Cisco Cisco Industrial Ethernet 3000 Series User manual

GETTING STARTED GUIDE
Cisco Catalyst Blade Switch 3000 Series for HP
Getting Started Guide
1About This Guide
2Taking Out What You Need
3HP Blade System Architecture
4Installing the Switch Module in the Blade Enclosure
5Using the Onboard Administrator to Assign an IP Address to the Switch
Module and Running Express Setup
6Managing the Switch Module
7Planning and Creating a Switch Stack (Only the Cisco Catalyst Blade Switch
3120 for HP)
8Connecting to the Switch Module Ports
9In Case of Difficulty
10 Obtaining Documentation and Submitting a Service Request
July 2008, OL-14257-02

2
1 About This Guide
This guide provides instructions on how to install your Cisco Catalyst Blade Switch 3120 for HP or
Cisco Catalyst Blade Switch 3020 for HP— referred to as the switch module—in the HP c-Class
BladeSystem and how to set up and configure your switch module. The HP c-Class BladeSystem—
referred to as the blade enclosure—supports up to eight Ethernet switch modules, which are installed
in the interconnect bays of the blade enclosure.
This guide also covers management options and troubleshooting help for the switch module.
For details on the numbers, types, and the location of the blade enclosure bays, for additional
information on the blade enclosure system, and for detailed port mapping information, see the
HP BladeSystem enclosure installation poster or the HP BladeSystem enclosure setup and installation
guide at http://www.hp.com/go/bladesystem/documentation.
For additional installation and configuration information about the switch module, see the Cisco
Catalyst Blade Switch 3000 Series for HP documentation on Cisco.com. For system requirements,
important notes, limitations, open and resolved caveats, and last-minute documentation updates about
the switch module, see the release notes, also on Cisco.com.
Note on WS-CBS3125G-S and WS-CBS3125X-S switch models:
•The WS-CBS3125G-S is the same product as the WS-CBS3120G-S.
•The WS-CBS3125X-S is the same product as the WS-CBS3120X-S.
The functionality and the performance of WS-CBS3125 switches are same as those of WS-CBS3120
switches. All Cisco Catalyst Blade Switch 3120/3125 for HP models are HP BladeSystem c-Class
compatible.
When you use the online publications, refer to the documents that match the Cisco IOS software
version that is running on the switch module. See the “Obtaining Documentation” section on
page 1-24 for more information about the switch module publications.
For translations of the warnings that appear in this publication and all safety and handling warnings
for this product, see the Regulatory Compliance and Safety Information for the Cisco Catalyst Blade
Switch 3000 Series for HP that accompanies this guide.
Before you continue with the installation, read the release notes for the blade enclosure. The release
notes are available on the HP support website at www.support.hp.com.
For warranty information about the switch module, see the Hardware Warranty Terms for the Cisco
Catalyst Blade Switch 3000 Series for HP on the documentation CD that ships with your switch
module.

3
2 Taking Out What You Need
Follow these steps:
1. Unpack and remove the switch module and the accessory kit from the shipping box.
2. Return the packing material to the shipping container, and save it for future use.
3. Verify that you have received the items shown on page 3. If any item is missing or damaged,
contact your Cisco representative or reseller for instructions.
If the switch modules are ordered with the blade enclosure, they are already installed. The unpacking
procedure for the switch module applies only if you order one separately. See the blade enclosure
documentation for the unpacking procedure for the HP equipment.
Shipping Box Contents
250286
24x
SFP19-20
19-20
21-22
SYST
S-MODE
S-MSTR
S-MMBR
CONSOLE
WS-CBS3120G-S
MODE
UID
SFP 21-22
23x
26x
STK A
STK B
Documentation
CD

4
Cisco Switch Module Descriptions
These sections describe the switch modules:
•Cisco Catalyst Blade Switch 3120 for HP, page 4
•Cisco Catalyst Blade Switch 3020 for HP, page 6
The switch module is powered from the blade enclosure backplane. The switch module does not have
a fan. The blade enclosure provides temperature management.
The switch module connects internally to the management module through 100BASE-T Ethernet links.
You can manage the switch modules through the HP Onboard Administrator management module on
a management network that is isolated from other switch traffic. You can manage the switch module
through the RS-232 console port that uses an RJ-45 connector in the switch module front-panel. You
can also manage the switch module through any of the external uplink ports.
Cisco Catalyst Blade Switch 3120 for HP
The Cisco Catalyst Blade Switch 3120 for HP is a stackable, 25 to 27 Gigabit Ethernet port, Layer 3
switch module. The number of ports depends on the type of module installed in ports 19 to 22.
See Table 1 for a description of the switch module ports. See the release notes and the software
configuration guide for information about supported Layer 3 features. See the hardware installation
guide for detailed information about stacking the switch.
The Cisco Catalyst Blade Switch 3120 for HP has a 3120G and a 3120X model. Both are
stacking-capable. The initial setup procedure for both models is the same. For more information about
the features of each model, see the hardware installation guide and the software configuration guide
for the switch module.

5
Figure 1 shows the Cisco Catalyst Blade Switch 3120 for HP switch module.
Figure 1 The Catalyst Blade Switch 3120 for HP
1Switch module 8LEDs for ports 19 and 20
2UID1LED
1. UID: unit identifier.
9Gigabit Ethernet uplink ports 23 to 26
3Health LEDs 10 Gigabit Ethernet ports 19 and 20 or 10-Gigabit Ethernet slot 1
4System status LEDs 11 LEDs for ports 21 and 22
5Mode button 12 Gigabit Ethernet ports 21 and 22 or 10-Gigabit Ethernet slot 2
6Console port 13 StackWise Plus ports
7Release latch
250154
24x
SFP19-20
19-20
21-22
SYST
S-MODE
S-MSTR
S-MMBR
CONSOLE
WS-CBS3120G-S
MODE
UID
SFP 21-22
23x
26x
STK A
STK B
7
4
3
1
2
5
6
9
8
10
13
11 12

6
Table 1 describes the Cisco Catalyst Blade Switch 3120 for HP switch module ports. Each external
port has an associated LED.
Cisco Catalyst Blade Switch 3020 for HP
The Cisco Catalyst Blade Switch 3020 for HP is a 24-Gigabit Ethernet port, Layer 2+ switch module.
Sixteen of the Gigabit Ethernet ports are internal 1000BASE-X downlink ports that connect to the
blade enclosure. The other eight Gigabit Ethernet ports are external uplink ports that provide
connections to other switches or routers. Uplink ports operate at 10/100/1000 M/ps if used as
copper-based ports and operate at 1000 M/ps if small form-factor pluggable (SFP) fiber-optic modules
are installed. See Table 2 for more detailed descriptions of the switch module ports.
Table 1 Cisco Catalyst Blade Switch 3120 for HP Port Descriptions
Port Description
Ports 1 to 16 Internal Gigabit Ethernet 1000BASE-X downlink ports that connect to the
blade enclosure.
Ports 17 to 18 Internal cross-connection ports that you can use to connect to a second
switch in the blade enclosure through a backplane connector. You can
configure these ports by using the Cisco IOS CLI. However, if the blade
switches are stacked, these ports are disabled.
Ports 19 to 22 10-Gigabit Ethernet module slots for use with the Cisco TwinGig Converter
Modules and Cisco X2 transceiver modules.
Ports 23 to 26 External 10/100/1000BASE-T copper Gigabit Ethernet uplink ports that
support auto-MDIX and autonegotiation.
Internal 100BASE-T
Ethernet port
The Ethernet management port (Fa0) is used only for switch module
management traffic, not for data traffic. It is connected to the
Onboard Administrator through the blade enclosure backplane connector.
Traffic to and from this port is isolated from the switch ports. This port
only supports autonegotiation with 100 Mb/s and full-duplex mode.
StackWise Plus ports Stacking cable ports.
Console port Switch module management port (RJ-45 connector).

7
Figure 2 shows the Cisco Catalyst Blade Switch 3020 for HP switch module. Each external port has
an associated LED.
Figure 2 The Catalyst Blade Switch 3020 for HP
1Switch module 7Health LED
2Release latch 8LEDs for SFP module ports 17 to 20
3System status LEDs 9SFP module ports 17 to 20
4Mode button 10 LEDs for Gigabit Ethernet ports 17x to 24x
5Console port 11 Gigabit Ethernet ports 17x to 24x
6UID1LED
1. UID: unit identifier.
153139
23x
24x
21x
24x
17x
18x
17x
20x
17
20
SYST
STAT
DLX
SPD
CONSOLE
UID
WS-CBS-3020-HPQ
MODE
MEDIA DETECT SFP/R-45 PORTS 17-20
17 20
18 19
2
38
10
4
9
16
7
11
5

8
Table 2 describes the switch module ports. Each external port has an associated LED.
Table 2 Cisco Catalyst Blade Switch 3020 for HP Port Descriptions
Port Description
Ports 1 to 16 Internal Gigabit Ethernet 1000BASE-X downlink ports.
Ports 17 to 20 and
Ports 17x to 20x
Dual-purpose SFP module/RJ-45 copper Ethernet uplink ports. The SFP module
ports support only Cisco 1000BASE-SX fiber-optic modules.
By default, the switch module dynamically selects the interface type that first
links up. SFP modules have precedence if both SFP module and copper Ethernet
interface types are in link-up state. You can also specifically configure each port
for either copper Ethernet or SFP modules if you do not want to use
autodetection.
The copper Ethernet ports support automatic medium-dependent interface
crossover (auto-MDIX) and autonegotiation.
For information about configuring speed and duplex settings for a
dual-purpose uplink port, see the software configuration guide.
Ports 21x to 22x External 10/100/1000BASE-T copper Gigabit Ethernet uplink ports that
support auto-MDIX and autonegotiation.
Ports 23x to 24x Dual-purpose external/internal 10/100/1000BASE-T copper Gigabit Ethernet
uplink ports. These ports can be configured for internal 1000BASE-X
cross-connection with a corresponding switch module. When ports 23x and
24x are in external operation mode, they support auto-MDIX and
autonegotiation. The default is external operation mode.
Internal
100BASE-T
Ethernet port
The Ethernet management port (Fa0) is used only for switch module
management traffic, not for data traffic. It is connected to the Onboard
Administrator through the blade enclosure backplane connector.
Console port Switch module management port (RJ-45 connector).

9
3 HP Blade System Architecture
Figure 3 shows the rear view of the blade enclosure, in which you install the switch module.
Figure 3 Rear View of the Blade Enclosure
1Blade enclosure rear view 7Interconnect module bay 5
2Blade enclosure fans 8Interconnect module bay 6
3Interconnect bay 1 with switch module installed 9Interconnect module bay 7
4Interconnect module bay 2 10 Interconnect module bay 8
5Interconnect module bay 3 11 Onboard Administrator module
6Interconnect module bay 4
153140
1
3
5
7
9
11
2
2
4
6
8
10

10
Consider these prerequisites before you install the switch module:
•Fill any unoccupied interconnect bays or any unoccupied power module bays in the blade
enclosure with blanks.
•Identify the bays in which you will insert the switch modules. Plan to install the first switch module
in bay 1, the second in bay 2, and so on up to bay 8, if possible. The bay in which you choose to
install each switch module depends on whether mezzanine or Ethernet cards are installed in the
blade enclosure and how they are configured. See the blade enclosure documentation information
about installing and configuring the mezzanine or Ethernet cards.
The interconnect module bays are physically interconnected in pairs through the blade enclosure
backplane. That is, each of these pairs—bays 1 and 2, bays 3 and 4, bays 5 and 6, and bays 7 and
8—are interconnected. If you install two switch modules in one of the paired bays, they are
internally interconnected. You must configure the switch modules to logically enable the
interconnect ports, Gigabit Ethernet ports 23 and 24. See the switch module software
configuration guide for information on configuring these ports.
•See the HP c-Class documentation for information on the port mapping between blade enclosures
and the switch modules.
4 Installing the Switch Module in the Blade Enclosure
Before you install the switch module in the blade enclosure, consider these points:
•Review and become familiar with the safety guidelines in the Regulatory Compliance and Safety
Information for the Cisco Catalyst Blade Switch 3000 Series for HP that accompanies this guide.
•Review and become familiar with the safety guidelines in the HP BladeSystem enclosure setup and
installation guide.
•Review and become familiar with the temperature, power, and grounding requirements specified
in the HP BladeSystem enclosure setup and installation guide.
Warning Only trained and qualified personnel should be allowed to install, replace, or service
this equipment. Statement 1030
Caution To prevent electrostatic-discharge (ESD) damage when installing switch modules, follow
your normal board and component handling procedures.
Note When you install a switch module, you do not need to power down the blade enclosure.