Cisco 40-Gigabit and 100-Gigabit CFP Transceiver... Quick start guide

Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Cisco 40-Gigabit and 100-Gigabit CFP
Transceiver Modules Installation Note
Revised: July 5, 2012
The CFP transceiver module connects the electrical circuitry of the platform with an optical network.
This installation note provides instructions for installing the 40-Gigabit and 100-Gigabit CFP transceiver
modules.
Contents
This document contains these sections:
•Overview, page 2
•Safety, page 6
•Required Tools, page 12
•Installing the CFP Transceiver, page 12
•Removing the CFP Transceiver, page 16
•Translated Safety Warnings, page 18
•Obtaining Documentation and Submitting a Service Request, page 24
Product Numbers: CFP-100G-LR4 CFP-40G-SR4 CFP-40G-LR4
CVR-CPR-4SFP10G CFP-40G-FR CFP-100G-SR10

2
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
Overview
Overview
The 40-Gigabit and 100-Gigabit Ethernet CFP transceivers are hot-swappable I/O devices that plug into
40-Gigabit and 100-Gigabit Ethernet module ports. Figure 1 shows a CFP-40G-LR4 module with duplex
SC fiber connectors. The CFP-100G-LR4 and CFP-40G-FR also use duplex SC fiber connectors.
Figure 1 CFP-40G-LR4 Transceiver Features
Figure 2 shows a CFP-40G-SR4 module with a 12-fiber MPO connector. The CFP-100G-SR10 module
is very similar, but uses a 24-fiber MPO connector.
1Captive installation screws 3Transmit optical bore, SC connector
2Optical bore dust plug 4Receive optical bore, SC connector
281584
2
1
3
4

3
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
Overview
Figure 2 CFP-40G-SR4 Transceiver Features
Figure 3 shows a CVR-CFP-4SFP10G module. This is an adapter module that converts a Cisco switch
or router CFP port to four 10-Gigabit SFP+ ports. The SFP+ transceivers are not included with the
converter module.
Figure 3 CVR-CFP-4SFP10G CFP to Four SFP+ Converter Module
1Captive installation screws 3Transmit and receive multifiber optical bore,
MPO/MTP connector
2Optical bore dust plug
332450
1Captive installation screws 210G SFP+ ports (4X)

4
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
Overview
Table 1 lists the currently supported types of CFP transceivers.
Note The SC and MPO connectors on the optical CFP transceivers support network interface cables with
either Physical Contact (PC) or Ultra-Physical Contact (UPC) flat polished face types. The SC and MPO
connectors on the optical CFP transceivers do not support network interface cables with an Angle
Polished Connector (APC) polished face type.
Table 1 CFP Transceiver Product Numbers and Descriptions
CFP Transceiver Module
Product Number
Transceiver Description
100-Gigabit
CFP-100G-LR4 Cisco 100GBASE-LR4 CFP transceiver module for SMF, 1310 nm
window, SC connector
CFP-100G-SR10 Cisco 100GBASE-SR10 CFP transceiver module for MMF, 850 nm,
24-fiber MPO/MTP connector
40-Gigabit
CFP-40G-SR4 Cisco 40GBASE-SR4 CFP transceiver module forMMF, 850 nm,
12-fiber MPO/MTP connector
CFP-40G-LR4 Cisco multirate 40GBASE-LR4 and OTU3 C4S1-2D1 for SMF,
1310 nm window, SC connector
CFP-40G-FR Cisco multirate 40GBASE-FR and OTU3 VSR2000-3R2 CFP
transceiver module for SMF, 1550 nm, SC connector
CVR-CFP-4SFP10G Cisco FourX CFP to four SFP+ Converter Module

5
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
Overview
Table 2 lists the 100-Gigabit CFP port cabling specifications. Table 3 lists the optical transmit and
receive specifications for 100-Gigabit CFP transceivers.
Note The minimum cabling distance for the CFP-100G-LR4, CFP-40G-FR, and the CFP-40G-LR4
transceivers is 6.56 feet (2 meters). The minimum cabling distance for the CFP-40G-SR4 and the
CFP-100G-SR10 transceivers is 1.64 feet (0.5 m).
Table 2 CFP Optical Transceiver Module Cabling Specifications
CFP Transceiver
Module Model
Wavelength
(nm)
Fiber Type Core Size
(µm)
Modal
Bandwidth
(MHz/km)
Cabling Distance
100-Gigabit
CFP-100G-LR4 1310 SMF G.652 — 6.28 miles (10 km)
CFP-100G-SR10 850 MMF 50.0
50.0
2000 (OM3)
4700 (OM4)
328.1 ft (100 m)
492.1 ft (150 m)
40-Gigabit
CFP-40G-SR4 850 MMF 50.0
50.0
50.0
500 (OM2)
2000 (OM3)
4700 (OM4)
98.4 ft (30 m)
328.1 ft (100 m)
492.1 ft (150 m)
CFP-40G-LR4 1310 SMF G652 — 6.28 miles (10 km)
CFP-40G-FR 1550 SMF G.652 — 1.24 miles (2 km)
Table 3 CFP Transceiver Module Optical Transmit and Receive Specifications
CFP Transceiver
Module Model
Transceiver Type Transmit
Power (dBm)
Receive Power
(dBm)
Transmit and Receive
Wavelength (nm)
100-Gigabit
CFP-100G-LR4 100GBASE-LR4,
1310-nm SMF
4.5 per lane
(Max)
–4.3 per lane
(Min)
4.5 per lane
(Max)
–10.6 per lane
(Min)
Four lanes:
1295.6
1300.1
1304.6
1309.1
CFP-100G-SR10 100GBASE-SR10 -1.0 per lane
(Max)
-7.6 per lane
(Min)
2.4 per lane
(Max)
-9.5 per lane
(Min)
Ten lanes 840 to 860
40-Gigabit
CFP-40G-SR4 40GBASE-SR4,
850 nm MMF
2.4 per lane
(Max)
–7.6 per lane
(Min)
2.4 per lane
(Max)
–9.5 per lane
(Min)
Four lanes 840 to 860

6
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
Safety
Safety
Safety warnings appear throughout this publication in procedures that may harm you if performed
incorrectly or are ignored. A warning symbol precedes each warning statement.
Statement 1071—Warning Definition
CFP-40G-LR4 40GBASE-LR4,
1310-nm SMF
2.3 per lane
(Max)
–7 per lane
(Min)
2.3 per lane
(Max)
–13.7 per lane
(Min)
Four lanes:
1271
1291
1311
1331
OTU3 C4S1-2D1,
1310-nm SMF
2.3 per lane
(Max)
–2.3 per lane
(Min)
2.3 per lane
(Max)
–9 per lane
(Min)
Four lanes:
1271
1291
1311
1331
CFP-40G-FR 40GBASE-FR and
OTU3
VSR2000-3R2,
1550 nm SMF
3.0 (Max)
0.0 (Min)
3.0 (Max)
-6.0 (Min)
One lane, 1530 to
1565
Table 3 CFP Transceiver Module Optical Transmit and Receive Specifications
CFP Transceiver
Module Model
Transceiver Type Transmit
Power (dBm)
Receive Power
(dBm)
Transmit and Receive
Wavelength (nm)
Warning IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this
device.
Statement 1071
SAVE THESE INSTRUCTIONS
Waarschuwing
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan
veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij
elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard
praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de
waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt
raadplegen.
BEWAAR DEZE INSTRUCTIES

7
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
Safety
Varoitus
TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin
käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu
onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen
mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien
lausuntonumeroiden avulla.
SÄILYTÄ NÄMÄ OHJEET
Attention
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant
entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez
conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures
couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des
avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen
kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und
den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder
Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
Avvertenza
IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle
persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli
relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.
Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le
traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
Advarsel
VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du
begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med
elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten
av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne
enheten.
TA VARE PÅ DISSE INSTRUKSJONENE

8
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
Safety
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de
lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos
perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de
prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para
localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
GUARDE ESTAS INSTRUÇÕES
¡Advertencia!
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular
cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los
procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el
número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña
a este dispositivo.
GUARDE ESTAS INSTRUCCIONES
Varning!
VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.
Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och
känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av
varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna
anordning.
SPARA DESSA ANVISNINGAR

9
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
Safety
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões
corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os
circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o
número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de
segurança traduzidos que acompanham o dispositivo.
GUARDE ESTAS INSTRUÇÕES
Advarsel
VIGTIGE SIKKERHEDSANVISNINGER
Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for
legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de
involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til
undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de
oversatte advarsler, der fulgte med denne enhed.
GEM DISSE ANVISNINGER

10
Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Installation Note
OL-23946-01
Safety