Cisco 8540 - Catalyst Campus Switch Router Modular Expansion... User manual

Installing the Controller
This chapter describes how to install the controller.
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work
on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard
practices for preventing accidents. Use the statement number provided at the end of each warning to locate
its translation in the translated safety warnings that accompanied this device.
Statement 1071
Warning
SAVE THESE INSTRUCTIONS
•Unpacking and Inspecting the Controller, on page 1
•Preparing for Controller Installation, on page 2
•Installing the Controller In a Rack, on page 5
•Initial Controller Setup , on page 9
•System BIOS and Cisco IMC Firmware, on page 9
Unpacking and Inspecting the Controller
When handling internal controller components, wear an ESD strap and handle modules by the carrier edges
only.
Caution
Keep the shipping container in case the controller requires shipping in the future.
Tip
The chassis is thoroughly inspected before shipment. If any damage occurred during transportation or any
items are missing, contact your customer service representative immediately.
Note
Installing the Controller
1

Step 1 Remove the controller from its container and save all packaging material.
Step 2 Compare the shipment to the equipment list provided by your customer service representative. Verify that you have all
items.
Step 3 Check for damage and report any discrepancies or damage to your customer service representative. Have the following
information ready:
• Invoice number of shipper (see the packing slip)
• Model and serial number of the damaged unit
• Description of damage
• Effect of damage on the installation
Preparing for Controller Installation
This section provides information about preparing for controller installation.
Installation Guidelines
Read the installation instructions before using, installing or connecting the system to the power source.
Statement 1004
Warning
This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the
protective device is rated not greater than: 20A. Statement 1005
Warning
The plug-socket combination must be accessible at all times, because it serves as the main disconnecting
device. Statement 1019
Warning
A readily accessible two-poled disconnect device must be incorporated in the fixed wiring. This is applicable
to systems with DC power supply only. Statement 1022
Warning
This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence
of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician
if you are uncertain that suitable grounding is available. Statement 1024
Warning
Installing the Controller
2
Installing the Controller
Preparing for Controller Installation

This unit might have more than one power supply connection. All connections must be removed to de-energize
the unit. Statement 1028
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement
1030
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations. Statement
1040
Warning
To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommended
ambient temperature of: 40° C (104° F). Statement 1047
Warning
Invisible Laser Radiation. Do not expose users of telescopic optics. Class 1/1M Laser Products. Statement
1055
Warning
Invisible laser radiation may be emitted from the end of the unterminated fiber cable or connector. Do not
view directly with optical instruments. Viewing the laser output with certain optical instruments (for example,
eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard. Statement
1056
Warning
Installing the Controller
3
Installing the Controller
Installation Guidelines

Installation of the equipment must comply with local and national electrical codes. Statement 1074
Warning
Pluggable optical modules comply with IEC 60825-1 Ed. 3 and 21 CFR 1040.10 and 1040.11 with or without
exception for conformance with IEC 60825-1 Ed. 3 as described in Laser Notice No. 56, dated May 8, 2019.
Statement 1255
Warning
To ensure proper airflow it is necessary to rack the controllers using rail kits. Physically placing the units on
top of one another or “stacking” without the use of the rail kits blocks the air vents on top of the controllers,
which could result in overheating, higher fan speeds, and higher power consumption. We recommend that
you mount your controllers on rail kits when you are installing them into the rack because these rails provide
the minimal spacing required between the controllers. No additional spacing between the controllers is required
when you mount the units using rail kits.
Caution
Avoid UPS types that use ferroresonant technology. These UPS types can become unstable with systems such
as the Cisco UCS, which can have substantial current draw fluctuations from fluctuating data traffic patterns.
Caution
Rack Requirements
This section provides the requirements for the standard open racks.
The rack must be of the following type:
• A standard 19-in. (48.3-cm) wide, four-post EIA rack, with mounting posts that conform to English
universal hole spacing, per section 1 of ANSI/EIA-310-D-1992.
•The rack post holes can be square 0.38-inch (9.6 mm), round 0.28-inch (7.1 mm), #12-24 UNC, or #10-32
UNC when you use the supplied slide rails.
• The minimum vertical rack space per controller must be two RUs, equal to 3.5 in. (88.9 mm).
Equipment Requirements
The slide rails supplied by Cisco Systems for this controller do not require tools for installation if you install
them in a rack that has square 0.38-inch (9.6 mm), round 0.28-inch (7.1 mm), or #12-24 UNC threaded holes.
Slide Rail Adjustment Range
The slide rails for this controller have an adjustment range of 26 to 36 inches (660 to 914 mm).
Installing the Controller
4
Installing the Controller
Rack Requirements

Installing the Controller In a Rack
Installing the Slide Rails
This section describes how to install the controller in a rack using the rack kits that are sold by Cisco.
To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to
ensure that the system remains stable. The following guidelines are provided to ensure your safety:
This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest
component at the bottom of the rack.
If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in
the rack.
Statement 1006
Warning
Step 1 Attach the inner rails to the sides of the controller:
a) Align an inner rail with one side of the controller so that the three keyed slots in the rail align with the three pegs on
the side of the controller.
b) Set the keyed slots over the pegs, and then slide the rail toward the front to lock it in place on the pegs. The front slot
has a metal clip that locks over the front peg.
c) Install the second inner rail to the opposite side of the controller.
Figure 1: Attaching Inner Rail to Side of Controller
Locking clip on inner rail2Front of controller1
Step 2 Open the front securing plate on both slide-rail assemblies. The front end of the slide-rail assembly has a spring-loaded
securing plate that must be open before you can insert the mounting pegs into the rack-post holes.
On the outside of the assembly, push the green arrow button toward the rear to open the securing plate.
Installing the Controller
5
Installing the Controller
Installing the Controller In a Rack

Figure 2: Front Securing Mechanism, Inside of Front End
Securing plate shown pulled back to
open position
3Front mounting pegs1
Rack post2
Step 3 Install the slide rails into the rack:
a) Align one slide-rail assembly front end with the front rack-post holes that you want to use.
The slide rail front-end wraps around the outside of the rack post and the mounting pegs enter the rack-post holes
from the outside-front (see Figure 2: Front Securing Mechanism, Inside of Front End, on page 6).
The rack post must be between the mounting pegs and the open securing plate.
Note
b) Push the mounting pegs into the rack-post holes from the outside-front.
c) Press the securing plate release button, marked “PUSH.” The spring-loaded securing plate closes to lock the pegs in
place.
d) Adjust the slide-rail length, and then push the rear mounting pegs into the corresponding rear rack-post holes. The
slide rail must be level front-to-rear.
The rear mounting pegs enter the rear rack-post holes from the inside of the rack post.
e) Attach the second slide-rail assembly to the opposite side of the rack. Ensure that the two slide-rail assemblies are at
the same height with each other and are level front-to-back.
f) Pull the inner slide rails on each assembly out toward the rack front until they hit the internal stops and lock in place.
Step 4 Insert the controller into the slide rails:
This controller can weigh up to 44 pounds (approximately 20 kilograms) when fully loaded with components.
We recommend that you use a minimum of two people or a mechanical lift when lifting the controller. Attempting
this procedure alone could result in personal injury or equipment damage.
Caution
a) Align the rear of the inner rails that are attached to the controller sides with the front ends of the empty slide rails on
the rack.
b) Push the inner rails into the slide rails on the rack until they stop at the internal stops.
c) Slide the release clip toward the rear on both inner rails (Figure 3: Inner Rail Release Clip, on page 7), and then
continue pushing the controller into the rack until its front slam latches engage with the rack posts.
Installing the Controller
6
Installing the Controller
Installing the Slide Rails

Figure 3: Inner Rail Release Clip
Outer rail attached to rack post3Inner rail release clip1
Inner rail attached to controller2
Step 5 (Optional) Secure the controller in the rack more permanently by using the two screws that are provided with the slide
rails. Perform this step if you plan to move the rack with controllers installed.
With the controller fully pushed into the slide rails, open a hinged slam latch lever on the front of the controller and insert
the screw through the hole that is under the lever. The screw threads into the static part of the rail on the rack post and
prevents the controller from being pulled out. Repeat for the opposite slam latch.
Installing the Cable Management Arm (Optional)
The CMA is reversible left to right. To reverse the CMA, see Reversing the Cable Management Arm (Optional),
on page 8 before installation.
Note
Step 1 With the controller pushed fully into the rack, slide the CMA tab of the CMA arm that is farthest from the controller onto
the end of the stationary slide rail that is attached to the rack post (see Figure 4: Attaching the Cable Management Arm
to the Rear of the Slide Rails, on page 8). Slide the tab over the end of the rail until it clicks and locks.
Step 2 Slide the CMA tab that is closest to the controller over the end of the inner rail that is attached to the controller (see Figure
4: Attaching the Cable Management Arm to the Rear of the Slide Rails, on page 8). Slide the tab over the end of the
rail until it clicks and locks.
Step 3 Pull out the width-adjustment slider that is at the opposite end of the CMA assembly until it matches the width of your
rack (see Figure 4: Attaching the Cable Management Arm to the Rear of the Slide Rails, on page 8).
Step 4 Slide the CMA tab that is at the end of the width-adjustment slider onto the end of the stationary slide rail that is attached
to the rack post (see Figure 4: Attaching the Cable Management Arm to the Rear of the Slide Rails, on page 8). Slide
the tab over the end of the rail until it clicks and locks.
Step 5 Open the hinged flap at the top of each plastic cable guide and route your cables through the cable guides as desired.
Installing the Controller
7
Installing the Controller
Installing the Cable Management Arm (Optional)

Figure 4: Attaching the Cable Management Arm to the Rear of the Slide Rails
CMA tab on width-adjustment slider
and end of stationary outer slide rail
3CMA tab on arm farthest from controller
and end of stationary outer slide rail
1
Rear of controller4CMA tab on arm closest to the controller
and end of inner slide rail attached to
controller
2
Reversing the Cable Management Arm (Optional)
Step 1 Rotate the entire CMA assembly 180 degrees. The plastic cable guides must remain pointing upward.
Step 2 Flip the tabs at the end of each CMA arm so that they point toward the rear of the controller.
Step 3 Pivot the tab that is at the end of the width-adjustment slider. Depress and hold the metal button on the outside of the tab
and pivot the tab 180 degrees so that it points toward the rear of the controller.
Installing the Controller
8
Installing the Controller
Reversing the Cable Management Arm (Optional)

Figure 5: Reversing the CMA
Metal button for rotating2CMA tab on end of width-adjustment slider1
Initial Controller Setup
For instructions on performing initial setup of controller, see the Cisco 8540 Wireless Controller Deployment
Guide .
System BIOS and Cisco IMC Firmware
Updating the BIOS and Cisco IMC Firmware
The BIOS and Cisco IMC firmware need not be upgraded when you first bring up the unit.
When you upgrade the BIOS firmware, you must also upgrade the Cisco IMC firmware to the same version
or the controller does not boot. Do not power off the controller until the BIOS and Cisco IMC firmware are
matching or the controller does not boot.
Cisco provides the Cisco Host Upgrade Utility to assist with simultaneously upgrading the BIOS, Cisco IMC,
and other firmware to compatible levels.
Caution
After the firmware is upgraded, do not reset the system to factory default. Doing so will delete the initial BIOS
setup and boot orders.
Warning
The controller uses firmware obtained from and certified by Cisco. Cisco provides release notes with each
firmware image.
Installing the Controller
9
Installing the Controller
Initial Controller Setup

The only supported method to update the firmware is using the Cisco Host Upgrade Utility.
Accessing the System BIOS
You can change the BIOS settings for your controller. Detailed instructions are also printed on the BIOS
screens.
Step 1 Enter the BIOS setup utility by pressing the F2 key when prompted during bootup.
The version and build of the current BIOS are displayed on the Main page of the utility.
Note
Step 2 Use the arrow keys to select the BIOS menu page.
Step 3 Highlight the field to be modified by using the arrow keys.
Step 4 Press Enter to select the field that you want to change, and then modify the value in the field.
Step 5 Press the right arrow key until the Exit menu screen is displayed.
Step 6 Follow the instructions on the Exit menu screen to save your changes and exit the setup utility (or Press F10). You can
exit without saving changes by pressing Esc.
Installing the Controller
10
Installing the Controller
Accessing the System BIOS