Cisco WS-SVC-ASA-SM1-K7 Installation and operation manual

Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Cisco Catalyst 6500 Series ASA Services Module
Installation Note
Revised: July 15, 2011
This installation note provides the hardware installation instructions for the Cisco ASA Services
Module.
Contents
This document contains these sections:
•Safety, page 2
•Overview, page 8
•Required Tools, page 9
•Installing the ASA Services Module, page 9
•Removing the ASA Services Module, page 17
•Preventing Electrostatic Discharge Damage, page 18
•Translated Safety Warnings, page 21
•Obtaining Documentation and Submitting a Service Request, page 29
Product Numbers:
WS-SVC-ASA-SM1-K7
WS-SVC-ASA-SM1-K8
WS-SVC-ASA-SM1-K9

2
Cisco Catalyst 6500 Series ASA Services Module Installation Note
OL-23955-01
Safety
Safety
Safety warnings appear throughout this publication in procedures that may harm you if performed
incorrectly. A warning symbol precedes each warning statement. The warnings below are general
warnings that are applicable to the entire publication.
Statement 1071—Warning Definition
Warning IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this
device.
Statement 1071
SAVE THESE INSTRUCTIONS
Waarschuwing
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan
veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij
elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard
praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de
waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt
raadplegen.
BEWAAR DEZE INSTRUCTIES
Varoitus
TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin
käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu
onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen
mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien
lausuntonumeroiden avulla.
SÄILYTÄ NÄMÄ OHJEET
Attention
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant
entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez
conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures
couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des
avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS

3
Cisco Catalyst 6500 Series ASA Services Module Installation Note
OL-23955-01
Safety
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen
kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und
den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder
Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
Avvertenza
IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle
persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli
relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.
Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le
traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
Advarsel
VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du
begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med
elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten
av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne
enheten.
TA VARE PÅ DISSE INSTRUKSJONENE
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de
lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos
perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de
prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para
localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
GUARDE ESTAS INSTRUÇÕES
¡Advertencia!
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular
cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los
procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el
número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña
a este dispositivo.
GUARDE ESTAS INSTRUCCIONES

4
Cisco Catalyst 6500 Series ASA Services Module Installation Note
OL-23955-01
Safety
Varning!
VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.
Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och
känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av
varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna
anordning.
SPARA DESSA ANVISNINGAR

5
Cisco Catalyst 6500 Series ASA Services Module Installation Note
OL-23955-01
Safety
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões
corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os
circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o
número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de
segurança traduzidos que acompanham o dispositivo.
GUARDE ESTAS INSTRUÇÕES
Advarsel
VIGTIGE SIKKERHEDSANVISNINGER
Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for
legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de
involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til
undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de
oversatte advarsler, der fulgte med denne enhed.
GEM DISSE ANVISNINGER

6
Cisco Catalyst 6500 Series ASA Services Module Installation Note
OL-23955-01
Safety

7
Cisco Catalyst 6500 Series ASA Services Module Installation Note
OL-23955-01
Safety
Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly
touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94

8
Cisco Catalyst 6500 Series ASA Services Module Installation Note
OL-23955-01
Overview
Overview
The ASA Services Module, see Figure 1, is the next generation 10Gbps+ Security Services blade for the
Catalyst 6500 series switch. The ASA Services Module is supported in any slot in the Catalyst 6500
E-series chassis. The ASA Services Module is not supported in non-E-series chassis. The ASA Services
Module requires either a Supervisor Engine 720-3B, Supervisor Engine 720-3BXL, or Supervisor
Engine 720-10GE (either a VS-S720-10G-3C or a VS-S720-10G-3CXL) to operate.
Figure 1 ASA Services Module Faceplate
LEDs
The ASA Services module has two LEDs visible on the module front panel. Table 1 lists the LEDs and
their function.
1STATUS LED 3RESET switch
2ID LED
255279
WS-SVC-ASA-SM1
ASA SERVICE MODULE
SHUTDOWN
STATUS
ID
2
1 3
Table 1 ASA Services Module LEDs
LED Color and Meaning
STATUS Green—Both ASA Services module processors have
finished booting up, all diagnostics pass, and the module is
operational
Yellow—ROMMON is running; the ASA Services module
has not finished booting up
Red—The module is powering up or the ASA Services
Module has a fault.
ID The ID LED functions as a service indicator. The blue LED
is turned on and off by the system administrator from the
switch console to aid the service personnel in identifying
which ASA Services Module within a chassis needs
attention. When turned on, the LED flashes on and off at
500 msec intervals.

9
Cisco Catalyst 6500 Series ASA Services Module Installation Note
OL-23955-01
Required Tools
SHUTDOWN Switch
The ASA Services Module has a recessed switch, labeled SHUTDOWN, mounted on the module front
panel. If a fault is detected on the ASA Services Module, the operator must press the SHUTDOWN
switch to interrupt the Services module processors and initiate an orderly shutdown of the storage
devices on the module before the module is removed from the chassis.
Required Tools
These tools are required to install the ASA Services Module in the chassis:
•Small flat-blade screwdriver
•No. 2 Phillips screwdriver
•Antistatic mat or foam pad to support the module
•Your own ESD-prevention equipment or the disposable grounding wrist strap included with the
module
•Switching-module filler plates (Cisco part number SLOTBLANK-09 or WS-X6K-SLOT-CVR-E).
Replaces blank slot covers in slots that are directly adjacent to the Services Module slot (either
above and below on horizontal slot chassis or left and right on vertical slot chassis).
Chassis Unused Slots Restrictions
If you are installing one or more of the Cisco Services Modules in your chassis that are listed in Table 2,
the slots directly adjacent to the services module (above and below or to the left and to the right) must
contain either line cards or switching-module filler plates (Cisco part numbers WS-X6K-SLOT-CVR-E
or SLOTBLANK-09). If either adjacent slot is unused and currently has a blank slot cover (Cisco part
number WS-X6K-SLOT-CVR) installed, you must remove the blank slot cover and replace it with a
switching-module filler plate for NEBS compliance.
Installing the ASA Services Module
Note For NEBS compliance when installing Cisco Services Modules, refer to “Chassis Unused Slots
Restrictions” section on page 9.
Caution To prevent ESD damage, handle the module by the metal carrier edges only.
Table 2 Service Modules Requiring Switching-Module Filler Plates
WS-SVC-NAM3-6G-K9(=) WS-SVC-ASA-SM1-K7(=)
WS-SVC-ASA-SM1-K8(=) WS-SVC-ASA-SM1-K9(=)

10
Cisco Catalyst 6500 Series ASA Services Module Installation Note
OL-23955-01
Installing the ASA Services Module
To install the ASA Services Module in the chassis, follow these steps:
Step 1 Verify that an ESD grounding strap is attached to your wrist and to proper ground.
If you are unsure about the correct way to attach an ESD grounding strap, see the “Preventing
Electrostatic Discharge Damage” section on page 18 for instructions.
Step 2 Verify that the two slots adjacent to the slot where you are installing the services module have either a
module installed in them or a switching-module filler plate installed (Cisco part numbers
SLOTBLANK-09 or WS-X6K-SLOT-CVR-E) if either slot is unused. If either slot has a blank slot cover
(Cisco part number WS-X6K-SLOT-CVR), you need to remove the blank slot cover and replace it with
a switching-module filler plate for NEBS compliance.
Step 3 Verify that the captive installation screws are tightened on all of the modules installed in the chassis.
This step assures that the EMI gaskets on all of the installed modules are fully compressed in order to
maximize the opening space for the services module.
Note If the captive installation screws are loose, the electromagnetic interference (EMI) gaskets on
the installed modules expand and push the modules toward the open slot, which reduces the
opening size and makes it difficult to reinstall the module.
Step 4 If you are installing the ASA Services Module in an empty slot, remove the module filler plate that
covers the selected chassis slot by removing the two Phillips pan-head screws from the filler plate. Save
the module filler plate and the two screws for future use.
Note If you must remove an existing module, see the “Removing the ASA Services Module” section
on page 17. The procedure is applicable to services modules and other types of modules.
Step 5 Remove the new ASA Services Module from its shipping packaging and from the antistatic shipping bag.
Caution To prevent ESD damage, handle the module by the metal carrier edges only. Place the unpackaged
services module on an antistatic surface.
Step 6 Fully open both ejector levers on the ASA Services Module. (See Figure 2.)