Cisco Prisma II EDR User manual

OL-32414-01
Cisco Prisma II EDR Transmitter
Installation Guide

For Your Safety
Explanation of Warning and Caution Icons
Avoid personal injury and product damage! Do not proceed beyond any symbol
until you fully understand the indicated conditions.
The following warning and caution icons alert you to important information about
the safe operation of this product:
You may find this symbol in the document that accompanies this product.
This symbol indicates important operating or maintenance instructions.
You may find this symbol affixed to the product. This symbol indicates a live
terminal where a dangerous voltage may be present; the tip of the flash points
to the terminal device.
You may find this symbol affixed to the product. This symbol indicates a
protective ground terminal.
You may find this symbol affixed to the product. This symbol indicates a
chassis terminal (normally used for equipotential bonding).
You may find this symbol affixed to the product. This symbol warns of a
potentially hot surface.
You may find this symbol affixed to the product and in this document. This
symbol indicates an infrared laser that transmits intensity-modulated light
and emits invisible laser radiation or an LED that transmits intensity-
modulated light.
Important
Please read this entire guide. If this guide provides installation or operation
instructions, give particular attention to all safety statements included in this guide.

Notices
Trademark Acknowledgments
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its
affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this
URL: www.cisco.com/go/trademarks.
Third party trademarks mentioned are the property of their respective owners.
The use of the word partner does not imply a partnership relationship between
Cisco and any other company. (1110R)
Publication Disclaimer
Cisco Systems, Inc. assumes no responsibility for errors or omissions that may
appear in this publication. We reserve the right to change this publication at any
time without notice. This document is not to be construed as conferring by
implication, estoppel, or otherwise any license or right under any copyright or
patent, whether or not the use of any information in this document employs an
invention claimed in any existing or later issued patent.
Copyright
© 2014 Cisco and/or its affiliates. All rights reserved.
Information in this publication is subject to change without notice. No part of this
publication may be reproduced or transmitted in any form, by photocopy,
microfilm, xerography, or any other means, or incorporated into any information
retrieval system, electronic or mechanical, for any purpose, without the express
permission of Cisco Systems, Inc.

OL-32414-01 iii
Contents
Important Safety Instructions v
Safe Operation for Software Controlling Optical Transmission
Equipment xv
Warning Labels xvii
Chapter 1 Module Introduction 1
EDR 85 System Overview....................................................................................................... 3
Features ........................................................................................................................ 3
System Block Diagram ............................................................................................... 4
System Description ..................................................................................................... 5
Transmitter Operation................................................................................................ 6
Receiver Operation ..................................................................................................... 7
Prisma II EDR Transmitter Overview................................................................................... 9
Transmitter Features .................................................................................................. 9
Transmitter Status Indicators.................................................................................... 9
Transmitter Optical Input........................................................................................ 10
Laser Warning ........................................................................................................... 10
EDR Transmitter Front and Back Panel..............................................................................11
Transmitter Illustration (Front and Back) .............................................................11
Transmitter Front Panel Features ........................................................................... 11
Back Panel Connectors ............................................................................................. 12
About the OPM .........................................................................................................12
Laser Warning ........................................................................................................... 13
Prisma II Chassis Host Module............................................................................................ 14
Host Module Features.............................................................................................. 14
Host Module Illustration ......................................................................................... 14
Host Module Back Panel Connectors..................................................................... 15
Module Configuration........................................................................................................... 16
Configuration Summary.......................................................................................... 16
Chapter 2 System Installation 17
Preparing for Installation...................................................................................................... 18
Equipment and Tools Needed ................................................................................ 18
Unpacking and Inspecting the Module ................................................................. 18

Contents
iv OL-32414-01
Site Requirements .................................................................................................................. 19
Access Requirements................................................................................................ 19
Equipment Rack........................................................................................................ 19
Operating Environment........................................................................................... 19
Power Requirements ................................................................................................ 19
Space Requirements.................................................................................................. 20
Prisma II Standard Chassis Style............................................................................ 20
Prisma II XD Chassis Style ......................................................................................22
Connecting the RF Cables to the Chassis ........................................................................... 23
To Connect RF Cables for Each Module................................................................ 23
Installing the HD Module in the Chassis............................................................................25
To Install the Application Modules in the Host Module .................................... 25
To Install the Module in the Chassis...................................................................... 26
To Install the Module in a Prisma II XD Chassis..................................................27
Cleaning Optical Connectors ............................................................................................... 29
Recommended Equipment...................................................................................... 29
Tips for Optimal Fiber Optic Connector Performance ........................................29
To Clean Optical Connectors .................................................................................. 30
Connecting Optical Cables ................................................................................................... 31
Cable Routing - Prisma II Chassis ..........................................................................31
Cable Routing - Prisma XD Chassis ....................................................................... 32
To Connect Optical Cables to Module................................................................... 32
Transmitter Module Setup Procedure ................................................................................ 34
Chapter 3 Maintenance and Troubleshooting 35
Maintenance............................................................................................................................ 36
Maintenance Record................................................................................................. 36
General Troubleshooting Information................................................................................ 37
Troubleshooting ........................................................................................................ 37
Equipment Needed................................................................................................... 37
Transmitter Module Troubleshooting Chart ........................................................ 38
Additional Assistance .............................................................................................. 38
Chapter 4 Customer Information 39
Glossary 41
Index 45

Important Safety Instructions
OL-32414-01 v
Important Safety Instructions
Read these instructions. Keep these instructions. Heed all warnings. Follow all
instructions. Only use attachments/accessories specified by the manufacturer.
Read and Retain Instructions
Carefully read all safety and operating instructions before operating this equipment,
and retain them for future reference.
Follow Instructions and Heed Warnings
Follow all operating and use instructions. Pay attention to all warnings and cautions
in the operating instructions, as well as those that are affixed to this equipment.
Terminology
The terms defined below are used in this document. The definitions given are based
on those found in safety standards.
Service Personnel - The term service personnel applies to trained and qualified
individuals who are allowed to install, replace, or service electrical equipment. The
service personnel are expected to use their experience and technical skills to avoid
possible injury to themselves and others due to hazards that exist in service and
restricted access areas.
User and Operator - The terms user and operator apply to persons other than service
personnel.
Ground(ing) and Earth(ing) - The terms ground(ing) and earth(ing) are synonymous.
This document uses ground(ing) for clarity, but it can be interpreted as having the
same meaning as earth(ing).
Electric Shock Hazard
This equipment meets applicable safety standards.
WARNING:
To reduce risk of electric shock, perform only the instructions that are
included in the operating instructions. Refer all servicing to qualified service
personnel only.
Electric shock can cause personal injury or even death. Avoid direct contact with
dangerous voltages at all times. The protective ground connection, where provided,
is essential to safe operation and must be verified before connecting the power
supply.

Important Safety Instructions
vi OL-32414-01
Know the following safety warnings and guidelines:
Dangerous Voltages
-Only qualified service personnel are allowed to perform equipment
installation or replacement.
-Only qualified service personnel are allowed to remove chassis covers and
access any of the components inside the chassis.
Grounding
-Do not violate the protective grounding by using an extension cable, power
cable, or autotransformer without a protective ground conductor.
-Take care to maintain the protective grounding of this equipment during
service or repair and to re-establish the protective grounding before putting
this equipment back into operation.
Installation Site
When selecting the installation site, comply with the following:
Protective Ground - The protective ground lead of the building’s electrical
installation should comply with national and local requirements.
Environmental Condition –The installation site should be dry, clean, and
ventilated. Do not use this equipment where it could be at risk of contact with
water. Ensure that this equipment is operated in an environment that meets the
requirements as stated in this equipment’s technical specifications, which may be
found on this equipment’s data sheet.
Installation Requirements
WARNING:
Allow only qualified service personnel to install this equipment. The
installation must conform to all local codes and regulations.
Equipment Placement
WARNING:
Avoid personal injury and damage to this equipment. An unstable mounting
surface may cause this equipment to fall.

Important Safety Instructions
OL-32414-01 vii
To protect against equipment damage or injury to personnel, comply with the
following:
Install this equipment in a restricted access location.
Do not install near any heat sources such as radiators, heat registers, stoves, or
other equipment (including amplifiers) that produce heat.
Place this equipment close enough to a mains AC outlet to accommodate the
length of this equipment’s power cord.
Route all power cords so that people cannot walk on, place objects on, or lean
objects against them. This may pinch or damage the power cords. Pay particular
attention to power cords at plugs, outlets, and the points where the power cords
exit this equipment.
Use only with a cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with this equipment.
Make sure the mounting surface or rack is stable and can support the size and
weight of this equipment.
The mounting surface or rack should be appropriately anchored according to
manufacturer’s specifications. Ensure this equipment is securely fastened to the
mounting surface or rack where necessary to protect against damage due to any
disturbance and subsequent fall.
Ventilation
This equipment has openings for ventilation to protect it from overheating. To
ensure equipment reliability and safe operation, do not block or cover any of the
ventilation openings. Install the equipment in accordance with the manufacturer’s
instructions.
Rack Mounting Safety Precautions
Mechanical Loading
Make sure that the rack is placed on a stable surface. If the rack has stabilizing
devices, install these stabilizing devices before mounting any equipment in the rack.
WARNING:
Avoid personal injury and damage to this equipment. Mounting this
equipment in the rack should be such that a hazardous condition is not caused
due to uneven mechanical loading.

Important Safety Instructions
viii OL-32414-01
Reduced Airflow
When mounting this equipment in the rack, do not obstruct the cooling airflow
through the rack. Be sure to mount the blanking plates to cover unused rack space.
Additional components such as combiners and net strips should be mounted at the
back of the rack, so that the free airflow is not restricted.
CAUTION:
Installation of this equipment in a rack should be such that the amount of
airflow required for safe operation of this equipment is not compromised.
Elevated Operating Ambient Temperature
Only install this equipment in a humidity- and temperature-controlled environment
that meets the requirements given in this equipment’s technical specifications.
CAUTION:
If installed in a closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater than room ambient
temperature. Therefore, install this equipment in an environment compatible
with the manufacturer’s maximum rated ambient temperature.
Handling Precautions
When moving a cart that contains this equipment, check for any of the following
possible hazards:
WARNING:
Avoid personal injury and damage to this equipment! Move any equipment
and cart combination with care. Quick stops, excessive force, and uneven
surfaces may cause this equipment and cart to overturn.
Use caution when moving this equipment/cart combination to avoid injury from
tip-over.
If the cart does not move easily, this condition may indicate obstructions or
cables that may need to be disconnected before moving this equipment to
another location.
Avoid quick stops and starts when moving the cart.
Check for uneven floor surfaces such as cracks or cables and cords.
Grounding
This section provides instructions for verifying that the equipment is properly
grounded.