Cisco ASR 1006 User manual

Cisco ASR 1006 Router Overview and Installation
This chapter describes the Cisco ASR 1006 Router and the procedures for installing the Cisco ASR 1006
Router on an equipment shelf or in equipment racks. It also describes how to connect interface and power
cables.
This chapter contains the following sections:
•Cisco ASR 1006 Router Description, page 1
•Installation Methods, page 5
•General Rack Installation Guidelines, page 5
•Guidelines for an Equipment Shelf or Tabletop Installation, page 7
•Equipment Shelf or Tabletop Installation, page 8
•Rack-Mounting the Cisco ASR 1006 Router, page 10
•Attaching the Chassis Rack-Mount Brackets, page 11
•Installing the Cisco ASR 1006 Router in a Rack, page 15
•Attaching the Cable-Management Brackets, page 20
•Attaching a Chassis Ground Connection, page 23
•Connecting the Shared Port Adapter Cables, page 25
•Connecting the Console and Auxiliary Port Cables, page 25
•Connecting Power to the Cisco ASR 1006 Router, page 27
•Connecting a Terminal to the Cisco ASR 1000 Series RP Console Port, page 38
•Connecting the System Cables, page 41
•Attaching Cable Retention Bracket on AC Power Supply, page 41
Cisco ASR 1006 Router Description
The Cisco ASR 1006 Router supports full-width card modules. It is designed with a single midplane with
connectors on one interface midplane. The Cisco ASR 1006 Router supports:
Cisco ASR 1000 Series Router Hardware Installation Guide
1

•Three Cisco ASR 1000 Series SPA Interface Processors (SIPs)
•Twelve SPA slots
•Two embedded services processors (Cisco ASR1000-ESP10, Cisco ASR1000-ESP20, Cisco
ASR1000-ESP40, or Cisco ASR1000-ESP100)
Cisco ASR1000-ESP40 and Cisco ASR1000-ESP100 are supported on Cisco ASR 1006 Router only if
Cisco ASR1000-RP2 is installed on the router.
Note
•Two Cisco ASR 1000 Series Route Processors (Cisco ASR1000-RP1 or Cisco ASR1000-RP2
)
•Dual (redundant) AC and DC power supplies
This section contains the following topics:
Front View
The following image shows the Cisco ASR 1006 Router with modules and filler plates installed.
Figure 1: Cisco ASR 1006 Router — Front View
ASR 1000 Series SIP slot
0
5Slot R0 with ASR 1000
Series RP
1
ASR 1000 Series SIP slot
1
6Slot R1 with ASR 1000
Series RP
2
Cisco ASR 1000 Series Router Hardware Installation Guide
2
Cisco ASR 1006 Router Overview and Installation
Front View

ASR 1000 Series SIP slot
2
7Slot F0 with ASR 1000
Series ESP
3
Slot F1 with ASR 1000
Series ESP
4
Rear View
The following image shows the rear of the Cisco ASR 1006 Router with the ASR1006-PWR-AC power supply
installed.
Figure 2: Cisco ASR 1006 Router Rear View with the AC Power Supply (ASR1006-PWR-AC)
AC power supply handle5AC power supply fan1
AC power inlet6AC power supply DB-25
alarm connector—A
female DB-25 sub
connector which enables
you to attach an external
alarm monitoring facility
to the router, thus
supporting a telco-style of
handling alarm conditions
in the router.
For a description of the
DB-25 alarm connector,
see the “How Cisco
ASR1000-RP Alarm
Monitoring Works”
section on page 2-22 .
2
Cisco ASR 1000 Series Router Hardware Installation Guide
3
Cisco ASR 1006 Router Overview and Installation
Rear View

AC power supply
Standby switch. A
Standby switch is not
considered a disconnect.
7Cable tie wrap tabs3
AC power supply LEDs8AC power supply captive
screws
4
Internal fans draw cooling air into the chassis and across internal components to maintain an acceptable
operating temperature. (See Figure 2: Cisco ASR 1006 Router Rear View with the AC Power Supply
(ASR1006-PWR-AC), on page 3.) The fans are located at the rear of the chassis. A two-hole grounding
lug is located on the side of the chassis. Two power supplies, either two AC power supplies or two DC power
supplies, are accessed from the rear of the router.
You have already unpacked your chassis and read all the site requirements for your new equipment.
Proceed with the installation.
Note
Do not combine AC and DC power supplies in the same chassis.Note
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with
standard practices for preventing accidents. Use the statement number provided at the end of each warning
to locate its translation in the translated safety warnings that accompanied this device. Statement 1071
Warning
Before you install, operate, or service the system, read the Regulatory Compliance and Safety Information
for Cisco ASR 1000 Series Aggregation Services Routers publication. This document provides important
safety information you should know before working with the system. Statement 200
Warning
You have already unpacked your chassis and read all the site requirements for your new equipment.
Proceed with the installation.
Note
Cisco ASR 1006 Router Slot Numbering
The Cisco ASR 1006 Router is designed with each slot numbered as shown in Figure 3: Cisco ASR 1006
Router —Slot Numbering, on page 4.
Figure 3: Cisco ASR 1006 Router — Slot Numbering
Cisco ASR 1000 Series Router Hardware Installation Guide
4
Cisco ASR 1006 Router Overview and Installation
Rear View

ASR 1000 Series SIP slot
0
5Slot RP0 with ASR 1000
Series RP1
1
ASR 1000 Series SIP slot
1
6Slot RP1 with ASR 1000
Series RP1
2
ASR 1000 Series SIP slot
2
7Slot FP0 with ASR 1000
Series ESP
3
——
Slot FP1 with ASR 1000
Series ESP
4
The Cisco ASR 1006 Router contains three Cisco ASR 1000 Series SPA Interfaces (SIPs) that support four
subslots for the installation of SPAs.
Figure 4: Cisco ASR 1006 Router —SIP Subslots, on page 5 shows the Cisco ASR 1006 Router SPA
subslot location.
Figure 4: Cisco ASR 1006 Router — SIP Subslots
Installation Methods
Although rack-mounting is the preferred method of installation for the Cisco ASR 1006 Router, you can
mount the chassis:
•On an equipment shelf or tabletop
•In a19-inch wide (standard), 4-post equipment rack or two-post, using the rack-mount brackets in the
accessory kit
The Cisco ASR 1006 Router usually ships fully loaded. However, you can remove components from the
chassis to make the chassis lighter for your rack installation.
Note
General Rack Installation Guidelines
When planning your rack installation, consider the following guidelines:
•The Cisco ASR 1006 Router requires a minimum of 6 rack units (10.45 inches or 26.6 cm) of vertical
rack space. Measure the proposed rack location before mounting the chassis in the rack.
•Before using a particular rack, check for obstructions (such as a power strip) that could impair rack-mount
installation. If a power strip does impair a rack-mount installation, remove the power strip before installing
the chassis, and then replace it after the chassis is installed.
Cisco ASR 1000 Series Router Hardware Installation Guide
5
Cisco ASR 1006 Router Overview and Installation
Installation Methods

•Allow sufficient clearance around the rack for maintenance. If the rack is mobile, you can push it back
near a wall or cabinet for normal operation and pull it out for maintenance (installing or moving cards,
connecting cables, or replacing or upgrading components). Otherwise, allow 19 inches (48.3 cm) of
clearance to remove field-replaceable units
.
•Maintain a minimum clearance of 3 inches (7.62 cm) for the front and rear of the chassis for proper
chassis cooling. Avoid placing the chassis in an overly congested rack or directly next to another
equipment rack; otherwise, the heated exhaust air from other equipment can enter the inlet air vents and
cause an overtemperature condition inside the router.
•If rack space allows, it is recommended to leave one rack unit (1.75 inch or 4.45 cm) of vertical clearance
between the chassis and any equipment directly above it or below.
Depending on your installation and co-located equipment power dissipation, it is recommended to have
some air gap between chassis, if space allows, to reduce residual heating from one chassis to another.
Caution
•Always install heavier equipment in the lower half of a rack to maintain a low center of gravity to prevent
the rack from falling over.
•Install and use the cable-management brackets included with the Cisco ASR 1006 Router to keep cables
organized and out of the way of the cards and processors. Ensure that cables from other equipment
already installed in the rack do not impair access to the cards or require you to disconnect cables
unnecessarily to perform equipment maintenance or upgrades.
•Install rack stabilizers (if available) before you mount the chassis.
•Provide an adequate chassis ground (earth) connection for your router chassis
.
In addition to the preceding guidelines, review the precautions for avoiding excessive temperature conditions
in the “Electrical Safety”section on page 5-21 .
Table 1: Cisco ASR 1006 Router Dimensions and Weight, on page 6 provides the Cisco ASR 1006 Router
dimensions and weight information.
Table 1: Cisco ASR 1006 Router Dimensions and Weight
DimensionsCisco ASR 1006
22.50 in. (57.15 cm)(including card handles,
cable-management brackets, power supply handles)
Depth
10.45 in. (26.543 cm) - 6RU rack-mount per EIA
RS-310 standard
Height
17.25 in. (43.815 cm) - 19 inch rack-mountWidth
77.1 lb (34.971 kg) - fully configuredWeight
Cisco ASR 1000 Series Router Hardware Installation Guide
6
Cisco ASR 1006 Router Overview and Installation
General Rack Installation Guidelines

Guidelines for an Equipment Shelf or Tabletop Installation
The chassis should already be in the area where you will install it. If you have not determined where to install
your chassis, see the “Cisco ASR 1000 Series Routers Component Overview”section on page 2-1 for
information about site considerations.
If you are not rack-mounting your Cisco ASR 1000 series chassis, place it on a sturdy equipment shelf or
tabletop.
When installing the Cisco ASR 1006 Router on an equipment shelf or tabletop, ensure that the surface is clean
and that you have considered the following:
•The Cisco ASR 1006 Router requires at least 3 inches (7.62 cm) of clearance at the inlet and exhaust
vents (the front and top/rear sides of the chassis).
•The Cisco ASR 1006 Router should be installed off the floor. Dust that accumulates on the floor is drawn
into the interior of the router by the cooling fans. Excessive dust inside the router can cause
overtemperature conditions and component failures.
•There must be approximately 19 inches (48.3 cm) of clearance at the front and rear of the chassis to
install and replace FRUs, or to access network cables and equipment
.
•The Cisco ASR 1006 Router needs adequate ventilation. Do not install it in an enclosed cabinet where
ventilation is inadequate.
•Keep the cable-management brackets ready if you plan to install it on the front of the chassis.
•An adequate chassis ground (earth) connection exists for your router chassis (see the Attaching a Chassis
Ground Connection, on page 23).
•Always follow proper lifting practices as outlined in the “Chassis-Lifting Guidelines”section on page
5-23 when handling the chassis
.
Cisco ASR 1000 Series Router Hardware Installation Guide
7
Cisco ASR 1006 Router Overview and Installation
Guidelines for an Equipment Shelf or Tabletop Installation

Equipment Shelf or Tabletop Installation
At least two people are required to lift the chassis onto a tabletop or platform. To prevent injury, keep your
back straight and lift with your legs, not your back. Statement 164
Figure 5: Lifting the Chassis
The chassis in the image does not represent the Cisco ASR 1000 Series Router. This is only an example of
how to lift a Cisco chassis.
SUMMARY STEPS
1. Attach the front rack-mount brackets. Locate the threaded holes in the front sides of the chassis (first holes
beyond the vent holes) and use the package of black screws that shipped with the chassis.
2. Align the front rack-mount bracket to one side of the chassis.
3. Insert and tighten the screws on one side.
4. Repeat Step 2 through Step 3 on the other side of the chassis. Use at least 4 screws to secure the rack-mount
brackets to the chassis.
5. Gather the two cable-management brackets and screws shipped with the chassis. The following image
shows the cable-management brackets attached on the front of the Cisco ASR 1006 Router when the
chassis is placed on a table top or equipment shelf.
6. Screw the cable-management bracket to each side of the rack-mount brackets already attached to the
chassis. For each cable-management bracket, use two screws from the package of four screws.
7. Ensure that all the screws are securely tightened.
8. Go to the Attaching a Chassis Ground Connection, on page 23 for instructions about completing the
installation.
Cisco ASR 1000 Series Router Hardware Installation Guide
8
Cisco ASR 1006 Router Overview and Installation
Equipment Shelf or Tabletop Installation

DETAILED STEPS
Step 1 Attach the front rack-mount brackets. Locate the threaded holes in the front sides of the chassis (first holes beyond the
vent holes) and use the package of black screws that shipped with the chassis.
Step 2 Align the front rack-mount bracket to one side of the chassis.
Step 3 Insert and tighten the screws on one side.
Step 4 Repeat Step 2 through Step 3 on the other side of the chassis. Use at least 4 screws to secure the rack-mount brackets to
the chassis.
The cable-management brackets are installed on the chassis after you install the chassis rack-mount brackets.Note
Step 5 Gather the two cable-management brackets and screws shipped with the chassis. The following image shows the
cable-management brackets attached on the front of the Cisco ASR 1006 Router when the chassis is placed on a table
top or equipment shelf.
Make certain that the cable-management ‘U’feature device has the open end pointing upwards when you attach
it to the chassis.
Note
Figure 6: Attaching the Cable-Management Brackets to the Cisco ASR 1006 Router
Chassis front rack-mount
bracket
3Cable-management screws1
Cisco ASR 1000 Series Router Hardware Installation Guide
9
Cisco ASR 1006 Router Overview and Installation
Equipment Shelf or Tabletop Installation

——
Cable-management bracket2
Step 6 Screw the cable-management bracket to each side of the rack-mount brackets already attached to the chassis. For each
cable-management bracket, use two screws from the package of four screws.
Step 7 Ensure that all the screws are securely tightened.
Step 8 Go to the Attaching a Chassis Ground Connection, on page 23 for instructions about completing the installation.
Rack-Mounting the Cisco ASR 1006 Router
The Cisco ASR 1006 Router can be installed with both front or rear rack-mount brackets. The chassis
rack-mounting flanges are secured directly to the chassis before you lift it into the rack. For installing Cisco
ASR 1006 Router rack-mount brackets, go to:
Verifying Rack Dimensions
Before you install the chassis, measure the space between the vertical mounting flanges (rails) on your
equipment rack to verify that the rack conforms to the measurements shown in the following image.
SUMMARY STEPS
1. Mark and measure the distance between two holes on the left and right mounting rails.
2. Measure the space between the inner edges of the left front and right front mounting flanges on the
equipment rack.
DETAILED STEPS
Step 1 Mark and measure the distance between two holes on the left and right mounting rails.
The distance should measure 18.31 inches ± 0.06 inches (46.5 cm ± 0.15 cm).
Measure for pairs of holes near the bottom, middle and top of the equipment rack to ensure that the rack posts
are parallel.
Note
Step 2 Measure the space between the inner edges of the left front and right front mounting flanges on the equipment rack.
Cisco ASR 1000 Series Router Hardware Installation Guide
10
Cisco ASR 1006 Router Overview and Installation
Rack-Mounting the Cisco ASR 1006 Router