Cisco WET200 Wireless-G Business Ethernet Bridge User manual

Data Sheet
© 2008 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 1 of 4
Cisco WET200 Wireless-G Business Ethernet Bridge
Cisco Small Business Access Points
High-Speed Wireless Bridging for Small Businesses with Multiple Locations
Highlights
●Securely connects separate wired networks spanning different locations
●Connects to Power over Ethernet devices, simplifying installation and eliminating the need
for and cost of installing external power supplies
●Increases wireless throughput and range and reduces “dead spots” in the wireless
coverage area with RangeBooster technology
●Protects business information with enhanced security and advanced encryption
Figure 1. Cisco WET200 Wireless-G Business Ethernet Bridge
Product Overview
The Cisco®WET200 Wireless-G Business Ethernet Bridge (Figure 1) transparently bridges
separate Ethernet networks together wirelessly and is ideal for small businesses with offices and
resources that are in different office suites of a building or in closely adjacent buildings. The
WET200 is a Power over Ethernet (PoE) end device, so it can be installed anywhere an Ethernet
cable can be run if there is no ready access to a power outlet. PoE enables delivery of both data
and power to the Cisco WET200. An AC adapter is also included for use if the device installation
site has a power outlet nearby.
Advanced security features include Wi-Fi Protected Access (WPA2) with up to 256-bit Advanced
Encryption Standard (AES) encryption using Extensible Authentication Protocol (EAP), giving small
businesses the protection they need to communicate and transfer data securely. The integrated
quality of service (QoS) features provide consistent voice and video quality on both the wired and

Data Sheet
© 2008 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 2 of 4
wireless networks, enabling the deployment of business-quality voice over IP (VoIP) and video
applications.
Additional support for VLANs, Simple Network Management Protocol (SNMP), Spanning Tree
Protocol, and port mirroring make this an ideal solution for network administrators to incorporate
into larger organizations.
RangeBooster technology is a compatible add-on to standard Wireless-G that nearly doubles the
wireless signal range and increases throughput by up to 35 percent. Unlike ordinary wireless
technologies that are hampered by signal reflections, RangeBooster devices use smart antennas
and embedded processors to detect and decode reflected signals to enhance and boost data
throughput. This capability also helps to reduce or eliminate “dead spots” within the wireless
coverage area.
Features
●5-port 10/100 BASE-T Ethernet managed switch, autosensing half/full duplex and medium
dependent interface (MDI) and MDI crossover (MDI-X)
●Supports 802.11b and 802.11g wireless connection to access point
●Easy installation and configuration via a web interface
●Supports Wired Equivalent Privacy (WEP), WPA Pre-Shared Key (WPA-PSK), WPA2-PSK,
WPA-ENT, and WPA2-ENT wireless encryption
●Supports 802.1X, Extensible Authentication Protocol Transport Layer Security (EAP-TLS),
and Protected EAP (PEAP) authentication with RADIUS server
●SMA detachable dipole antennas with 1x2 multiple-input, multiple-output (MIMO) to
increase coverage
●Supports PoE or external DC power
●Supports SNMP and features an intuitive web-based interface
●Support 802.1Q and port-based VLAN on LAN switch - 1 VLAN bridged over wireless
●Support 802.1p, IP type of service (ToS), and differentiated services code point (DSCP)
based QoS on LAN switch
●Supports rate limiting on both wired switch and wireless interface
●Supports Spanning Tree Protocol, port mirroring, and MAC-based access control lists
(ACLs)
Specifications
Table 1 lists the specifications, package contents, and minimum requirements for the Cisco
WET200 Wireless-G Business Ethernet Bridge.
Table 1. Specifications for the Cisco WET200 Wireless-G Business Ethernet Bridge
Specifications
Standards IEEE 802.11g, IEEE 802.11b, IEEE 802.3, IEEE 802.3u, IEEE 802.3af (PoE), 802.1p (QoS
priority), 802.1Q (VLAN), 802.1X (security authentication), 802.11i ready (security WPA2),
802.11e ready (wireless QoS)
Ports Five 10/100 BASE-T Ethernet, 12V DC power
Buttons Reset
Cabling type Unshielded twisted pair (UTP) Category 5
LEDs Power, PoE, Wireless, Ethernet 1-5

Data Sheet
© 2008 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 3 of 4
Operating system Linux
Setup/Config
Web user interface Built in web user interface for easy browser-based configuration (HTTP/HTTPS)
Management
SNMP version SNMP version 1, 2c, 3
Web firmware upgrade Firmware upgradable through web browser
Dynamic Host Configuration
Protocol (DHCP) DHCP client
Operating Modes
Wireless client Infrastructure or ad hoc
Wireless
Spec/modulation Radio and modulation type: 802.11b/DSSS, 11g/OFDM
Channels Operating channels: 11 North America, 13 most of Europe (ETSI and Japan)
Internal antennas None
External antennas 2 (omnidirectional) SMA detachable
Transmit power Transmit power (adjustable) at normal temperature range: 802.11b: 12 ±1 dBm; 802.11g:
16 ± 1 dBm
Antenna gain in dBi 2
Receiver sensitivity 11g: 54 Mbps at -69 dBm, 11b: 11 Mbps at -82 dBm
Security
WEP/WPA/WPA2 WEP 64-bit/128-bit, WPA-PSK, WPA2-PSK, WPA-ENT, WPA2-ENT
Access control MAC-based ACL between wired and wireless interfaces
802.1X IEEE 802.1X support
Quality of Service
QoS ●4 queues
●Queue mapping on ingress based on default priority, 802.1p tag, DSCP, and IP ToS
●Rate limiting on both ingress and egress direction
●Wi-Fi Multimedia (WMM) priority settings for wireless egress
General
●16 VLAN groups
●256 MAC address entries across wireless bridge
●1024 MAC address entries in the switch
Environmental
Dimensions
W x H x D 6.69 x 8.07 x 7.68 in. (170 x 205 x 195 mm)
Weight 12.17 oz (345 g)
Power 12V 0.5A DC input and IEEE 802.3af-compliant PoE
Maximum power draw: 4.2W
Certification FCC, ICES-003, CE
Operating temperature 32º to 104ºF (0º to 40ºC)
Storage temperature -4º to 158ºF (-20º to 70ºC)
Operating humidity 10% to 85% noncondensing
Storage humidity 5% to 90% noncondensing

Data Sheet
© 2008 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 4 of 4
Package Contents
●Cisco WET200 Wireless-G Business Ethernet Bridge
●2 SMA detachable dipole antennas
●User guide on CD-ROM
●Quick installation guide
●Ethernet network cable
●Power adapter
●Product stands
●Registration card
Minimum Requirements
●PC or devices with Ethernet port
●802.11b or 802.11g wireless access point
●Switch/router with PoE support or PoE injector when used with PoE
●Web-based configuration: Java-enabled web browser
Product Warranty
3-year limited hardware warranty with return to factory replacement and 90-day limited software warranty.
Cisco Limited Warranty for Cisco Small Business Series Products
This Cisco Small Business product comes with a 3-year limited hardware warranty with return to
factory replacement and a 90-day limited software warranty. In addition, Cisco offers software
application updates for bug fixes and telephone technical support at no charge for the first 12
months following the date of purchase. To download software updates, go to:
http://www.cisco.com/go/smallbiz.
Product warranty terms and other information applicable to Cisco products are available at
http://www.cisco.com/go/warranty.
For More Information
For more information on Cisco Small Business products and solutions, visit:
http://www.cisco.com/smallbusiness.
Printed in USA C78-501862-00 11/08