Cisco Small Business RV315W User manual

Quick Start Guide
Cisco RV315W Broadband Wireless VPN Router
Package Contents
•Cisco RV315W Broadband Wireless VPN Router
•Power Adapter and Power Cord
•Quick Start Guide
•Ethernet Cable
•Pointer Card with Product Warranty
•Technical Support Contacts

2 Cisco RV315W Broadband Wireless VPN Router Quick Start Guide
Welcome
Thank you for choosing the Cisco RV315W Broadband Wireless VPN
Router. The RV315W provides routing, switching, security, wireless, 3G,
Virtual Private Network (VPN), quality of service (QoS), and flow control
capabilities for small businesses.
This guide describes how to physically install your RV315W and launch
web-based Configuration Utility to configure and manage your RV315W.
Before You Begin
Installation Requirements
Before you begin the installation, make sure that you have the following:
•An active Internet account.
•RJ-45 Ethernet cables (Category 5E or higher) for connecting
computers, WAN and LAN interfaces, or other devices.
•PC with Microsoft Internet Explorer 6.0 (or higher) or Mozilla Firefox 3.0
(or higher) for using web-based Configuration Utility.
•(Optional) Tools for attaching the RV315W to the wall. Instructions are
provided for wall-mounting, but the wall-mounting hardware is
user-supplied.
Default Settings
These are the default settings used when configuring your RV315W for the
first time:
NOTE Press and hold the RESET button for more than 5 seconds with a
paper clip or a pencil tip to reboot the unit and restore the factory
defaults. Changes that you have previously made to the RV315W
settings are lost.
Parameter Default Value
Username cisco
Password cisco
LAN IP 192.168.1.1
DHCP Range 192.168.1.100 to 192.168.1.200
1

Cisco RV315W Broadband Wireless VPN Router Quick Start Guide 3
RV315W Features
Front Panel
POWER •Solid green when the RV315W is powered on and is
operating normally.
•Off when the RV315W is powered off or the power has
problems.
SYS •Solid green when the RV315W is connected to the
Internet through your cable or DSL modem.
•Flashes green when the RV315W is attempting to
connect to the Internet, the RV315W cannot connect to
the Internet, or the system is upgrading the firmware.
•Solid red when the system has problems.
•Flashes red when the system is overloaded, such as the
CPU utilization or the memory utilization exceeds the
limitation.
•Off when there is no Internet connection.
WAN0 •Solid green when the RV315W is connected to the
Internet through the WAN0 port, but there is no traffic
over this port.
•Flashes green when the RV315W is sending or
receiving data over the WAN0 port.
•Off when the WAN0 port has no connection.
2

4 Cisco RV315W Broadband Wireless VPN Router Quick Start Guide
WAN1 If the WAN1/LAN0 port on the back panel is set to a
secondary WAN interface (WAN1):
•Solid green when the RV315W is connected to the
Internet through the WAN1 port, but there is no traffic
over this port.
•Flashes green when the RV315W is sending or
receiving data over the WAN1 port.
•Off when the WAN1 port has no connection.
LAN0 If the WAN1/LAN0 port on the back panel is set to an
additional LAN interface (LAN0):
•Solid green when the RV315W is connected to a device
through the LAN0 port, but there is no traffic over this
port.
•Flashes green when the RV315W is sending or
receiving data over the LAN0 port.
•Off when the LAN0 port has no connection.
LAN1-8 The numbered lights correspond to the LAN ports on the
back panel of the RV315W.
•Solid green when the RV315W is connected to a device
through the corresponding port (LAN1 to 8), but there is
no traffic over that port.
•Flashes green when the RV315W is sending or
receiving data over the corresponding LAN port.
•Off when the corresponding LAN port has no
connection.
USB •Solid green when a USB device is detected, but has no
read and write operations.
•Flashes green when a USB device is detected and has
read and write operations.
•Off when the RV315W does not detect a USB device.
3G •Solid green when the RV315W is connected to a 3G
wireless network, but there is no traffic over the 3G USB
port.
•Flashes green when the RV315W is sending or
receiving data over the 3G USB port.
•Off when the RV315W does not connect to a 3G
wireless network.

Cisco RV315W Broadband Wireless VPN Router Quick Start Guide 5
WLAN •Solid green when the wireless module is enabled, but
there is no traffic over the wireless network.
•Flashes green when the RV315W is sending or
receiving data on the wireless module.
•Off when the wireless module is disabled.
VPN •Solid green when there are active VPN tunnels.
•Flashes green once per two seconds when the
RV315W is attempting to establish a VPN tunnel, or the
attempt of establishing a new VPN tunnel fails.
•Off when there is no VPN connection.
NMS •Solid green when the RV315W is connected to an
upper-level Network Management System (NMS) but
has no operations.
•Flashes green when the RV315W is connected to an
upper-level NMS and has operations.
•Off when the RV315W does not connect to an
upper-level NMS.

6 Cisco RV315W Broadband Wireless VPN Router Quick Start Guide
Back Panel
3G USB
Port Insert a 3G USB dongle into this port to connect your
RV315W to a 3G wireless network. To get the list of 3G
USB dongle models supported by the RV315W, go to
www.cisco.com/go/rv315w.
WARNING 33 cm minimum when the product is operated
with a plug-in 3G USB device which has
maximum of 7 W ERP output power.
USB Port Insert a USB storage device into this port to save syslog
messages.
WAN0 Port The WAN0 (Internet) port is connected to your Internet
device, such as a cable or DSL modem.
WAN1/
LAN0 Port
The WAN1/LAN0 port can be set to a secondary WAN
interface (WAN1) or an additional LAN interface (LAN0).
LAN1-8
Ports
These ports provide a LAN connection to network devices,
such as PCs, print servers, or switches.
RESET The RESET button has two functions:
•Reboot:Press the RESET button for at least 1, but no
more than 5 seconds with a paper clip or a pencil tip to
reboot the unit.
•RestoretoFactoryDefaults:Press and hold the
RESET button for more than 5 seconds to reboot the unit
and restore to factory defaults. Changes that you have
previously made to the RV315W settings are lost.

Cisco RV315W Broadband Wireless VPN Router Quick Start Guide 7
Mounting the RV315W
You can place your RV315W on a desktop or mount it on a wall.
Placement Tips
• Ambient Temperature—To prevent the RV315W from overheating, do
not operate it in an area that exceeds an ambient temperature of 104°F
(40°C).
•AirFlow—Be sure that there is adequate air flow around the RV315W.
• Mechanical Loading—Be sure that the RV315W is level and stable to
avoid any hazardous conditions.
Place the RV315W horizontally on a flat surface so that it sits on its four
rubber feet.
Wall Mounting
The RV315W can be wall-mounted. The wall-mounting hardware is
user-supplied. The ports on the back panel must face either upward or
downward when mounting the RV315W to the wall. The recommended
dimensions for the mount kit are as follows:
WARNING Insecure mounting might damage the device or cause injury.
Cisco is not responsible for damages incurred by insecure
wall-mounting.
POWER
(12VDC)
The POWER port is where you connect the supplied power
adapter (12 V/3 A).
Power
Switch
Powers the unit on or off.
18 mm/0.31 in 225 mm/0.98 in 36.5 mm/0.26 in 417.9 mm/0.7 in
3
1
2
4
3
196243

8 Cisco RV315W Broadband Wireless VPN Router Quick Start Guide
To mount the RV315W to the wall:
STEP 1Determine where you want to mount the RV315W. Verify that the
surface is smooth, flat, dry, and sturdy.
STEP 2Drill two pilot holes into the surface 5.9 inches (150 mm) apart.
STEP 3Insert a screw into each hole, leaving a gap between the surface
and the base of the screw head of at least 0.1 inches (3 mm).
STEP 4Place the RV315W wall-mount slots over the screws and slide the
RV315W down until the screws fit snugly into the wall-mount slots.
Connecting the RV315W
NOTE The wireless module of the RV315W is enabled by default. You can
connect one PC with an Ethernet cable or through a wireless connection
to perform the initial configuration. Use the default wireless network
name (SSID) and pre-shared key that are provided on the product label
at the bottom of the RV315W to connect the PC to your wireless network
for the first time.
STEP 1Power off all equipment, including the cable or DSL modem, the PC
that you will use to connect to the RV315W, and the RV315W.
STEP 2Connect one end of an Ethernet cable to your cable or DSL
modem. Connect the other end to the WAN0 port on the back
panel of the RV315W.
STEP 3Connect one end of a different Ethernet cable to one of the LAN
ports on the back panel. Connect the other end to an Ethernet port
on the PC that you will use to run web-based Configuration Utility.
NOTE Skip this step if you want to connect the PC to the RV315W
through a wireless connection.
STEP 4Connect the supplied power adapter to the POWER port on the
back panel. Plug the other end of the power adapter into an
electrical outlet. Make sure that the power switch is turned off.
CAUTION Use only the power adapter that is supplied with the unit.
Using a different power adapter could damage the unit.
STEP 5Power on all connected devices including the cable or DSL
modem and the PC and wait until the connections are active.
4

Cisco RV315W Broadband Wireless VPN Router Quick Start Guide 9
STEP 6Power on the RV315W.
STEP 7To connect the PC to your wireless network for the first time, you
can configure the wireless connection using the default SSID name
and pre-shared key that are provided on the product label.
A sample configuration is illustrated here.
Getting Started with the Configuration
Before you begin to use web-based Configuration Utility, make sure that
you have a PC with Internet Explorer 6.0 (or later) or Firefox 3.0 (or later).
To log in to the utility and launch the Setup Wizard to complete the initial
configuration:
STEP 1Connect a PC to an available LAN port of the RV315W. After you
power on the PC, your PC will become a DHCP client of the
RV315W and will receive an IP address in the 192.168.1.xxx range.
STEP 2Start a web browser. In the address bar, enter the default IP
address of the RV315W: 192.168.1.1.
STEP 3When the login page appears, choose the language that you prefer
to use in the utility and enter the username and password.
The default username is cisco. The default password is cisco. Both
usernames and passwords are case sensitive.
STEP 4Click Login. The Change Password page opens.
Power
Supply
Internet
Access
Devices Network
Devices
Wireless
Devices
5

10 Cisco RV315W Broadband Wireless VPN Router Quick Start Guide
For security purposes, change the password from its default
settings at your first login to prevent unauthorized access.
STEP 5Enter the old password.
STEP 6Enter the new password. Passwords should contain at least three
of these character classes: uppercase letters, lowercase letters,
digits, and special characters. Passwords must be at least eight
characters in length.
STEP 7Enter the new password again to confirm and click Save. You are
required to log in to the utility again with the new password.
STEP 8Go to the Setup Wizard page and follow the on-screen prompts to
complete the initial configuration.
After the initial configuration is complete, you can configure other
advanced features. See the help pages or the
Cisco RV315W
Broadband Wireless VPN Router Administration Guide
for more
information.