Cisco IW3702 User manual

Cisco IW3702 Access Point Getting Started Guide
Cisco IW3702 Access Point Getting Started Guide 2
Organization 2
Conventions 2
Overview 3
Installation 14
Antennas and RF Accessories 25
Configuration 48
Technical Specifications 63
Ports and Connectors 72
Related Documentation 75
Obtaining Documentation and Submitting a Service Request 75

Revised: August 18, 2017,
Cisco IW3702 Access Point Getting Started Guide
This guide documents the hardware features of the Cisco IW3702 access point. It describes the physical and performance characteristics
of each access point, and explains how to install and configure an access point.
This publication is for the network technicians who install and configure access points. You must be familiar with network structures,
terms, and concepts.
The Cisco IW3702 access point is referred to as access point in this document.
Organization
This guide includes the following sections:
DescriptionSection
Describes text conventions used in this document.Conventions, on page 2
Describes the major components and features of the access
point.
Overview, on page 3
Provides warnings, safety information, and installation
information you need to install your access point.
Installation, on page 14
Provides information about the antennas used by the access
point and the antenna configurations deployed.
Antennas and RF Accessories, on page 25
Describes the steps to configure the access point.Configuration, on page 48
Lists technical specifications for the access point.Technical Specifications, on page 63
Describes the port and connector pinouts for the access point.Ports and Connectors, on page 72
Conventions
This document uses the following conventions.
IndicationConvention
Commands and keywords and user-entered text appear in bold
font.
bold font
Document titles, new or emphasized terms, and arguments for
which you supply values are in italic font.
italic font
Elements in square brackets are optional.[ ]
2

IndicationConvention
Required alternative keywords are grouped in braces and
separated by vertical bars.
{x | y | z }
Optional alternative keywords are grouped in brackets and
separated by vertical bars.
[ x | y | z ]
A nonquoted set of characters. Do not use quotation marks
around the string or the string will include the quotation marks.
string
Terminal sessions and information the system displays appear
in courier font.
courier font
Nonprinting characters such as passwords are in angle brackets.< >
Default responses to system prompts are in square brackets.[ ]
An exclamation point (!) or a pound sign (#) at the beginning
of a line of code indicates a comment line.
!, #
Means reader take note . Notes contain helpful suggestions or references to material not covered in the
manual.
Note
Means reader be careful. In this situation, you might perform an action that could result in equipment
damage or loss of data.
Caution
IMPORTANT SAFETY INSTRUCTIONSMeans danger. You are in a situation that could cause
bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical
circuitry and be familiar with standard practices for preventing accidents. Use the statement number
provided at the end of each warning to locate its translation in the translated safety warnings that
accompanied this device.SAVE THESE INSTRUCTIONS
Danger
Overview
This document describes the Cisco IW3702 access point. The access point is an IEEE 802.11a/b/g/n/ac compliant, dual-band WiFi
access point with external antennas.
The access point is IP67 rated, ruggedized, and certified for on-board rail and outdoor use-cases such as train and trackside, mining,
intelligent transportation systems, and smart city applications. You can mount the access point on a DIN rail in an industrial enclosure.
Its components are designed to withstand extremes in temperature, vibration, and shock common in industrial environments.
The access point features:
3

•IEEE 802.11a/b/g/n compliant operation
•IEEE 802.11ac Wave 1 support
•Dual-radio design for 2.4 GHz and/or 5 GHz bands
•4x4 multiple-input multiple-output (MIMO) technology with three spatial streams
•Cisco CleanAir support for 20, 40, and 80 MHz channels
•DC input port (M12 connector)
•2 Power over Ethernet (PoE) ports with M12 X-code connectors:
◦1 x PoE-IN Gigabit Ethernet port compliant with IEEE 802.3at POE+ PD
◦1 x PoE-OUT Gigabit Ethernet port compliant with IEEE 802.3af POE PSE
•RS232 console port with cover (RJ-45 connector)
•4 antenna ports (N connector-female)
•Rugged IP67 rated housing and -40 to 167°F (-40 to 75°C) operating temperature range (ambient—without solar loading or
wind cooling)
•Compact size for space constrained environments
Access Point Models
There are two access point models, based on antenna configuration. The following table lists the available IW3702 models.
Table 1: Access Point Models
DescriptionModel
Cisco IW3700 Series Access Points with Regulatory Domain Code1
Access point with four antenna connectors: 2 on the top and
2 on the bottom.
IW3702-2E-x-K9
Access point with four antenna connectors on top side.IW3702-4E-x-K9
Cisco IW3700 Series Universal Access Points
Access point with four antenna connectors: 2 on the top and
2 on the bottom.
IW3702-2E-UXK9
Access point with four antenna connectors on top side.IW3702-4E-UXK9
1Regulatory Domains: (x=regulatory domains)Domain codes available for the IW3700 Series are x=A, B, D, E, M, R, Q, S, and Z. Other regulatory domains
are supported by the universal access points. Customers are responsible for verifying approval for use in their individual countries. To verify approval and to
identify the regulatory domain that corresponds to a particular country, visit https://www.cisco.com/go/aironet/compliance.
4

Bottom and Top Panel Views
Figure 1: Cisco IW3702-2E-UXK9/IW3702-2E-x-K9 Bottom Panel View
Power (PWR) connector6Status LED1
Console (CON) port7Antenna port B2
Antenna port A8PoE OUT port3
Ground connection9PoE IN port4
Protective vent port / Reset
button (covered)
5
5

There are four antenna ports on the Cisco IW3702-2E-UXK9/IW3702-2E-x-K9 model: two on the top
and two on the bottom.
Note
Figure 2: Cisco IW3702-2E-UXK9/IW3702-2E-x-K9 Top Panel View
Antenna port A3Antenna port C1
Antenna port B4Antenna port D2
6

There are four antenna ports on the Cisco IW3702-4E-UXK9/IW3702-4E-x-K9 model: all four connectors
are on the top side.
Note
Figure 3: Cisco IW3702-4E-UXK9/IW3702-4E-x-K9 Bottom Panel View
Power (PWR) connector5Status LED1
Console (CON) port6PoE OUT port2
Ground connection7PoE IN port3
Protective vent port / Reset
button (covered)
4
7

Figure 4: Cisco IW3702-4E-UXK9/IW3702-4E-x-K9 Top Panel View
Antenna port B3Antenna port C1
Antenna port D4Antenna port A2
Bottom Panel Components
This section describes the bottom panel components.
Status LED
The Status LEDs provide information on access point status, activity, and performance. The following table describes status LED
states.
8

Table 2: Status LED
System StateLED ColorMessage Type
DRAM memory test in progress.Blinking pinkBoot loader status
DRAM memory test OK.
Board initialization in progress.
Initializing flash file system.
Flash memory test OK.
Initializing Ethernet.
Ethernet OK.
Starting Cisco IOS.
Initialization successful.
Normal operating condition but no
wireless client association.
GreenClient association status
Normal operating condition with at least
one wireless client association.
Blue
Software upgrade in progress.Blinking blueOperational status
Discovery/join process in progress.Cycling green-red-off
Access point location command invoked.Rapidly cycling blue-green-red
Ethernet link not operational.Blinking red
Configuration recovery in progress
(MODE button pushed for 2 to 3
seconds).
Blinking blueBoot loader warnings
Ethernet failure or image recovery
(MODE button pushed for 20 to 30
seconds).
Red
Image recovery in progress (MODE
button released).
Blinking pink
9

System StateLED ColorMessage Type
DRAM memory test failure.RedBoot loader errors
FLASH file system failure.Blinking red-blue
Environment variable failure.Blinking red-off
Bad MAC address.
Ethernet failure during image recovery.
Boot environment failure.
No Cisco image file.
Boot failure.
Software failure. Disconnect and
reconnect unit power.
RedCisco IOS errors
General warning. Insufficient inline
power.
Cycling blue-green-red-off
AP waiting to be primed.Cycling red-green-offAP status when provisioned by Cisco
AirProvision
AP priming via Cisco NDP in progress.Blinking white
AP upon successful connection to Cisco
AirProvision.
Blinking teal (for 15 seconds)
AP priming via Cisco AirProvision in
progress.
Blinking blue
AP primed to wrong regulatory domain.Chirping red
PWR Connectors
There are two options for powering the access point:
•DC input over the PWR connector.
•PoE inline power over the PoE IN port.
10