Cisco RV130 Instruction Manual

Cisco RV130 Multifunction VPN Router
Cisco RV130W Wireless Multifunction VPN Router
ADMINISTRATION
GUIDE

Revised August 2014
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL:
www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership
relationship between Cisco and any other company. (1110R)

Cisco RV130/RV130W Wireless Multifunction VPN Router Administration Guide 1
Contents
Chapter 1: Introduction 6
Verifying the Hardware Installation 6
Using the Setup Wizard 7
Configuration Next Steps 8
Using the Getting Started Page 8
Connecting to Your Wireless Network 10
Chapter 2: Viewing Device Status 12
Viewing the Dashboard 12
Viewing the System Summary 13
Viewing Active TCP/IP Services 15
Viewing Wireless Statistics 15
Viewing Captive Portal Status 15
Viewing Site-to-Site IPsec VPN Connection Status 15
Viewing the IPsec VPN Server Status 16
Viewing PPTP Server 16
Viewing Logs 16
Viewing Connected Devices 17
Viewing Port Statistics 18
Viewing the Mobile Network Status 18
Chapter 3: Configuring Networking 20
Configuring WAN Settings 21
Configuring Wired WAN Connections 21
Configuring DHCP 21
Configuring Static IP 22
Configuring PPPoE 22
Configuring PPTP 24
Configuring L2TP 26
Configuring Optional Settings 28
Configuring a Mobile Network 30
Configuring Global Mobile Network Settings 30

Cisco RV130/RV130W Wireless Multifunction VPN Router Administration Guide 2
Contents
Configuring Mobile Network Settings Manually 31
Bandwidth Cap Setting 32
E-mail Setting 32
Setting Failover and Recovery 33
Configuring LAN Settings 34
Changing the Device Management IP Address 34
Configuring DHCP Server 35
Configuring VLANs 37
Configuring Static DHCP 38
Viewing DHCP Leased Clients 39
Configuring a DMZ Host 39
Configuring RSTP 40
Port Management 41
Configuring Link Aggregation 42
Cloning the MAC Address 43
Configuring Routing 44
Configuring the Operating Mode 44
Configuring Dynamic Routing 44
Configuring Inter-VLAN Routing 45
Configuring Static Routing 45
Viewing the Routing Table 46
Configuring Dynamic DNS 47
Configuring the IP Mode 48
Configuring IPv6 49
Configuring the IPV6 WAN Connection 49
Configuring IPv6 LAN Connections 53
Configuring IPv6 Static Routing 55
Configuring Routing (RIPng) 56
Configuring Tunneling 57
Viewing IPv6 Tunnel Status 58
Configuring Router Advertisement 58
Configuring Advertisement Prefixes 60

Cisco RV130/RV130W Wireless Multifunction VPN Router Administration Guide 3
Contents
Chapter 4: Configuring Wireless Networks 63
Wireless Security 63
Wireless Security Tips 63
General Network Security Guidelines 65
Wireless Networks on Your Device 65
Configuring Basic Wireless Settings 66
Editing Wireless Network Settings 68
Configuring the Security Mode 69
Configuring MAC Filtering 72
Configuring Time of Day Access 73
Configuring Advanced Wireless Settings 74
Detecting Rogue Access Points 77
Importing Authorized AP Lists 78
Configuring WDS 80
Configuring WPS 81
Configuring Captive Portal 82
Configuring Device Mode 85
Chapter 5: Configuring the Firewall 86
Firewall Features 86
Configuring Basic Firewall Settings 87
Configuring Remote Management 90
Configuring Universal Plug and Play 91
Managing Firewall Schedules 92
Adding or Editing a Firewall Schedule 92
Configuring Services Management 92
Configuring Access Rules 93
Adding Access Rules 94
Creating an Internet Access Policy 97
Adding or Editing an Internet Access Policy 97
Configuring One-to-One Network Address Translation (NAT) 99

Cisco RV130/RV130W Wireless Multifunction VPN Router Administration Guide 4
Contents
Configuring Port Forwarding 99
Configuring Single Port Forwarding 100
Configuring Port Range Forwarding 101
Configuring Port Range Triggering 101
Chapter 6: Configuring VPN 103
VPN Tunnel Types 103
Configuring Basic Site-to-Site IPsec VPN 103
Viewing Default Values 105
Configuring Site-to-Site IPsec VPN Advanced Parameters 105
Managing IKE Policies 105
Managing VPN Policies 107
Configuring IPsec VPN Server 109
Configuring the IPsec VPN Server 109
Configuring IPsec VPN User Accounts 111
Configuring PPTP 111
Configuring the PPTP Server 112
Creating and Managing PPTP Users 112
Configuring VPN Passthrough 113
Chapter 7: Configuring Quality of Service (QoS) 114
Configuring Bandwidth Management 114
Configuring Bandwidth 115
Configuring Bandwidth Priority 115
Configuring QoS Port-Based Settings 117
Configuring CoS Settings 118
Configuring DSCP Settings 118
Chapter 8: Managing Your Device 120
Setting Device Properties 120
Setting Password Complexity 121

Cisco RV130/RV130W Wireless Multifunction VPN Router Administration Guide 5
Contents
Configuring User Accounts 122
Importing User Accounts 123
Setting the Session Timeout Value 124
Configuring Simple Network Management (SNMP) 125
Configuring SNMP System Information 125
Editing SNMPv3 Users 126
Configuring the SNMP Traps 127
Using Diagnostic Tools 127
Network Tools 128
Configuring Port Mirroring 129
Configuring Log and E-mail Settings 130
Configuring Log Settings 130
Configuring Log E-Mailing 132
Configuring Bonjour 134
Configuring Date and Time Settings 134
Backing Up and Restoring the System 135
Backing Up the Configuration Settings 136
Restoring the Configuration Settings 137
Copying the Configuration Settings 137
Generating an Encryption Key 138
Upgrading Firmware or Changing the Language 138
Upgrading Firmware Automatically 139
Upgrading Firmware Manually 139
Changing the Language 140
Restarting the Device 140
Restoring the Factory Defaults 141

1
Cisco RV130/RV130W Wireless Multifunction VPN Router Administration Guide 5
Getting Started
The Getting Started page displays the most common configuration tasks on your
device. Click the links on the Web page to go to the relevant configuration page.
This page appears every time you start Device Manager. To change this behavior,
check Don’t show on start up.
Initial Settings
Change Default
Administrator Password Displays the Users page where you can change the administrator password and set up a guest
account. See Configuring User Accounts.
Launch Setup Wizard Launches the Setup Wizard. Follow the on-screen
instructions.
Configure WAN Settings Opens the Internet Setup page to change
parameters. For example, the device host name.
See Configuring Wired WAN Connections.
Configure LAN Settings Opens the LAN Configuration page to modify LAN
parameters. For example, the management IP
address. See Configuring LAN Settings.
Configure Wireless
Settings Open the Basic Settings page to manage the radio. See Configuring Wireless Networks.

Getting Started
Cisco RV130/RV130W Wireless Multifunction VPN Router Administration Guide 6
1
Quick Access
Device Status
Other Resources
Upgrade Router
Firmware Opens the Firmware/Language Upgrade page to update the device firmware or language pack. See
Upgrading Firmware or Changing the Language.
Add VPN Clients Opens the PPTP Server page to set up and
manage VPN tunnels. See Configuring PPTP.
Configure Remote
Management Access Opens the BasicSettingspage to enable the basic features of the device. See Configuring Basic
Firewall Settings.
System Summary Displays the System Summary page that shows
the state of the firmware, IPv4 and IPv6
configuration status, and the status of the wireless
and the firewall on the device. See Viewing the
System Summary.
Wireless Status Displays the Wireless Statistics page that shows
the state of the radio. See Viewing Wireless
Statistics.
VPN Status Displays the IPsec VPN Server page that lists the
VPN managed by this device. See Viewing Site-
to-Site IPsec VPN Connection Status.
Support Click to open the Cisco support page.
Forums Click to visit Cisco online support forums.

Getting Started
Connecting to Your Wireless Network
Cisco RV130/RV130W Wireless Multifunction VPN Router Administration Guide 7
1
Connecting to Your Wireless Network
To connect a client device (such as a computer) to your wireless network,
configure the wireless connection on the client device with the wireless security
information that you configured for the router by using the Setup Wizard.
The following steps are provided as an example; you may need to configure your
device differently. For specific instructions, consult the documentation for your
client device.
STEP 1 Open the wireless connection settings window or program for your device.
Your computer might have special software installed to manage wireless
connections, or you might find the wireless connections under the Control Panel in
the Network Connections or Network and Internet window. (The location
depends on your operating system.)
STEP 2 Enter the network name (SSID) that you chose for your network in the Setup
Wizard.
STEP 3 Choose the type of encryption and enter the security key that you specified in the
Setup Wizard.
If you did not enable security (not recommended), leave the wireless encryption
fields that were configured with the security type and passphrase blank.
STEP 4 Verify your wireless connection and save your settings.