Cisco ASR-920-24SZ-IM Manual

Cisco ASR-920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M
Aggregation Services Router Hardware Installation Guide
First Published: 2016-07-04
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]
Text Part Number:

©Cisco Systems, Inc. All rights reserved.

CONTENTS
Preface Preface ix
Document Revision History ix
Document Audience x
Document Organization x
Document Conventions x
Obtaining Documentation and Submitting a Service Request xii
CHAPTER 1 Overview 1
Cisco ASR 920 Series Routers Features 1
GigabitEthernet Copper Ports 2
GE SFP Ports 2
SFP+ Ports 2
Interface Modules 3
Gigabit Ethernet RJ45 Interface Module (A900-IMA8T) 3
10-Gigabit Ethernet XFP Interface Module (A900-IMA1X) 4
2x1 10 Gigabit Ethernet SFP+ Interface Module (A900-IMA2Z) 5
8-Port 1 Gigabit Ethernet + 1-Port 10 Gigabit Ethernet SFP+ Combination Interface Module
6
8 Port T1/E1 Interface Module (A900-IMA8D) 7
Interface Availability on Interface Modules 7
Front and Back Panel 9
Specifications 12
External Interfaces 14
Network Interfaces 14
Network Timing Interfaces 15
External Alarm Inputs 15
Management Interfaces 15
Cisco ASR-920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Aggregation Services Router Hardware Installation
Guide
iii

Power Supply and Fans 15
LED Indicators 16
PWR and STAT LEDs 16
CPU Management Port LEDs 18
SFP LEDs 18
SFP+ LEDs 18
8 T1/E1 Interface Module LEDs 19
RJ-45 LEDs 20
Power Supply Unit LEDs 20
System–Interface LED Behavior 21
Online Insertion and Removal 22
Licensing the Router 23
CHAPTER 2 Preparing for Installation 25
Safety Guidelines 25
Standard Warning Statements 25
Safety Guidelines for Personal Safety and Equipment Protection 26
Safety Precautions for Module Installation and Removal 27
Safety with Electricity 27
Power Supply Considerations 30
Preventing ESD Damage 30
Site Planning 31
General Precautions 31
Site Planning Checklist 31
Site Selection Guidelines 32
Environmental Requirements 32
Physical Characteristics 33
Air Flow Guidelines 33
Air Flow Guidelines for ETSI Rack Installation 36
Floor Loading Considerations 36
Site Power Guidelines 36
Electrical Circuit Requirements 37
Site Cabling Guidelines 37
Asynchronous Terminal Connections 38
Interference Considerations 38
Cisco ASR-920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Aggregation Services Router Hardware Installation
Guide
iv
Contents

Electromagnetic Interference 38
Radio Frequency Interference 38
Lightning and AC Power Fault Interference 38
Rack-Mounting Guidelines 39
Precautions for Rack-Mounting 39
Rack Selection Guidelines 39
Equipment Rack Guidelines 40
Locating for Safety 40
Locating for Easy Maintenance 40
Locating for Proper Airflow 41
Installation Checklist 41
Creating a Site Log 42
Receiving the Router 43
Chassis-Lifting Guidelines 44
Tools and Equipment 45
Unpacking and Verifying the Shipped Contents 45
CHAPTER 3 Installing the Router 49
Prerequisites 49
Installing the Router in a Rack 50
Installing the Chassis Brackets 50
Installing the Router Chassis in the Rack 56
Attaching the Cable Guides 59
Wall Mounting the Routers 61
Attaching the Brackets to the Router for Wall-Mounting 62
Mounting Routers on the Wall 62
Installing and Removing the Interface Module 66
Installing the Interface Module 66
Removing the Interface Module 68
Hot-Swapping the Interface Module 69
Installing and Removing the Fan Tray 70
Installing the Fan Tray 70
Removing the Fan Tray 73
Installing the Power Supply 76
Preventing Power Loss 77
Cisco ASR-920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Aggregation Services Router Hardware Installation
Guide
v
Contents

Power Connection Guidelines 77
Guidelines for DC-Powered Systems 78
Guidelines for AC-Powered Systems 78
Installing a DC Power Supply 78
Installing a DC Power Supply Module 79
Attaching Cables to the DC Power Supply 80
Powering On the Router 82
Removing and Replacing a DC Power Supply 82
Installing an AC power Supply 84
Installing an AC Power Supply Module 85
Activating an AC Power Supply 86
Removing and Replacing an AC Power Supply 89
Installing and Removing SFP Modules 90
Installing SFP Modules 91
Removing SFP Modules 94
Connecting to the 10/100/1000 Ports 96
Connecting to SFP Modules 97
Connecting to Fiber-Optic SFP Modules 97
Installing the Chassis Ground Connection 98
Power Connection Guidelines 100
Guidelines for DC-Powered Systems 101
Guidelines for AC-Powered Systems 101
Preventing Power Loss 101
Activating a DC Power Supply 102
Activating an AC Power Supply 102
Connecting a Router to the Network 103
Connecting Console Cables 103
Connecting to the USB Serial Port Using Microsoft Windows 103
Connecting to the Console Port Using Mac OS X 105
Connecting to the Console Port Using Linux 106
Installing the Cisco USB Device Driver 106
Uninstalling the Cisco USB Device Driver 107
Connecting to the EIA Console Port 108
Connecting a Management Ethernet Cable 110
Installing and Removing SFP and SFP+ Modules 110
Cisco ASR-920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Aggregation Services Router Hardware Installation
Guide
vi
Contents

Connecting a USB Flash Device 110
Removing a USB Flash Device 111
Connecting Timing Cables 111
Connecting a Cable to the BITS Interface 111
Connecting Cables to the GPS Interface 112
Connecting a Cable to the Input 10-Mhz or 1-PPS Interface 112
Connecting a Cable to the Output 10-Mhz or 1-PPS Interface 113
Connecting a Cable to the ToD Interface 113
Connecting Ethernet Cables 114
Connecting Cables to SFP Modules 115
Connector and Cable Specifications 115
CHAPTER 4 Initial Configuration 117
Checking Conditions Prior to System Startup 117
Powering Up the Router 118
Verifying the Front Panel LEDs 121
Verifying the Hardware Configuration 121
Checking Hardware and Software Compatibility 122
Configuring the Router at Startup 122
Accessing the CLI Using the Console 122
Configuring Global Parameters 124
Checking the Running Configuration Settings 125
Saving the Running Configuration to NVRAM 125
Safely Powering Off the Router 125
Automatic Shutdown of the Router 126
CHAPTER 5 Troubleshooting 127
Pinouts 127
BITS Port Pinouts 127
GPS Port Pinout 128
Time-of-Day Port Pinouts 128
Alarm Port Pinouts 129
Management Ethernet Port Pinouts 130
USB Console Port Pinouts 130
USB Flash or MEM Port Pinouts 131
Cisco ASR-920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Aggregation Services Router Hardware Installation
Guide
vii
Contents

RJ45C Port Pinouts 131
Optical Fiber Specifications 132
Alarm Conditions 132
CHAPTER 6 Site Log 133
CHAPTER 7 Supported PIDs 135
Cisco ASR-920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Aggregation Services Router Hardware Installation
Guide
viii
Contents

Preface
The preface describes the revision history, audience, organization, and conventions of the Cisco ASR 920
Series Aggregation Services Routers. It also lists sources for obtaining additional information and technical
assistance from Cisco.
This document covers the following variants of the Cisco ASR 920 Series Aggregation Services Routers:
•ASR-920-24SZ-IM—Twenty Four 1GE Fiber ports, Four 10G ports, and One slot for modular interface
card, with replaceable redundant AC and DC power supplies
•ASR-920-24SZ-M—Twenty Four 1GE Fiber ports and Four 10G ports, with replaceable redundant
AC and DC power supplies
•ASR-920-24TZ-M—Twenty Four 1 GE Copper ports and Four 10G ports, with replaceable redundant
AC and DC power supplies
•Document Revision History, page ix
•Document Audience, page x
•Document Organization, page x
•Document Conventions, page x
•Obtaining Documentation and Submitting a Service Request, page xii
Document Revision History
The following table lists the major changes made to this document.
Change SummaryDateRelease
First ReleaseNovember 22, 2014Cisco IOS XE Release 3.14.0S
Cisco ASR-920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Aggregation Services Router Hardware Installation
Guide
ix

Document Audience
This guide is intended for users who are responsible for installing the Cisco ASR 920-24SZ-IM,
ASR-920-24SZ-M, ASR-920-24TZ-M Router. It is intended for users who may not be familiar with the initial
configuration and troubleshooting tasks, the relationship among tasks, or the Cisco IOS software commands
necessary to perform particular tasks.
Document Organization
This guide includes the following chapters and appendix:
DescriptionTitle
Describes the features and specifications of the Cisco
ASR 920 Series Aggregation Services Routers.
Overview, on page 1
Describes the installation of the Cisco ASR
920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M
Router at your site.
Preparing for Installation, on page 25
Describes the installation of router on a rack as well
as installation of its components.
Installing the Router, on page 49
Describes basic router configuration.Initial Configuration, on page 117
Describes troubleshooting information.Troubleshooting, on page 127
Provides a record of actions related to installing and
maintaining the router.
Site Log, on page 133
Describes the supported SFPs.Supported PIDs, on page 135
Document Conventions
This document uses the following conventions:
IndicationConvention
Commands and keywords and user-entered text
appear in bold font.
bold font
Document titles, new or emphasized terms, and
arguments for which you supply values are in italic
font.
italic font
Elements in square brackets are optional.[ ]
Cisco ASR-920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Aggregation Services Router Hardware Installation
Guide
x
Preface
Document Audience

IndicationConvention
Required alternative keywords are grouped in braces
and separated by vertical bars.
{x | y | z }
Optional alternative keywords are grouped in brackets
and separated by vertical bars.
[ x | y | z ]
A nonquoted set of characters. Do not use quotation
marks around the string or the string will include the
quotation marks.
string
Terminal sessions and information the system displays
appear in courier font.
courier font
Nonprinting characters such as passwords are in angle
brackets.
< >
Default responses to system prompts are in square
brackets.
[ ]
An exclamation point (!) or a pound sign (#) at the
beginning of a line of code indicates a comment line.
!, #
Means reader take note. Notes contain helpful suggestions or references to material not covered in the
manual.
Note
Means the following information will help you solve a problem. The tips information might not be
troubleshooting or even an action, but could be useful information, similar to a Timesaver.
Tip
Means reader be careful. In this situation, you might perform an action that could result in equipment
damage or loss of data.
Caution
Means the described action saves time. You can save time by performing the action described in the
paragraph.
Timesaver
Means reader be warned. In this situation, you might perform an action that could result in bodily injury.
Warning
Cisco ASR-920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Aggregation Services Router Hardware Installation
Guide
xi
Preface
Document Conventions

IMPORTANT SAFETY INSTRUCTIONS.
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with
standard practices for preventing accidents. Use the statement number provided at the end of each warning
to locate its translation in the translated safety warnings that accompanied this device.
SAVE THESE INSTRUCTIONS
Warning
Statements using this symbol are provided for additional information and to comply with regulatory and
customer requirements.
Warning
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information,
see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco
technical documentation.
Subscribe to the What’s New in Cisco Product Documentation, which lists all new and revised Cisco technical
documentation as an RSS feed and delivers content directly to your desktop using a reader application. The
RSS feeds are a free service.
Cisco ASR-920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Aggregation Services Router Hardware Installation
Guide
xii
Preface
Obtaining Documentation and Submitting a Service Request

CHAPTER 1
Overview
The Cisco ASR 920 Series Aggregation Services Router is a family of modular and fixed configuration
routers that enables Service Providers to provide business, residential, and mobile access services to their
users. It is the Carrier Ethernet access platform providing Ethernet services.
The Cisco ASR 920 Series Routers family complement and extend Cisco’s current and planned Carrier
Ethernet routing portfolio providing a cost optimized, and extended temperature range access platform.
•Cisco ASR 920 Series Routers Features, page 1
Cisco ASR 920 Series Routers Features
The Cisco ASR 920 Series Routers family includes:
•ASR 920-Modular [ASR-920-24SZ-IM]—This sub-family with 1.5 RU form factor has fixed ENET
interfaces (four 10GE and twenty-four 1GE Fiber), one slot for modular interface card and redundant
modular power supplies (AC/DC). The interface modules from ASR 900 family of routers can be
leveraged for use with this model.
•ASR 920-Fixed [ASR-920-24SZ-M/ASR-920-24TZ-M]—This sub-family with 1 RU form factor has
fixed ENET interfaces (four 10GE and twenty-four 1GE Copper or SFP) and redundant modular power
supplies (AC/DC).
The following table provides a snapshot of the number and type of supported ports:
Table 1: Supported Ports on Cisco ASR 920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Router
Timing PortsType of 10 GE PortType of 1 GE Port10 GE Port1 GE PortASR 920 Sub-family
ToD and BITSGPS
1 PPS and GPS 10
MHz
Built in 4 SFP+24 Fiber424ASR-920-24SZ-IM
NABuilt in 4 SFP+24 Fiber 24 Copper424ASR-920-24SZ-M/ASR-920-24TZ-M
Cisco ASR-920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Aggregation Services Router Hardware Installation
Guide
1

GigabitEthernet Copper Ports
Fixed copper GigabitEthernet (GE) interfaces are provided through standard RJ-45 connectors. These ports
support the following features:
•Standard 10/100/1000Base-T/TX operation with forced or auto-negotiation for speed and duplex.
•Automatic crossover (auto-MDIX) for straight-through and crossover connections.
•Pause flow control as defined by the 802.3x standard.
•Frame size of 9216 bytes.
•Synchronous ENET operation that provides its recovered receive clock as an input clock source for the
SETS as well as uses the system-wide reference clock to derive its transmit clock.
GE SFP Ports
The GE SFP ports support the following features:
•100Base-FX and 1000Base-X SFP modules.
•Copper SFP modules
•Digital optical monitoring as specified by the SFP.
•Any mix of SFPs is supported unless specifically noted.
•Pause flow control as defined by the 802.3x standard.
•Frame size of 9216 bytes.
•Synchronous ENET operation that provides its recovered receive clock as an input clock source for the
SETS as well as uses the system-wide reference clock to derive its transmit clock.
Copper based SFPs do not support synchronous ENET operations.Note
SFP+ Ports
The SFP+ ports support the following features:
•Digital optical monitoring as specified by the optical transceiver module.
•Any mix of SFPs is supported unless specifically noted.
•Pause flow control as defined by the 802.3x standard.
•Frame size of 9216 bytes.
Cisco ASR-920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Aggregation Services Router Hardware Installation
Guide
2
Overview
GigabitEthernet Copper Ports

Interface Modules
The Cisco ASR-920-24SZ-IM Router interface modules are field-replaceable units. In addition to the ports
provided on an RSP, the Cisco ASR-920-24SZ-IM Router supports the interface modules.
Gigabit Ethernet RJ45 Interface Module (A900-IMA8T)
The Gigabit Ethernet RJ45 interface module provides eight Gigabit Ethernet copper ports. The figure below
shows the interface module.
Figure 1: 8 x 1-Gigabit Ethernet RJ45 (Copper) Interface Module
•For more information about installing an RJ45 Gigabit Ethernet module, see the Installing the Interface
Module section.
•To determine interfaces available on the RJ45 Gigabit Ethernet module, see the Interface Availability
on Interface Modules section.
Cisco ASR-920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Aggregation Services Router Hardware Installation
Guide
3
Overview
Interface Modules

10-Gigabit Ethernet XFP Interface Module (A900-IMA1X)
The 10-Gigabit Ethernet XFP interface module provides a single port supporting a 10-Gigabit Ethernet XFP
module. The following figure shows the interface module.
Figure 2: 1 x 10-Gigabit Ethernet XFP Interface Module
•For more information about installing a 10-Gigabit Ethernet XFP module, see the Installing the Interface
Module section.
•To determine interfaces available on the 10-Gigabit Ethernet XFP module, see the Interface Availability
on Interface Modules section.
•For information on supported SFPs, see the Cisco ASR 900 Series Aggregation Services Router Interface
Modules Data Sheet at http://www.cisco.com/c/en/us/products/routers/
asr-903-series-aggregation-services-routers/datasheet-listing.html.
Cisco ASR-920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Aggregation Services Router Hardware Installation
Guide
4
Overview
Interface Modules

2x1 10 Gigabit Ethernet SFP+ Interface Module (A900-IMA2Z)
The 2-port 10-Gigabit Ethernet interface module provides a dual port supporting a 10-Gigabit Ethernet SFP+
and XFP module.
Figure 3: 2X10 Gigabit Ethernet Interface Module
•For more information about installing the 2X10 GE SFP Gigabit Ethernet module, see the Installing the
Interface Module section.
•To determine interfaces available on the 2X10 GE SFP Gigabit Ethernet module, see the Interface
Availability on Interface Modules section.
•For information on supported SFPs, see the Cisco ASR 900 Series Aggregation Services Router Interface
Modules Data Sheet at http://www.cisco.com/c/en/us/products/routers/
asr-903-series-aggregation-services-routers/datasheet-listing.html.
Cisco ASR-920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Aggregation Services Router Hardware Installation
Guide
5
Overview
Interface Modules

8-Port 1 Gigabit Ethernet + 1-Port 10 Gigabit Ethernet SFP+ Combination Interface Module
This 8-port 1 Gigabit Ethernet (RJ45 Copper) interface module with the 1-port 10 Gigabit Ethernet interface
module is a high density combination interface module. This module supports 8 Gigabit Ethernet Copper
ports and 1 10 Gigabit Ethernet SFP+ port.
Figure 4: 8-port 1 GE (RJ45) + 1-port 10 GE SFP+ Interface Module
Cisco ASR-920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Aggregation Services Router Hardware Installation
Guide
6
Overview
Interface Modules

8 Port T1/E1 Interface Module (A900-IMA8D)
The 8T1/E1 interface module provides connectivity for up to 8 x T1/E1 ports through RJ48C connectors on
the front panel. The following figure shows the interface module.
Figure 5: 8 x T1/E1 Interface Module
•For more information about installing a 8 Port T1/E1 interface module, see the Installing the Interface
Module section.
•To determine interfaces available on the 8 Port T1/E1 interface module, see the Interface Availability
on Interface Modules section.
•For LED indicator information on the 8 Port T1/E1 interface module, see the 8 T1/E1 Interface Module
LEDs section.
•For RJ45C pinout information on the 8 Port T1/E1 interface module, see the RJ45C Port Pinouts section.
Interface Availability on Interface Modules
Cisco ASR-920-24SZ-IM Router does not support over-subscription mode. You must disable the ports
as appropriate to restrict the system usage to 64 Gbps. Enabling all the interfaces in over-subscription
mode can result in an unpredictable system performance.
Note
The following table provides a snapshot of the interfaces available on supported interface modules:
Cisco ASR-920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Aggregation Services Router Hardware Installation
Guide
7
Overview
Interface Modules

Table 2: Interface Availability on Supported Interface Modules
Front Panel
Ports
Disabled
System
Oversubscribed
Interfaces
in
Resulting
System
QuantityInterface
Module
DS3/E3OC3/OC12T1/E110GESFPCu
00042400None
16 to 23No00041681A900-IMA8T
Yes00062401A900-IMA2Z
Yes00052401A900-IMA1X
20 to 23No00842001A900-IMA8D
Cisco ASR-920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Aggregation Services Router Hardware Installation
Guide
8
Overview
Interface Modules