Cisco 3640 Series User manual

Page1
Cisco 3640 Series Router-PBX Interoperability:
VIC 2BRI-NT/TE card to Alcatel 4400 PBX with
BRI ISDN QSIG Signaling
This document describes the interoperability and configuration of a Cisco 3640 series router with a VIC
2BRI-NT/TE card to an Alcatel 4400 PBX using BRI ISDN QSIG signaling. It includes the following
sections:
•System Components
•Configuration Tasks
•Caveats
System Components
PBX Model Alcatel 4400
PBX Release R3.2
Telephony Signaling BRI ISDN QSIG
Voice Gateway Cisco 3640 series router
Gateway Release Cisco IOS Release 12.2(1a)
VoX Protocol H.323
Configuration Tasks
See the following sections for configuration tasks for this feature:
•Set Up
•Alcatel PBX Configuration
•Cisco 3640 Series Router Configuration

Cisco3640SeriesRouter-PBXInteroperability:VIC2BRI-NT/TEcardtoAlcatel4400PBX withBRIISDNQSIG Signaling
Page2
Set Up This section includes the following information:
•Connectivity Diagrams
•Set Up Notes
Connectivity Diagrams
Figure 1: Test Configuration
Figure 1 represents the configuration used for testing: an Alcatel 4400PBX connected to a Cisco 3640
series router through an E1-QSIG connection.
Set Up Notes
The Cisco 3640 router with ISDN switch type setting of basic-qsig supports both protocol sides by using
the isdn protocol-emulate network/user command.
•The Alcatel 4400 supports both “USER” (slave) and “NETWORK” (master) protocol sides.
•The following options are of particular interest:
•Trunk interface type must be set to BRA2.
•Network/User options are set in the Board/Digital Access Options menu. Network mode must be
set to Yes for Master/Network or No for Slave/User.
•Access Type must be set to T0.
•Q931 signal variant is used to determine Protocol type. This option was set toISDN ABC-F.
The Alcatel 4400 PBX configuration screen for the BRI trunk interface is reached using both Alcatel Board
and Board\Digital Access menus, setting the BRI physical layer parameters.
Phone C
x3000
Basic Call Setup End-to-End Configuration
VoIP
PBX2: Alcatel 4400,
slot 4
Phone B
x3002
Phone D
x3003
Phone A
x3001
PBX #1 PBX #2
Phone E
x N/A
Phone F
x N/A
PBX1: Alcatel 4400,
slot3
ISDN Type:
E1-QSIG
ISDN Type:
E1-QSIG
7206VXR_A 7206VXR_B

Cisco3640SeriesRouter-PBXInteroperability:VIC2BRI-NT/TEcard toAlcatel4400PBX withBRIISDNQSIG Signaling
Page3
Alcatel PBX Configuration
Alcatel PBX Version Information
•Software: Version R3.2
•Hardware: BRA2, 3BA23076.
Version Information
\compidea\Node
Node Number (reserved) 1
Software Version R3.2
Version name c1.712
Patch No. 5
Notes
Object Identity
Node Number (reserved) 1
Ethernet Notes
Netmask
Local CPU
Name x000000_tun
IP Address 172.30.253.253
Twin Cpu
Name
IP Address
Main Cpu
Name xm000000
IP Address 10.253.253.3
StandBy Cpu
Name
IP Address
SL Notes
IP/X25 Tunnel Notes
Netmask 255.255.0.0
Local Node
Name x000000_tun
IP Address 172.30.253.253
Alcatel PBX Sample Configuration
See the following sections for sample configuration information:
•Trunk Cards Were Configured the Same
•Digital Access Options
•Trunk Group
•Trunk Detail

Cisco3640SeriesRouter-PBXInteroperability:VIC2BRI-NT/TEcard toAlcatel4400PBX withBRIISDNQSIG Signaling
Page4
Trunk Cards Were Configured the Same
Interface type must be set to BRA2.
\compidea\Shelf::0\Board::9
Board Address 9
Interface Type BRA2
Usage State Active
Operational State Enabled
Main/Standby State Main (Master)
Number Of Sets Being Connect. 1
Country Protocol Type Default
Incidents Teleservice YES
ISDN Board Layer 2 Parameters
Retransmission Timer 100
TEI Identity Check Timer 100
Polling Timer 1000
Nb_Of_Retransmission 3
Max Frame Size (Bytes) 260
Window Size In Frames SAPI S T0 1
Window Size In Frames SAPI P T0 3
Window Size In Frames SAPI S T2 7
Window Size In Frames SAPI P T2 7
Digital Access Options
Network mode must be set toYes for Master/Network or No for Slave/User.
Access Type must be set toT0.
\compidea\Shelf::0\Board::9\Digital Access::2
T0/T2 Access No. 2
Access Type T0
Synchronisation Priority 255
Network Mode NO
Max Nb Of Used B Channels 2
Max_Nb_Of_Compressed_B_Channels 0
TieLine Mode NO
Access Type S0 NO
Reserved1 NO
Reserved2 NO
Network Date Time Update NO
Trunk Group
Q931 signal variant is used to determine Protocol type. ISDN ABC-Fis Alcatel proprietary.
\compidea\Trunk Groups::8
Trunk Group Id 8
Trunk Group Type T0
Trunk Group Name BRI-ABC-F
Node number 1
Transcom Trunk Group False
Auto.reserv.by Attendant False
Overflow trunk group No. -1
Tone on seizure True

Cisco3640SeriesRouter-PBXInteroperability:VIC2BRI-NT/TEcard toAlcatel4400PBX withBRIISDNQSIG Signaling
Page5
Private Trunk Group False
Security Patrol False
Q931 signal variant ABC-F
Number Compatible With -1
Number Of Digits To Send 4
Remote Network 15
Shared Trunk Group False
auto.DTMF dialing on outgoing call NO
Public Network Category 0
DDI transcoding False
Special Services Nothing
Can support UUS in SETUP True
Trunk Detail
\compidea\Trunk Groups::8\Trunk Group::1
Instance (reserved) 1
Trunk Group Type T0
Public Network Ref.
Dialling end to end NO
DTMF end to end signal. NO
Trunk group used in DISA NO
DISA Secret Code
VG for non-existent No. YES
Routing To Executive NO
Trunk Category Id 18
Nb of digits unused (ISDN) 4
B Channel Choice YES
Channels Reserved By Attend. 0
Dissuasion For ACD NO
DTO joining NO
Enquiry Call On B Channel NO
Automated Attendant NO
Calling party Rights category 0
Entity Number 0
TS Overflow YES
Number To Be Added
Supervised by Routing NO
VPN Cost Limit for Incom.Calls 0
Immediat Trk Listening For VPNCall YES
VPN TS % 50
Csta Monitored NO
Max.% of trunks out CCD 0
Charge Calling And ADN Creation NO
Ratio analog.to ISDN tax
TS Distribution on Accesses YES
Use Split Acces NO
Heterogeneous Remote Network NO
Barring mode Not barred
ARS class of service 31
Quality profile for voice on IP Profile #1
IP compression type Default
Use of volume in system YES

Cisco3640SeriesRouter-PBXInteroperability:VIC2BRI-NT/TEcard toAlcatel4400PBX withBRIISDNQSIG Signaling
Page6
Cisco 3640 Series Router Configuration
The following is the configuration of the Cisco 3640 series router connected to the Alcatel 4400 ISDN BRI
ISDN QSIG signaling interface.
•Cisco 3640 Series Router Version Information
•Cisco 3640 Series Router Sample Configuration
Cisco 3640 Series Router Version Information
•Cisco IOS™ (C3640-JS-M), Version 12.2(1a).
•Cisco 3640 (R4700) processor (revision 0x00) with 59392K/6144K bytes of f memory.
3640_B#
3640_B#sho ver
Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3640-JS-M), Version 12.2(1a), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Sat 26-May-01 02:40 by pwade
Image text-base: 0x60008950, data-base: 0x61492000
ROM: System Bootstrap, Version 11.1(7)AX [kuong (7)AX], EARLY DEPLOYMENT RELEASE SOFTWARE
(fc2)
3640_B uptime is 1 hour, 21 minutes
System returned to ROM by power-on
System image file is "flash:c3640-js-mz.122-1a.bin"
cisco 3640 (R4700) processor (revision 0x00) with 59392K/6144K bytes of memory.
Processor board ID 05247801
R4700 CPU at 100Mhz, Implementation 33, Rev 1.0
Channelized E1, Version 1.0.
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
Primary Rate ISDN software, Version 1.1.
Basic Rate ISDN software, Version 1.1.
2 Ethernet/IEEE 802.3 interface(s)
31 Serial network interface(s)
2 ISDN Basic Rate interface(s)
2 Channelized E1/PRI port(s)
2 Voice FXS interface(s)
4 Voice NT or TE BRI interface(s)
DRAM configuration is 64 bits wide with parity disabled.
125K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
3640_B#
3640_B#
Cisco 3640 Series Router Sample Configuration
The following is a sample configuration of the Cisco 3640 series router directly connected to Alcatel 4400
PBX, slot 3 ISDN PRI interface.
3640_B#
3640_B#sho diag
Slot 0:
Combo 2E, 2W Port adapter, 4 ports
Port adapter is analyzed

Cisco3640SeriesRouter-PBXInteroperability:VIC2BRI-NT/TEcard toAlcatel4400PBX withBRIISDNQSIG Signaling
Page7
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware revision 1.2 Board revision B0
Serial number 7687847 Part number 800-01171-04
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 1E 01 02 00 75 4E A7 50 04 93 04 00 00 00 00
0x30: 58 00 00 00 98 02 28 17 FF FF FF FF FF FF FF FF
Slot 1:
High Density Voice Port adapter
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 1.0
Top Assy. Part Number : 800-03567-01
Board Revision : A0
Deviation Number : 0-0
Fab Version : 02
PCB Serial Number : JAB03350B9K
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 00 CC 41 01 00 C0 46 03 20 00 0D EF 01
0x10: 42 41 30 80 00 00 00 00 02 02 C1 8B 4A 41 42 30
0x20: 33 33 35 30 42 39 4B 03 00 81 00 00 00 00 04 00
0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC Slot 0:
E1 (2 Port) Multi-Flex Trunk WAN Daughter Card
Hardware revision 1.0 Board revision B0
Serial number 18779824 Part number 800-04479-01
Test history 0x0 RMA number 00-00-00
Connector type PCI
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 23 01 00 01 1E 8E B0 50 11 7F 01 00 00 00 00
0x30: 58 00 00 00 00 02 25 00 FF FF FF FF FF FF FF FF
HDV firmware: Compiled Wed 04-Oct-00 20:58 by mani
HDV memory size 524280 heap free 180601
Slot 2:
4 PORT Voice PM for MARs Port adapter
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware revision 1.1 Board revision D0
Serial number 15077168 Part number 800-02491-02
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 65 01 01 00 E6 0F 30 50 09 BB 02 00 00 00 00
0x30: 68 00 00 00 99 07 31 17 FF FF FF FF FF FF FF FF
WIC Slot 0:
FXS Voice daughter card (2 port)
Hardware revision 1.1 Board revision F0
Serial number 14674684 Part number 800-02493-01
Test history 0x0 RMA number 00-00-00
Connector type Wan Module
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 0E 01 01 00 DF EA FC 50 09 BD 01 00 00 00 00
0x30: 78 00 00 00 99 07 12 01 FF FF FF FF FF FF FF FF

Cisco3640SeriesRouter-PBXInteroperability:VIC2BRI-NT/TEcard toAlcatel4400PBX withBRIISDNQSIG Signaling
Page8
Slot 3:
4 PORT Voice PM for MARs Port adapter
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware revision 1.1 Board revision H0
Serial number 25140072 Part number 800-02491-02
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 65 01 01 01 7F 9B 68 50 09 BB 02 00 00 00 00
0x30: 88 00 00 00 01 02 15 17 FF FF FF FF FF FF FF FF
WIC Slot 0:
NT or TE BRI Voice daughter card (2 port)
Hardware revision 1.255 Board revision V7
Serial number 4294967295 Part number 800-11534335-255
Test history 0xFF RMA number 255-255-255
Connector type PCI
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 32 01 FF FF FF FF FF FF FF FF FF FF FF FF FF
0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
3640_B#
3640_B#
3640_B#sho interfaces bri 3/0
BRI3/0 is up, line protocol is up (spoofing)
Hardware is Voice NT or TE BRI
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation VOICE, loopback not set
Last input 00:00:00, output never, output hang never
Last clearing of "show interface" counters 00:00:12
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 48 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
2 packets input, 8 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
3640_B#
3640_B#
3640_B#
3640_B#
3640_B#sho run
Building configuration...
Current configuration : 2259 bytes
!
version 12.2
no service single-slot-reload-enable
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
no service dhcp
!
hostname 3640_B
!
boot system flash
logging rate-limit console 10 except errors
!
voice-card 1

Cisco3640SeriesRouter-PBXInteroperability:VIC2BRI-NT/TEcard toAlcatel4400PBX withBRIISDNQSIG Signaling
Page9
!
ip subnet-zero
!
!
no ip finger
no ip domain-lookup
ip host whiz 171.69.1.162
ip host dirt 171.69.1.129
ip host danube 171.69.17.14
!
no ip dhcp-client network-discovery
isdn switch-type basic-qsig
call rsvp-sync
cns event-service server
!
!
!
!
!
!
!
controller E1 1/0
shutdown
framing NO-CRC4
ds0-group 1 timeslots 1 type r2-analog r2-compelled
cas-custom 1
!
controller E1 1/1
shutdown
pri-group timeslots 1-31
!
!
interface Tunnel1
no ip address
!
interface Ethernet0/0
ip address 100.100.100.2 255.255.255.0
no ip mroute-cache
half-duplex
no cdp enable
!
interface Ethernet0/1
ip address 171.69.231.23 255.255.255.0
no ip mroute-cache
half-duplex
no cdp enable
!
interface Serial1/1:15
no ip address
no logging event link-status
shutdown
isdn switch-type primary-net5
isdn overlap-receiving
isdn protocol-emulate network
isdn incoming-voice voice
no isdn T309-enable
isdn T203 30000
isdn T310 60000
isdn bchan-number-order ascending
no cdp enable
!
interface BRI3/0
no ip address
no ip route-cache
no ip mroute-cache
isdn switch-type basic-qsig
isdn overlap-receiving
isdn protocol-emulate network
isdn layer1-emulate network
isdn incoming-voice voice
isdn T310 40000
isdn skipsend-idverify

Cisco3640SeriesRouter-PBXInteroperability:VIC2BRI-NT/TEcard toAlcatel4400PBX withBRIISDNQSIG Signaling
Page10
!
interface BRI3/1
no ip address
isdn switch-type basic-net3
isdn T310 120000
!
ip kerberos source-interface any
ip classless
no ip http server
!
dialer-list 1 protocol ip permit
no cdp run
!
!
voice-port 1/0:1
!
voice-port 1/1:15
!
voice-port 2/0/0
!
voice-port 2/0/1
!
voice-port 3/0/0
compand-type a-law
!
voice-port 3/0/1
!
dial-peer cor custom
!
!
!
dial-peer voice 2 pots
destination-pattern 4200
port 2/0/0
!
dial-peer voice 4 voip
destination-pattern 2...
session target ipv4:100.100.100.1
!
dial-peer voice 3 pots
destination-pattern 3...
direct-inward-dial
port 3/0/0
prefix 3
!
dial-peer voice 6 voip
destination-pattern 5...
session target ipv4:100.100.100.1
!
!
line con 0
transport input none
line aux 0
line vty 0 4
no login
!
end
3640_B#
3640_B#
Caveats
•Calling/Called Number is not shown on Alcatel phone display (one line display phone show Name
only) due to limitation on one line display phone.