Cisco 3825 - Voice Bundle Router Operating instructions

1
Troubleshooting Cisco 3800 Series Routers
OL-5972-01
Troubleshooting Cisco 3800 Series Routers
Your Cisco 3800 series integrated services router goes through extensive testing and burn-in before
leaving the factory. If you encounter problems, use this document to help isolate problems or to eliminate
the router as the source of the problem.
This document contains the following sections:
•Solving Problems, page 2
•LEDs, page 5
•The show environment Command, page 9
•Error Messages, page 10
•Jumper Settings, page 12
•Recovering a Lost Password, page 13
•More Troubleshooting Help, page 13
Note To troubleshoot network modules, see the Cisco Network Modules Hardware Installation Guide. To
troubleshoot interface cards, see the Cisco Interface Cards Installation Guide. These documents are
available on Cisco.com.
If you cannot find the source of the problem, contact a customer service representative. For information
about obtaining technical support, see the “Obtaining Technical Assistance” section on page 12 of
“Introduction to Cisco 3800 Series Routers Hardware Documentation.” Before you call, have the
following information ready:
•Router type and serial number (for serial number locations, see the “Product Identification” section
on page 5 of “Overview of Cisco 3800 Series Routers”)
•Maintenance agreement or warranty information
•Type of software and version number
•Date you received the router
•Brief description of the problem
•Brief explanation of the steps taken to isolate the problem

Solving Problems
2
Troubleshooting Cisco 3800 Series Routers OL-5972-01
Solving Problems
The key to solving problems is to isolate the problem to a specific subsystem by comparing what the
router is doing to what it should be doing.
The LEDs on the front and rear panel of the router enable you to determine router performance and
operation. LEDs are described in the “LEDs” section on page 5.
When solving problems, consider the following subsystems:
•Power and cooling systems—External power source, power cable, router power supply and circuit
breaker, and router blower and fan. Also consider inadequate ventilation or air circulation.
•Network modules and interface cards—LEDs on the modules and interface cards help identify a
failure.
•Cables—External cables that connect the router to the network.
Troubleshooting the Power and Cooling Systems
Both the system power LED and the fans can help you troubleshoot a power problem. Check the
following items.
Note The Cisco 3845 router has two system power LEDs, one for each power supply, labeled SYS PWR1 and
SYS PWR2.
Normal Indications
With the power switch on, normal indications are:
•SYS LED steady green
•SYS PWR LED steady green for the Cisco 3825 router, or SYS PWR1 or SYS PWR2 LED steady
green for the Cisco 3845 router (depending on which power supply is active)
•Fans operating
Fault Indications
Check the following symptoms to locate or eliminate faults in the power and cooling systems:
•With the power switch on, what color is the SYS LED?
– If the LED is steady green, the router is receiving power and is functional.
– If the LED is amber, the router is receiving power but is not functional.
– If the LED is off, check the power source and power cable.
•With the power switch on, the SYS LED steady green, and the SYS PWR LED (Cisco 3825) or
SYS PWR1 or SYS PWR2 LED (Cisco 3845) steady green, do the fans operate?
– If yes, the power system is functioning.
– If no, check the fans.

Solving Problems
3
Troubleshooting Cisco 3800 Series Routers
OL-5972-01
•With the power switch on and the SYS LED steady green, do the fans operate?
– If yes, the power system is functioning.
– If no, check the fans.
•With the power switch on and the SYS PWR LED (Cisco 3825) or SYS PWR1 or SYS PWR2 LED
(Cisco 3845) off, do the fans operate?
– If yes, the router is receiving power. The fans are connected directly to the DC outputs of the
power supply.
– If no, check the power source and power cable.
•Does the router shut down after being on a short time?
– Check for an environmentally induced shutdown. See the next section, “Environmental
Reporting Features.”
– Check the environmental site requirements in the “General Site Requirements” section on
page 3 of “Preinstallation Requirements and Planning for Cisco 3800 Series Routers.”
– Check for a power supply failure by inspecting the SYS PWR LED on the Cisco 3825 router,
or the SYS PWR1 or SYS PWR2 LED on the Cisco 3845 router (depending on which power
supply is active). If the LED is green, the power supply is functional.
•Router partially boots, but LEDs do not come on.
– Check for a power supply failure by inspecting the SYS PWR LED on the Cisco 3825 router or
the SYS PWR1 LED or SYS PWR2 LED on the Cisco 3845 router (depending on which power
supply is active). If the LED is green, the power supply is functional.
– If the SYS PWR LED is not on, see the “Obtaining Technical Assistance” section on page 12
of “Introduction to Cisco 3800 Series Routers Hardware Documentation” for information about
customer service. For warranty information, see the “Cisco 90-Day Limited Hardware Warranty
Terms” section on page 10 of “Introduction to Cisco 3800 Series Routers Hardware
Documentation.”
Environmental Reporting Features
If the router is operating at an abnormally high temperature, the following message is displayed on the
console screen:
System detected OVERTEMPERATURE condition. Please resolve cooling problem immediately!
Some causes of abnormally high router temperature are:
•Fan failure
•Air conditioning failure in the room
•Air blockage to cooling vents
Take steps to correct the problem. See also the “Site Environment” section on page 4 and the “Equipment
Racks” section on page 5 of “Preinstallation Requirements and Planning for Cisco 3800 Series Routers.”

Solving Problems
4
Troubleshooting Cisco 3800 Series Routers OL-5972-01
Troubleshooting Modules, Cables, and Connections
Network problems can be caused by a module; cables or cable connections; or external devices such as
a modem, transceiver, hub, wall jack, WAN interface, or terminal. Check for the following symptoms to
help isolate the problem:
•Network module or interface card is not recognized by the router.
– Make sure that the module or interface card is firmly seated in its slot.
– Check the LEDs on the module or interface card. For information on these LEDs, see the Cisco
Network Modules Hardware Installation Guide and the Cisco Interface Cards Installation
Guide.
– Make sure that you have a version of Cisco IOS software that supports the network module or
interface card. To determine which Cisco IOS releases support your router, network modules,
and interface cards, go to the Software Advisor at http://tools.cisco.com/Support/Fusion/.You
must have an account on Cisco.com.
•Module or card is recognized, but interface ports do not initialize.
– Make sure that the module or card is firmly seated in its slot.
– Check external cable connections.
– Make sure that you have a version of Cisco IOS software that supports network module or
interface card. To determine which Cisco IOS releases support your router, network modules,
and interface cards, go to the Software Advisor at http://tools.cisco.com/Support/Fusion/.You
must have an account on Cisco.com.
•Router does not boot properly, or constantly or intermittently reboots.
– Make sure that all modules are firmly seated in their slots.
– Check the router chassis or software. For information about customer service, see the
“Obtaining Technical Assistance” section on page 12 of “Introduction to Cisco 3800 Series
Routers Hardware Documentation.” For warranty information, see the “Cisco 90-Day Limited
Hardware Warranty Terms” section on page 10 of “Introduction to Cisco 3800 Series Routers
Hardware Documentation.”
•Router boots, but the console screen is frozen.
– Check the external console connection.
– Verify that the parameters for your terminal are set as follows:
-The data rate matches the one configured for the router (9600 bps is the default)
-8 data bits
-No parity
-1 stop bit
•Router powers on and boots only when a particular network module or interface card is removed.
– Check the network module or interface card. For information about customer service, see the
“Obtaining Technical Assistance” section on page 12 of “Introduction to Cisco 3800 Series
Routers Hardware Documentation.” For warranty information, see the “Cisco 90-Day Limited
Hardware Warranty Terms” section on page 10 of “Introduction to Cisco 3800 Series Routers
Hardware Documentation.”

LEDs
5
Troubleshooting Cisco 3800 Series Routers
OL-5972-01
•Router powers on and boots only when a particular cable is disconnected.
– There may be a problem with the module, interface card, or cable. For information about
customer service, see the “Obtaining Technical Assistance” section on page 12 of “Introduction
to Cisco 3800 Series Routers Hardware Documentation.” For warranty information, see the
“Cisco 90-Day Limited Hardware Warranty Terms” section on page 10 of “Introduction to
Cisco 3800 Series Routers Hardware Documentation.”
LEDs
LEDs enable you to determine router performance and operation. Figure 1 and Figure 2 show the LEDs
on the Cisco 3825 router. Figure 3 and Figure 4 show the LEDs on the Cisco 3845 router. Each power
supply in a Cisco 3845 router also has its own LED.
For an explanation of these LEDs, see Table 1.
Figure 1 Cisco 3825 Front-Panel LEDs
117780
0
1
COMPACT FLASH
SYS AUX ACT RPS IP PWR AIM0 AIM1 PVDM0 PVDM1 PVDM2 PVDM3
R
SYS
ACT
SYS
PWR
RPS
AUX
PWR
AIM0
AIM1 PVDM0 PVDM1 PVDM2 PVDM3

LEDs
6
Troubleshooting Cisco 3800 Series Routers OL-5972-01
Figure 2 Cisco 3825 Rear-Panel LEDs
Figure 3 Cisco 3845 Front-Panel LEDs
117782
EN
NMD-
ESW-
36
23x 5x
FastEthernet Ports
22x 4x 21x 3x 20x 2x 19x 1x 18x 0x
29x 11x 28x 10x 27x 9x 26x 8x 25x 17 24x 6x
35x 17x 34x 16x 33x 15x 32x 14x 31x 13x 30x 12x
Ext
Pwr
-48V
0x
18x
GE0
10/100/
1000
Base-Tx
35x
10/100/1000
Base-Tx
GE1
17x
EN
NM-
ESW-
16
15x 7x 14x 6x 13x 5x
FastEthernet Ports
12x 4x 11x 3x 10x 2x 9x 1x 8x 0x
Ext
Pwr
-48V
0x
8x
7x
15x
GE
10/100/
1000
Base-Tx
AUX
CONSOLE
GE 0/0 GE 0/0
GE 1/0
SPD LNK SFP
SPD LNK
117781

LEDs
7
Troubleshooting Cisco 3800 Series Routers
OL-5972-01
Figure 4 Cisco 3845 Router Rear-Panel LEDs
Table 1 Cisco 3800 Series LED Indicators
LED 3825 3845 Color and State Meaning
SYS Front Front Off Router not receiving power
Steady green Normal operation (power-up complete)
Blinking green Booting or in ROM monitor mode (immediately
after power-up)
Amber Powered but malfunctioning
ACT Front Front Off No packet activity
Steady or
blinking green Packets transmitted or received on any WAN or LAN port, or router is monitoring internal
activities (power-up completed)
SYS PWR Front — Off Router not receiving power
Steady green Normal operation (immediately after power-up)
RPS Front — Off Connected to primary power system
Steady green Connected to redundant power system
SYS PWR1 — Front Off Router not receiving power, power supply 1 not
present, or power-up not completed
Steady green Present and enabled (power-up completed)
Amber Present and off or malfunctioning
SYS PWR2 — Front Off Router not receiving power, power supply 2 not
present, or power-up not completed
Steady green Present and enabled (power-up completed)
Amber Present and off or malfunctioning
117783
CONSOLE
CF
AIM 1
PVDM 3 AIM 0
PVDM 0PVDM 1PVDM 2
SFP
SPD
SPD
LNK
LNK
AUX GigE 0/0
GigE 0/1
PVDM 3
CF
PVDM 2 PVDM 1 PVDM 0 AIM 1 AIM 0
SFP
GigE 0/1
SPD
SPD
LNK
LNK
GigE 0/0

LEDs
8
Troubleshooting Cisco 3800 Series Routers OL-5972-01
AUX PWR Front — Off IP phone power off or not present, or power-up
not completed
Steady green Present and enabled (power-up completed)
Amber Powered but malfunctioning
AUX PWR1 — Front Off IP phone power supply 1 off or not present, or
power-up not completed
Steady green Present and enabled (power-up completed)
Amber Powered but malfunctioning
AUX PWR2 — Front Off IP phone power supply 2 off or not present, or
power-up not completed
Steady green Present and enabled (power-up completed)
Amber Powered but malfunctioning
AIM0 Front Rear Off AIM0 not present
Green Present and enabled
Amber Present but malfunctioning
AIM1 Front Rear Off AIM1 not present
Green Present and enabled
Amber Present but malfunctioning
PVDM0 Front Rear Off PVDM0 not present
Green Present and enabled
Amber Present but malfunctioning
PVDM1 Front Rear Off PVDM1 not present
Green Present and enabled
Amber Present but malfunctioning
PVDM2 Front Rear Off PVDM2 not present
Green Present and enabled
Amber Present but malfunctioning
PVDM3 Front Rear Off PVDM3 not present
Green Present and enabled
Amber Present but malfunctioning
CF Front Rear Off CompactFlash memory card not being accessed
Steady green CompactFlash card being accessed; do not eject
Blinking green CompactFlash card being accessed; do not eject
SFP Rear Rear Off SFP link not established
Green SFP port active, link established
GE0: Link Rear Rear Off No link
Green Ethernet cable present, link established
Table 1 Cisco 3800 Series LED Indicators (continued)
LED 3825 3845 Color and State Meaning

The show environment Command
9
Troubleshooting Cisco 3800 Series Routers
OL-5972-01
The show environment Command
The show environment command can help you monitor and troubleshoot router power and ventilation
status.
This is an example of the output of the show environment command for a Cisco 3825 router with an AC
power supply and no Redundant Power System:
Router# show environment
Redundant Power System is not present.
SYS PS1 is present.
Type: AC
AUX (-48V) PS1 is absent.
Fan 1 Normal
Fan 2 Normal
Fan 3 Normal
Fan Speed is Normal
Alert settings:
Intake temperature warning: Enabled, Threshold: 50
Core temperature warning: Enabled, Threshold: 70 (CPU: 95)
Board Temperature: Normal
Internal-ambient temperature = 29, Normal
CPU temperature = 46, Normal
Intake temperature = 31, Normal
Voltage 1(3300) is Normal, Current voltage = 3316 mV
Voltage 2(5150) is Normal, Current voltage = 5210 mV
Voltage 3(2500) is Normal, Current voltage = 2525 mV
Voltage 4(1200) is Normal, Current voltage = 1191 mV
GE0: Speed Rear Rear Blinking green Blink frequency indicates port speed
1 blink per second: 10 Mbps
2 blinks per second: 100 Mbps
3 blinks per second: 1000 Mbps
GE1: Link Rear Rear Off No link
Green Ethernet cable present, link established
GE1: Speed Rear Rear Blinking green Blink frequency indicates port speed
1 blink per second: 10 Mbps
2 blinks per second: 100 Mbps
3 blinks per second: 1000 Mbps
PS1 — Front Off Power supply 1 not present
Steady green Present and enabled
Amber Present and off or malfunctioning
PS2 — Front Off Power supply 2 not present
Steady green Present and enabled
Amber Present and off or malfunctioning
Table 1 Cisco 3800 Series LED Indicators (continued)
LED 3825 3845 Color and State Meaning

Error Messages
10
Troubleshooting Cisco 3800 Series Routers OL-5972-01
This is an example of the output of the show environment command for a Cisco 3845 router that has
one AC power supply with IP phone power output installed:
Router# show environment
SYS PS1 is present
Fan status: Normal
Input Voltage status: Normal
DC Output Voltage status: Normal
Type: AC
Thermal status: Normal
SYS PS2 is absent
AUX (-48V) PS1 is present
AUX (-48V) PS2 is absent
Fan 1 Normal
Fan 2 Normal
Fan 3 Normal
Fan Speed is Normal
Alert settings:
Intake temperature warning: Enabled, Threshold: 50
Core temperature warning: Enabled, Threshold: 70 (CPU: 90)
Board Temperature: Normal
Internal-ambient temperature = 31, Normal
CPU temperature = 50, Normal
Intake temperature = 25, Normal
Backplane temperature = 24, Normal
Voltage 1(3300) is Normal, Current voltage = 3284 mV
Voltage 2(5150) is Normal, Current voltage = 5210 mV
Voltage 3(2500) is Normal, Current voltage = 2549 mV
Voltage 4(1200) is Normal, Current voltage = 1215 mV
Error Messages
This section describes error messages that may appear on an external console screen. (For more
information about consoles, see the “Connecting a Console or Modem” section on page 9 of
“Connecting Cables to Cisco 3800 Series Routers.”)
Cisco IOS software checks the system once every 30 seconds. If an error still exists, the error message
is displayed again; if the error has cleared, a recovery message is displayed.
Error Message System detected OVERTEMPERATURE condition. Please resolve cooling
problem immediately!
Explanation The router is operating at a temperature higher than the user-set threshold, possibly
caused by fan failure, air-conditioning failure in the room, or air blockage to cooling vents.
Recommended Action Make sure that the ambient room temperature does not exceed 40 degrees C
and that airflow to the router is not blocked. See the “Site Environment” section on page 4 and the
“Equipment Racks” section on page 5 of “Preinstallation Requirements and Planning for
Cisco 3800 Series Routers.”
If this condition persists, the power-supply thermal monitor automatically shuts down the router.
Call your Cisco technical support representative for help, if necessary.