Cisco ASR 1001-HX Manual

Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware
Installation Guide
First Published: 2016-10-17
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,
INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH
THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,
CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version
of the UNIX operating system. All rights reserved. Copyright ©1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS.
CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT
LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network
topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional
and coincidental.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: http://
www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership
relationship between Cisco and any other company. (1110R)
©2016 Cisco Systems, Inc. All rights reserved.

CONTENTS
Preface Preface ix
Document Revision History ix
Document Objectives ix
Audience ix
Document Organization x
Conventions xi
Related Documentation xii
Obtaining Documentation and Submitting a Service Request xii
CHAPTER 1 Overview 1
Hardware Features 1
Front View 3
Slot Numbering 5
Built-In SFP and SFP+ Ports 5
Management and Storage Connections 7
LEDs 8
Rear View 10
Cisco Product Identification Standard 11
Unique Device Identifier 12
Serial Number and PID/VID Label Location 14
CHAPTER 2 Supported Hardware Components 15
Supported EPAs 15
Supported Transceivers 17
Supported Crypto Module 19
Supported DIMM Upgrade 20
Power Supplies 20
Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide
iii

AC Power Supply 21
DC Power Supply 22
Power Supply LEDs 24
Power Supply Fans 25
Power Cords 25
CHAPTER 3 Preparing Your Site for Installation 27
Prerequisites and Preparation 27
Site Planning Checklist 28
Safety Guidelines 28
Safety Warnings 29
Safety Recommendations 29
Cautions and Regulatory Compliance Statements for NEBS 29
Standard Warning Statements 30
General Safety Warnings 31
Site Planning 34
General Precautions 34
Site Selection Guidelines 35
Site Environmental Requirements 35
Physical Characteristics 36
Site Power Guidelines 37
Electrical Circuit Requirements 38
Site Cabling Guidelines 38
Console Port Connections 39
USB Serial Console 39
Interference Considerations 40
Electromagnetic Interference 40
Radio Frequency Interference 40
Lightning and AC Power Fault Interference 41
Rack-Mounting Guidelines 41
Precautions for Rack-Mounting 41
General Rack-Selection Guidelines 41
Guidelines for 23-in. (Telco) Racks 42
Equipment Rack Guidelines 42
Locating for Safety 42
Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide
iv
Contents

Locating for Easy Maintenance 43
Locating for Proper Airflow 43
Preventing Electrostatic Discharge Damage 43
Electrical Safety 44
Chassis-Lifting Guidelines 45
Tools and Equipment 45
Unpacking and Verifying Shipping Contents 46
Checking the Shipping Container Contents 46
Installation Checklist 47
CHAPTER 4 Installing the Router 49
Installation Methods 49
Guidelines for a Standalone Equipment Shelf or Tabletop Installation 50
Installing the Router on a Standalone Equipment Shelf or Tabletop 51
Guidelines for Rack Installation 51
Verifying Rack Dimensions 53
Attaching the Front Rack-Mount Brackets 53
Attaching the Rear Rack-Mount Brackets 55
Mounting the Router in the Rack 57
Two-Post Rack Installation 57
Four-Post Rack Installation 59
Attaching the Cable Management Bracket 62
Chassis Ground Connection 64
Recommended Tools and Supplies 64
Attaching a Chassis Ground Connection 65
Connecting Cables 67
Connecting the Console and Auxiliary Port Cables 68
Connecting to the Mini USB Console Port 69
Management Ethernet Port Cable Connection 69
CHAPTER 5 Power Up and Initial Configuration 71
Checking Conditions Prior to System Startup 71
Powering Up the Router 72
Performing the Initial Configuration on the Router 74
Using the Cisco setup Command Facility 74
Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide
v
Contents

Completing the Configuration 77
Using the Cisco IOS-XE CLI—Manual Configuration 78
Configuring the Router Hostname 79
Configuring the Enable and Enable Secret Passwords 80
Configuring the Console Idle Privileged EXEC Timeout 81
Gigabit Ethernet Management Interface Overview 82
Default Gigabit Ethernet Configuration 82
Configuring Gigabit Ethernet Interfaces 82
Saving Your Router Configuration 84
Verifying the Initial Configuration 84
Powering Off the Router Safely 85
Environmental Monitoring and Reporting Functions 85
Alarm Monitoring 86
Environmental Monitoring 87
Fan Failures 87
Reporting Functions 88
CHAPTER 6 License Verification 95
Viewing the Cisco IOS License Level 95
Viewing License Information 96
Port Licensing 101
Port Licensing for the Cisco ASR 1001-HX Router 101
Licensing Scenarios for Cisco ASR 1001-HX Router 103
Port Licensing for the Cisco ASR 1002-HX Router 106
Licensing Scenarios for Cisco ASR 1002-HX Router 107
Evaluation License Features 108
Configuring the Crypto Throughput Level 109
CHAPTER 7 Removing and Replacing FRUs 111
Removing and Replacing the Power Supplies 111
Removing AC Power Supplies 112
Installing AC Power Supplies 112
Removing DC Input Power Supplies 113
Installing DC Input Power Supplies 113
Wiring the DC Input Power Source 115
Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide
vi
Contents

Removing and Replacing USB Flash Memory Stick 117
Removing and Replacing a DIMM 117
Removing a DIMM from a Cisco ASR 1001-HX Router 118
Replacing a DIMM in a Cisco ASR 1001-HX Router 121
Removing a DIMM from a Cisco ASR 1002-HX Router 123
Replacing a DIMM in a Cisco ASR 1002-HX Router 126
Removing and Replacing an EPA 128
Electrostatic Discharge Prevention 128
Removing an EPA 129
Replacing an EPA 130
Removing and Replacing Fans 131
Removing the Fans from a Cisco ASR 1001-HX Router 131
Replacing the Fans in a Cisco ASR 1001-HX Router 134
Removing the Fans from a Cisco ASR 1002-HX Router 136
Replacing the Fans in a Cisco ASR 1002-HX Router 139
Installing the Crypto Module 140
Installing the Crypto Module in a Cisco ASR 1001-HX Router 140
Installing the Crypto Module in a Cisco ASR 1002-HX Router 142
Repacking the Router 144
APPENDIX A Technical Specifications 145
Cisco ASR 1001-HX Router Specifications 145
Cisco ASR 1002-HX Router Specifications 146
APPENDIX B Port Signals and Pinouts 147
Management Ethernet Port Signals and Pinouts 147
Console Port Signals and Pinouts 147
Auxiliary Port Signals and Pinouts 148
Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide
vii
Contents

Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide
viii
Contents

Preface
•Document Revision History, page ix
•Document Objectives, page ix
•Audience, page ix
•Document Organization, page x
•Conventions, page xi
•Related Documentation, page xii
•Obtaining Documentation and Submitting a Service Request, page xii
Document Revision History
The following table records the changes made to this document.
Change SummaryDate
Added the Cisco ASR 1001-HX Router.October 2016
First version of the document.May 2016
Document Objectives
This publication describes the installation of the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router
and replacement or upgrade of field-replaceable units (FRUs).
Audience
This publication is primarily designed for persons responsible for installing, maintaining, and troubleshooting
the Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router. The users of this guide should:
Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide
ix

•Be familiar with electronic circuitry and wiring practices.
•Have experience working as electronic or electromechanical technicians.
•Have experience in installing high-end networking equipment.
Certain procedures described in this guide require a certified electrician.Note
Document Organization
The following table describes the chapters and appendixes in this installation guide:
DescriptionChapter and Appendix
Provides an overview of the Cisco ASR 1001-HX Router
and Cisco ASR 1002-HX Router
Overview1
Provides an overview of the hardware components for the
Cisco ASR 1001-HX Router and Cisco ASR 1002-HX
Router
Supported Hardware Components2
Provides site preparation guidelines for installing the Cisco
ASR 1001-HX Router and Cisco ASR 1002-HX Router
Preparing Your Site for Installation3
Provides information about the installation methods and
steps to install the Cisco ASR 1001-HX Router and Cisco
ASR 1002-HX Router
Installing the Router4
Provides basic system startup and initial configuration
information
Power Up and Initial Configuration5
Provides information about the Cisco ASR 1001-HX
Router and Cisco ASR 1002-HX Router licenses
License Verification6
Provides instructions for removing and replacing the
various FRUs in the Cisco ASR 1001-HX Router and Cisco
ASR 1002-HX Router
Removing and Replacing FRUs7
Provides router specifications for the Cisco ASR 1001-HX
Router and Cisco ASR 1002-HX Router
Technical SpecificationsA
Lists pinout specifications for the Cisco ASR 1001-HX
Router and Cisco ASR 1002-HX Router
Port Signals and PinoutsB
Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide
x
Preface
Document Organization