Cisco Aironet 600 Series User manual

Cisco Systems, Inc.
www.cisco.com
Cisco has more than 200 offices worldwide.
Addresses, phone numbers, and fax numbers
are listed on the Cisco website at
www.cisco.com/go/offices.
Cisco Aironet 600 Series OfficeExtend
Access Point User Guide
Last Updated: August 2014
Text Part Number: OL-29882-03

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL
STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT
SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE
OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public
domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH
ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF
DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,
WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO
OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this
URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership
relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display
output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in
illustrative content is unintentional and coincidental.
Cisco Aironet 600 Series OfficeExtend Access Point User Guide
© 2005-2014 Cisco Systems, Inc. All rights reserved.

iii
Cisco Aironet 600 Series OfficeExtend Access Point User Guide
OL-29882-03
CONTENTS
Preface v
Audience v
Document Organization v
Conventions vi
Related Documentation vi
CHAPTER 1Unpacking and Installing the Access Point 1-1
Unpacking the Access Point 1-1
Placing the Access Point 1-1
Parts of the Access Point 1-3
Installing the Access Point 1-4
Resetting the Access Point 1-5
Understanding the Access Point LEDs 1-5
CHAPTER 2Access Point GUI 2-1
Accessing the GUI 2-1
Home Page 2-2
AP Info 2-3
SSID 2-3
Client 2-4
Configuration Page 2-4
System Tab 2-6
SSID Tab 2-7
DHCP Tab 2-8
WAN Tab 2-8
Firewall 2-9
Download/Upload 2-12
Event Log Page 2-13
Network Diagnostics 2-13
CHAPTER 3Configuring the Access Point 3-1
Configuring the Wireless LAN Controller IP Address on the Access Point 3-1
Configuring Radio Channels on the Access Point 3-2

Contents
iv
Cisco Aironet 600 Series OfficeExtend Access Point User Guide
OL-29882-03
Configuring Personal Wireless LANs 3-3
Troubleshooting 3-4
CHAPTER 4Functionalities of the Access Point 4-1
Using the Split Tunneling Feature for Local Printing 4-1
Prerequisites for Adding a Local Printer 4-1
Adding the Local Printer in Windows 4-2
Adding the Local Printer in Mac OS 4-3
CHAPTER 5Declarations of Conformity and Regulatory Information 5-1
Manufacturers Federal Communication Commission Declaration of Conformity Statement 5-1
Industry Canada 5-2
Canadian Compliance Statement 5-2
European Community, Switzerland, Norway, Iceland, and Liechtenstein 5-3
Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive) 5-3
Operation of Cisco Aironet Access Points in Brazil 5-6
Access Point Models 5-6
Regulatory Information 5-6
Portuguese Translation 5-7
English Translation 5-7
Declaration of Conformity for RF Exposure 5-7
Declaration of Conformity Statements 5-7

v
Cisco Aironet 600 Series OfficeExtend Access Point User Guide
OL-29882-03
Preface
The Preface contains the following sections:
•Audience, page v
•Document Organization, page v
•Conventions, page vi
•Related Documentation, page vi
Audience
This document is for experienced network administrators who configure and maintain Cisco wireless
LAN controllers and Cisco lightweight access points. It contains information useful to users who
connect to a network via a Cisco Aironet 600 Series OfficeExtend Access Point, which is referred to as
the access point or as the AP in this document.
Document Organization
The following table describes the contents of each chapter in this document:
Table 1 Document Organization
Chapter and Title Description
Chapter 1, “Unpacking and
Installing the Access Point”
This chapter provides information on unpacking and installing the
access point. It also gives you instructions on placement, and a
description of the parts of the access point.
Chapter 2, “Access Point GUI” This chapter describes the various pages in the access point’s GUI.
Chapter 3, “Configuring the
Access Point”
This chapter provides information on how to configure the access
point for use.
Chapter 4, “Functionalities of
the Access Point”
This chapter provides information about certain end-user
functionalities provided via the access point, including those which
are accessed via other external systems.
Chapter 5, “Declarations of
Conformity and Regulatory
Information”
This chapter contains declarations of conformity and regulatory
information for the Cisco Aironet 600 Series OfficeExtend Access
Point.

vi
Cisco Aironet 600 Series OfficeExtend Access Point User Guide
OL-29882-03
Conventions
The following table describes conventions used in this document:
Note Means reader needs to take note. Notes contain helpful suggestions or references to material not covered
in the manual.
Tip Means the following information will help you solve a problem.
Caution Means reader needs to be careful. In this situation, you might perform an action that could result in
equipment damage or loss of data.
Related Documentation
In addition to the information provided in this publication, you might need to refer to the following
documents:
•Cisco Wireless LAN Controller configuration guides.
http://www.cisco.com/en/US/products/ps10315/products_installation_and_configuration_guides_l
ist.html
•Cisco Wireless LAN Controller command references.
http://www.cisco.com/en/US/products/ps10315/prod_command_reference_list.html
•Cisco Wireless LAN Controller System Message Guide.
http://www.cisco.com/en/US/products/ps10315/products_system_message_guides_list.html
Table 2 Command Syntax Guide
Convention Description
boldface Commands and keywords.
italic Command input that is supplied by you.
[ ] Keywords or arguments that appear within square brackets are optional.
{ x | x | x } A choice of keywords (represented by x) appears in braces separated by
vertical bars. You must select one.
^ or Ctrl Represent the key labeled Control. For example, when you read ^D or
Ctrl-D, you should hold down the Control key while you press the D key.
screen font Examples of information displayed on the screen.
boldface screen font Examples of information that you must enter.
< > Nonprinting characters, such as passwords, appear in angled brackets.
[ ] Default responses to system prompts appear in square brackets.

vii
Cisco Aironet 600 Series OfficeExtend Access Point User Guide
OL-29882-03
•Release Notes for Cisco Wireless LAN Controllers and Lightweight Access Points.
http://www.cisco.com/en/US/products/ps10315/prod_release_notes_list.html

viii
Cisco Aironet 600 Series OfficeExtend Access Point User Guide
OL-29882-03

CHAPTER
1-1
Cisco Aironet 600 Series OfficeExtend Access Point User Guide
OL-29882-03
1
Unpacking and Installing the Access Point
This chapter provides the following information:
•Unpacking the Access Point, page 1-1
•Placing the Access Point, page 1-1
•Parts of the Access Point, page 1-3
•Installing the Access Point, page 1-4
•Resetting the Access Point, page 1-5
•Understanding the Access Point LEDs, page 1-5
Unpacking the Access Point
Each Cisco Aironet 600 Series OfficeExtend Access Point package contains the following items:
•Cisco Aironet 600 Series OfficeExtend Access Point
•Ethernet Cable
•Cisco Aironet AP600 Series Power Module (universal power supply)
•Quick reference guide
•Cisco product registration and Cisco documentation feedback cards
Placing the Access Point
To ensure the best RF coverage for your access point, place your access point in an area as close to the
wireless clients as possible and practical to do so.
If the Internet source or gateway router is in a remote area, position your access point away from metal
obstructions.
The access point can be placed/mounted in a horizontal position, as the access point has rubber feet on
its bottom panel.
The access point may also be mounted in a vertical position using the supplied cradle or wall mounted
slots.
Note The distance between the mounting hole slots is 158.75 mm (6.25 in).

1-2
Cisco Aironet 600 Series OfficeExtend Access Point User Guide
OL-29882-03
Chapter 1 Unpacking and Installing the Access Point
Placing the Access Point
Areas to avoid or places that may result in reduced range or performance are as follows.
•In a basement of a multi-story home, as the signals must penetrate many walls.
•Near large obstructions that can block the radio signals. Avoid areas like metal cabinets or
refrigerators.
•On the floor under a metal desk or other dense or conductive objects.
Note Cisco is not responsible for damages occurred by unsecured wall-mounting hardware.

1-3
Cisco Aironet 600 Series OfficeExtend Access Point User Guide
OL-29882-03
Chapter 1 Unpacking and Installing the Access Point
Parts of the Access Point
Parts of the Access Point
282287
2 3 4 5 6 7
8 9 11
12
13
1
10
1Local Ethernet LEDs 1 through 3 8WA N P o r t
2Remote LAN LED 9Remote LAN Port
3Status LED 10 Local Ethernet Ports 1 through 3
4Wireless LED 11 Reset Button
5WAN LED 12 Power Toggle Switch
6USB LED (future) 13 Power Connector
7Power Indicator LED

1-4
Cisco Aironet 600 Series OfficeExtend Access Point User Guide
OL-29882-03
Chapter 1 Unpacking and Installing the Access Point
Installing the Access Point
Installing the Access Point
To install the Cisco Aironet 600 Series OfficeExtend Access Point, follow these steps:
Step 1 Plug one end of the Ethernet cable into the Ethernet port of your home router/gateway.
Step 2 Insert the other end of the Ethernet cable into the WAN port of the 600 Series OfficeExtend Access Point.
Note The 600 Series OfficeExtend Access Point has different power requirements than other Cisco
enterprise access points, and this unit will be damaged if incorrect power is applied. Please refer
to the 600 Series OfficeExtend Access Point specifications for power supply requirements.
Step 3 Insert the power cord into the power connector of the 600 Series OfficeExtend Access Point.
Step 4 Plug the other end of the power cord into your power source.
Step 5 Press the power toggle switch on the access point to the ON position.
Step 6 Use the 600 Series OfficeExtend Access Point LED table (Table 1-1 on page 1-5) to understand the
LEDs located on the top panel of the access point.
Note The process of connecting the 600 Series OfficeExtend Access Point should only take 1 to 2 minutes.
Your unit may require a software image download. If so, once the connection is made, the Status LED
on the top of the unit will flash blue. The Status LED continues flashing until download is complete.
When the download is complete, your access point will restart. Once connected to the controller, the
Status LED will display a solid blue or purple.
Step 7 If your IT administrator has not pre-provisioned the 600 Series Office Extend AP with the IP address of
the Primary Wireless LAN Controller, please follow the steps in the procedure “Configuring the Wireless
LAN Controller IP Address on the Access Point” section on page 3-1, to configure this address.
Note You do not need to configure any SSIDs for your 600 Series OfficeExtend Access Point to connect to
your company network. The access point receives the company SSID when it connects to the company
network by way of the Internet. If you have problems connecting to your company network, contact your
IT administrator. You can configure your local SSID Wireless LAN for other devices. See “Configuring
Radio Channels on the Access Point” section on page 3-2 for more information.
DSL/Cable
Modem
Cisco Aironet
600 Series
OfficeExtend AP
Router Client
282286

1-5
Cisco Aironet 600 Series OfficeExtend Access Point User Guide
OL-29882-03
Chapter 1 Unpacking and Installing the Access Point
Resetting the Access Point
Note Cisco Aironet 600 Series OfficeExtend access points are designed to work behind a router or other
gateway device that is using network address translation (NAT). NAT allows a device, such as a home
router or gateway, to act as an agent between the Internet (public) and a personal network (private),
thereby enabling an entire group of computers to be represented by a single IP address. There is not limit
to the number of Cisco Aironet 600 Series OfficeExtend access points that can be deployed behind a
single NAT device.
Resetting the Access Point
To reset a 600 Series OfficeExtend AP, hold the mode button (next to the power button) down for
20 seconds to clear the configuration and restart the unit with the factory default settings.
Understanding the Access Point LEDs
The LEDs on the top panel indicate the operating status of the unit. Table 1-1 provides LED status
indications for 600 Series OfficeExtend Access Points. A properly functioning and configured AP
transitions from blinking blue to solid within ten minutes. Usually the time will be much shorter.
Table 1-1 LED Status Indications for 600 Series OfficeExtend Access Points
Status LED Meaning
Purple Association status, when CAPWAP is connected: Normal
operating condition, but no wireless client associated.
Blue Association status, when CAPWAP is connected: Normal
operating condition, at least one wireless client association.
Flashing blue Operating Status: Software upgrade in progress.
Flashing orange Operating Status: No IP address, waiting for DHCP IP.
Cycling through purple, orange, and
blue
Operating Status: Discovery/join process in progress, no
client associated.
Cycling through purple, orange Operating Status: Discovery/join process in progress, with
client associated.
Orange Cisco IOS errors: Software failure; try disconnecting and
reconnecting unit power.

1-6
Cisco Aironet 600 Series OfficeExtend Access Point User Guide
OL-29882-03
Chapter 1 Unpacking and Installing the Access Point
Understanding the Access Point LEDs

CHAPTER
2-1
Cisco Aironet 600 Series OfficeExtend Access Point User Guide
OL-29882-03
2
Access Point GUI
This chapter provides the following information:
•Accessing the GUI, page 2-1
•Home Page, page 2-2
•Configuration Page, page 2-4
•Event Log Page, page 2-13
•Network Diagnostics, page 2-13
Accessing the GUI
Follow these steps to access the Cisco Aironet 600 Series OfficeExtend access point GUI.
Step 1 Connect your laptop to the local Ethernet port 1, or 2 on the 600 Series OfficeExtend access point.
Note Ethernet port 4 (Remote LAN port) may not be used to configure the 600 Series OfficeExtend
access point.
Step 2 With the 600 Series OfficeExtend access point connected to your home router/gateway as described in
the procedure “Installing the Access Point” section on page 1-4, enter the IP address of the 600 Series
OfficeExtend access point in the Address field of your Internet browser (http://<ap-ipaddress>) and
click Go.
Note The default IP address is 10.0.0.1.
Note Make sure your laptop is not connected to your company’s network using a virtual private
network (VPN) connection.
The 600 Series Office Extend Access Point Login page is displayed.
Step 3 When prompted, enter the username and password to log into the access point.
Note The default username and password are admin and admin.

2-2
Cisco Aironet 600 Series OfficeExtend Access Point User Guide
OL-29882-03
Chapter 2 Access Point GUI
Home Page
The 600 Series OfficeExtend Access Point welcome page is displayed.
Step 4 On the 600 Series OfficeExtend Access Point welcome page, click Enter. The 600 Series Office Extend
Access Point Home page is displayed.
Figure 2-1 Home Page with AP Info Tab View
The GUI consists of these pages:
•Home Page
•Configuration Page
•Event Log Page
•Network Diagnostics
•Help Page
Note When modifying any of the settings described in the following sections, ensure that you click Apply for
the settings to take effect.
Home Page
This is a multi-tab page shows general information about the AP settings, information about configured
Local SSIDs and available Corporate SSIDs, and a summary of the client association statistics. It
contains the following tabs:
•AP Info
•SSID
•Client

2-3
Cisco Aironet 600 Series OfficeExtend Access Point User Guide
OL-29882-03
Chapter 2 Access Point GUI
Home Page
AP Info
The AP Info tab (see Figure 2-1) shows the access point name, IP address, AP mode, AP MAC address,
AP uptime, software version, CAPWAP status, and WAN gateway status.
This page also shows radio-specific information including status, frequency/channel, transmit power,
number of packets in and out, and number of bytes in and out.
The CAPWAP status shows the status of the AP’s CAPWAP connection with the controller. The
CAPWAP status can be:
•Noop—Indicates CAPWAP is in No operation state
•Init—Indicates CAPWAP is in initialization process state
•Discovery—Indicates CAPWAP is in discovery state
•DTLS Setup—Indicates DTLS connection is in progress
•DTLS Teardown—Indicates DTLS connection is down
•Join—Indicates CAPWAP is in Join state
•Connected—Indicates AP and Controller is in Connected state
•Image Data—Indicates CAPWAP connection has been established and is downloading the image
from controller
•Configure - Indicates CAPWAP is in configuration state
•Sulking—Indicates CAPWAP bad/stuck state
•Idle—Indicates CAPWAP is in idle state without any operation
If the WAN connection is established and the AP’s Gateway is reachable then the WA N status is shown
as Reachable, else it is shown as Not Reachable.
SSID
The SSID tab (see Figure 2-2) lists configured Local SSIDs and available Corporate SSIDs and the
configured security policy. Additionally, for Corporate SSIDs, split-tunnel status is also displayed.

2-4
Cisco Aironet 600 Series OfficeExtend Access Point User Guide
OL-29882-03
Chapter 2 Access Point GUI
Configuration Page
Figure 2-2 Home–SSID Tab
Client
The Client tab (see Figure 2-3) give the details of associated clients with Local as well as Corporate
SSIDs. For each connected client, this page reports the client MAC address, WLAN SSID, elapsed
association time, number of bytes in and out, number of duplicates and retries, and the number of failed
decryptions.
Figure 2-3 Home–Client Tab
Configuration Page
This page which allows you to configure different options like personal SSID, local DHCP server, etc.
The Configuration page is a multi-tab page which allows you to configure the following options:
The main options that can be configured on this page are:
•System

2-5
Cisco Aironet 600 Series OfficeExtend Access Point User Guide
OL-29882-03
Chapter 2 Access Point GUI
Configuration Page
•SSID
•DHCP
•WA N
•Firewall
•Download/Upload
Wherever applicable, default values will be shown.

2-6
Cisco Aironet 600 Series OfficeExtend Access Point User Guide
OL-29882-03
Chapter 2 Access Point GUI
Configuration Page
System Tab
The System tab (see Figure 2-4) displays general system information, such as username and password
for the access point and radio interface information.
Figure 2-4 Configuration–System Tab