Cisco T3 Quick start guide

CHAPTER
20-1
Cisco Network Modules Hardware Installation Guide
OL-2485-20
20
Connecting T3/E3 Network Modules
This chapter describes how to connect T3/E3 network modules for modular access routers and contains
the following sections:
•1-Port T3/E3 Network Modules, page 20-1
•Connecting T3/E3 Network Modules to the Network, page 20-2
•T3/E3 Network Module LEDs, page 20-3
•Related Documents, page 20-3
Tip To determine whether your router supports a specific network module, see Table 1-6 on page 1-16.
1-Port T3/E3 Network Modules
The NM-1T3/E3 network module is a single-port universal T3/E3 network module with integrated
CSU/DSU, clear channel, and subrate support. (See Figure 20-1.) Channels on the network module can
be configured as either T3 or E3 through Cisco IOS software.
Figure 20-1 1-Port T3/E3 Network Module Faceplate
Note The NM-1T3/E3 network module provides subrate T3 support for Digital Link, Kentrox, Larscom,
Verilink, and Adtran. The NM-1T3/E3 network module also provides subrate E3 support for Digital Link
and Kentrox.
SEE MANUAL BEFORE INSTALLING NETWORK MODULE
72536
NM-1T3/E3
LP AIS AL
CD
TX RX
FERF/RAI
T3/E3
EN

20-2
Cisco Network Modules Hardware Installation Guide OL-2485-20
Chapter 20 Connecting T3/E3 Network Modules
Connecting T3/E3 Network Modules to the Network
Connecting T3/E3 Network Modules to the Network
To connect a T3/E3 network module to the network, use a 75-ohm 728-A coaxial cable to connect the
BNC connector on the network module to a networking device. (See Figure 20-2.)
Warning This equipment contains a ring signal generator (ringer), which is a source of hazardous voltage. Do
not touch the RJ-11 (phone) port wires (conductors), the conductors of a cable connected to the RJ-11
port, or the associated circuit-board when the ringer is active. The ringer is activated by an incoming
call. Statement 1042
Warning If the symbol of suitability with an overlaid cross appears above a port, you must not connect the port
to a public network that follows the European Union standards. Connecting the port to this type of
public network can cause severe injury or damage your router. Statement 1031
Caution To minimize transient surges, the internal wiring should not be routed in the same conduit with power
lines or external telephone lines.
Figure 20-2 Connecting a T3/E3 Network Module to a Networking Device (Cisco 7603 Router Shown)
72715
SUPERVISOR2
WS-X6K-SUP2-2GE
STATUS
SYSTEM
CONSOLE
PWR MGMT
RESET
CONSOLE
CONSOLE
PORT
MODE PCMCIA EJECT
PORT 1 PORT 2
Switch Load
100%
1%
LINK
LINK
OSM-4OC12 POS-SI
4 PORT OC-12 POS SM IR
STATUS 1
1
2
2
3
3
4
4RESET
LINK
LINK
LINK
LINK
CARRIER
ALARM
CARRIER
ALARM
CARRIER
ALARM
CARRIER
ALARM
ACTIVE
TX
RX
TX
PORT 1
RX
ACTIVE
TX
RX
TX
PORT 2
RX
ACTIVE
TX
RX
TX
PORT 3
RX
ACTIVE
TX
RX
TX
PORT4
RX
OSM-4OC12 POS-SI
4 PORT OC-12 POS SM IR
STATUS 1
1
2
2
3
3
4
4RESET
LINK
LINK
LINK
LINK
CARRIER
ALARM
CARRIER
ALARM
CARRIER
ALARM
CARRIER
ALARM
ACTIVE
TX
RX
TX
PORT 1
RX
ACTIVE
TX
RX
TX
PORT 2
RX
ACTIVE
TX
RX
TX
PORT 3
RX
ACTIVE
TX
RX
TX
PORT4
RX
SEE MANUAL BEFORE INSTALLING NETWORK MODULE
NM-1T3/E3
LP AIS AL
CD
TX RX
FERF/RAI
T3/E3
EN
TX
RX
TX RX

20-3
Cisco Network Modules Hardware Installation Guide
OL-2485-20
Chapter 20 Connecting T3/E3 Network Modules T3/E3 Network Module LEDs
Tip When connecting the T3/E3 network module to a port adapter used in another router series, verify that
you are connecting the TX port on the network module with the RX port on the port adapter, and the TX
port on the port adapter to the RX port on the network module.
T3/E3 Network Module LEDs
All network modules have an enable (EN) LED. This LED indicates that the module has passed its
self-tests and is available to the router. See Figure 20-3 and Table 20-1 for LEDs on the T3/E3 network
module.
Figure 20-3 T3/E3 LEDs
Related Documents
For additional information, see the following documents.
Tip For information on obtaining documentation, see the “Obtaining Documentation” section on page viii.
For information on obtaining technical assistance, see the “Obtaining Technical Assistance” section on
page xi.
Table 20-1 T3/E3 Network Module LEDs
LED Meaning
CD Green indicates that a signal is present on the port.
LP Yellow indicates that a loopback condition is present on the port.
AIS Yellow indicates an alarm on the DS3 transmission.
FERF/RAI Yellow indicates a remote failure at the far end of the connection.
AL Yellow indicates that the port is out of frame.
EN Green indicates that the network module has passed self-test and is available to
the router.
SEE MANUAL BEFORE INSTALLING NETWORK MODULE
72537
NM-1T3/E3
LP AIS AL
CD
TX RX
FERF/RAI
T3/E3
EN
CD
LED
LP
LED
FERF/RAI
LED
AIS
LED
EN
LED
AL
LED

20-4
Cisco Network Modules Hardware Installation Guide OL-2485-20
Chapter 20 Connecting T3/E3 Network Modules
Related Documents
Cisco IOS Software Documentation
For information on Cisco IOS software features specific to the T3/E3 network module, see the Clear
Channel T3/E3 Network Module with Integrated CSU/DSU document.