 8. Function Settings for the details.
・5.0V CMOS logic level output
・Output voltage Low: 0.55Vdc (Max), High: 3.8Vdc (Min)
1
2
3 4
5
6
PoCXP (Signal/Power+24V)
GND
Aegis Electronic Group, Inc.

VCC-5CXP3R Rev. 905-0052-00
©2016 CIS Corporation. All rights reserved.
7
5 pins TRIGGER_IN Circuit
Trigger signals can be input directly into the camera. When to use this terminal, set TriggerSource of AcquisitionControl to
LineIn. Please refer to 7. Camera Operation Mode for the details.
・5.0V, 3.3V CMOS level input (TTL compatible)
・Input voltage Low: 0.5Vdc(Min), High: 2.1Vdc(Max)
6How to Save and Initialize the Setting
UserSets
UserSetSave
(Execute)
UserSetDefault
(Execute)
If you wish to initialize the setting values, execute UserSetDefault. Execution is only valid at Link rate (CxpLinkConfiguration)
CXP-1. However, as long as you do not execute UserSetSave, the setting values will not be saved. If you wish to save the
setting values, execute UserSetSave. Setting values will be saved to the memory in the camera and will operate with the saved
settings at next start-up.
+5.0V
HD74LV1GT32ACME
1
2
3 4
5
SIGNAL_OUT
(CAMERA_INTERNAL)
HD74LV1GT14ACME
1
2
3
5
4
100
1K
+5.0V
(CAMERA_INTERNAL) TRRIGER_IN
Aegis Electronic Group, Inc.

VCC-5CXP3R Rev. 905-0052-00
©2016 CIS Corporation. All rights reserved.
8
7Camera Operation Mode
7.1 Link Configuration
7.2 Pixel Format Settings
ImageFormatControl
PixelFormat
BayerRG8
BayerRG10
7.3 Camera Sync Mode
TriggerSelectorAndActivation
AquisitionMode
：Internal Sync Mode (Free Run Mode)
FrameStartRisingEdge
：External Trigger Sync Mode (Fixed Trigger Shutter Mode: Rising Edge)
FrameStartFallingEdge
：External Trigger Sync Mode (Fixed Trigger Shutter Mode: Falling Edge)
FrameStartLevelHigh
：External Trigger Sync Mode (Pulse Width Trigger Shutter Mode: High Active)
FrameStartLevelLow
：External Trigger Sync Mode (Pulse Width Trigger Shutter Mode: Low Active)
FrameBurstStart
：Internal Sync Mode (Burst Mode of Sequence function)
・TriggerSource
To set the method for trigger input at External Trigger Sync Mode.
LinkTrigger0 : Utilize LOW SPEED uplink of CoaXPress, and input trigger from frame grabber via coaxical cable.
LinkIn : Input trigger from No.5 pin of circular connector at camera rear.
・TriggerSoftware
This command generates trigger in the camera, and captures 1 frame. Please note that this trigger does not have the time
accuracy like the trigger generated by TriggerSource.
Only valid Acquisition Control mode is TriggerSelectorAndActivation --- FrameStartRisingEdge Mode
Transfer Control
CxpLinkConfiguration
CXP1_ X1
CXP2_ X1
CXP3_ X1
CXP5_ X1
CXP6_ X1
Acquisition Control
TriggerSelectorAndActivation
AquisitionMode
FrameStartRisingEdge
FrameStartFallingEdge
FrameStartLevelHigh
FrameStartLevelLow
FrameBurstStart
TriggerSource
LinkTrigger0
Line0
TriggerSoftware
(Execute)
Aegis Electronic Group, Inc.

VCC-5CXP3R Rev. 905-0052-00
©2016 CIS Corporation. All rights reserved.
9
7.3.1 Internal Sync Mode (Free Run Mode)
This is a mode to use triggers continuously made in the camera. No external trigger shall be used.
・Please set TriggerSelectorAndActvation to AcquisitionMode.
Configuration
Frame rate (fps)
8bit
10bit
CXP-1
21.3
16.3
CXP-2
42.6
34.8
CXP-3
42.6
42.6
CXP-5
85.1
69.5
CXP-6
85.1
85.1
7.3.2 External Trigger Sync Mode
This is a mode to input external trigger signals to capture images by any preferred timings.
Some delay shall be considered from when camera recognized the trigger edge to when actual exposure starts.
Please refer to the delay time as below.
Input
Delay Time
LinkTrigger0
Approx. 3.4us
Line0
Approx. 150us
・Notes for trigger pulse input timing
A trigger pulse can be input during Readout. However, please do not input a trigger pulse while reading out signals for the prior
frame since it ends its exposure. (In other words, please avoid inputting a trigger pulse while reading out signals for the prior
frame and starts reading out signals for the next frame.)
Video output from the camera might not be executed when the trigger is input again at the prohibited timing, or right after
FVAL turns to “L”at the timing of the end of exposure. If the camera stops operating, or cannot output image data without
malfunctions, please execute “SensorReset”command after quitting trigger input to start the operation again.
※If the camera does not start its operation, please execute the restoration of power.
Device Control
SensorReset
(Execute)
Trigger
Exposure
FVAL
(≒Readout)
Aegis Electronic Group, Inc.