Cisco MERAKI MR34 User manual

MR34 Installation Guide
The Cisco Meraki MR34 is a dual-band enterprise class 802.11ac cloud-managed access point. Designed for high
capacity and high density, the MR34 meets the needs of the most demanding environments, and also includes the first
ever cloud-managed third radio dedicated to optimizing the RF environment and securing the airwaves.
Package Contents
The MR34 package contains the following:
• MR34 Cloud-Managed Access Point
• Mount cradle including built-in level tool
1

• Drop ceiling mount kit
• Wall screws, wall screw anchors, and security screws
• Spare hardware
Understanding the MR34
Your Meraki MR34 has the following features:
2

The mount cradle has the following features:
3

Security Features
The MR34 features multiple options for physically securing the access point after installation:
1. Security screw – The accessory kit includes screws that can be used to secure the access point to the mount
cradle. Engaging the security screw prevents accidental dislodging and theft.
2. Kensington lock – The access point contains a hard point that allows it to be secured to any nearby permanent
structure using a standard Kensington lock.
Ethernet Ports
The MR34 features a Gigabit Ethernet R 45 port that accepts 802.3at and 802.3af power (labeled “Eth0, PoE”). This
port should be used for uplink to your WAN connection.
Power Source Options
The MR34 access point can be powered using either the Meraki AC Adapter, PoE Injector (both sold separately), or a
third-party PoE switch.
Factory Reset Button
If the button is pressed and held for at least five seconds and then released, the MR34 will reboot and be restored to its
original factory settings by deleting all configuration information stored on the unit.
LED Indicators and Run Dark Mode
Your MR34 is equipped with a multi-color LED light on the front of the unit to convey information about system
functionality and performance:
• Orange - AP is booting (permanent Orange suggests hardware issue)
• Rainbow - AP is initializing/scanning
• Blinking Blue - AP is upgrading
• Green - AP in Gateway mode with no clients
• Blue - AP in Gateway mode with clients
4

• Blinking Orange - AP can't find uplink
The MR34 may be operated in “Run Dark” mode for additional security and to reduce the visibility of the access point. In
this mode, the LED will not be illuminated. This mode may be enabled through Meraki dashboard.
Pre-Install Preparation
You should complete the following steps before going on-site to perform an installation.
Configure Your Network in Dashboard
The following is a brief overview only of the steps required to add an MR34 to your network. For detailed instructions
about creating, configuring and managing Meraki wireless networks, refer to the online documentation
(documentation.meraki.com/mr).
1. Login to http://dashboard.meraki.com. If this is your first time, create a new account.
2. Find the network to which you plan to add your APs or create a new network.
3. Add your APs to your network. You will need your Meraki order number (found on your invoice) or the serial
number of each AP, which looks like Qxxx-xxxx-xxxx, and is found on the bottom of the unit. You will also need
your Enterprise license key, which you should have received via email.
4. Go to the map / floor plan view and place each AP on the map by clicking and dragging it to the location where you
plan to mount it.
Check and Upgrade Firmware
To ensure your MR34 performs optimally immediately following installation, it is recommended that you facilitate a
firmware upgrade prior to mounting your MR34.
1. Attach your MR34 to power and a wired Internet connection. See the "Power the MR34" section for details.
2. The MR34 will turn on and the LED will glow solid orange. If the unit does not require a firmware upgrade, the LED
will turn either green (no clients associated) or blue (clients associated) within thirty seconds.
* If the unit requires an upgrade, the LED will begin blinking orange until the upgrade is complete, at which point the LED
will turn solid green or blue. You should allow at least a few minutes for the firmware upgrade to complete, depending on
the speed of your internet connection.
Check and Configure Firewall Settings
If a firewall is in place, it must allow outgoing connections on particular ports to particular IP addresses. The most
current list of outbound ports and IP addresses for your particular organization can be found here.
Assigning IP Addresses to MR34s
All gateway MR34s (MR34s with Ethernet connections to the LAN) must be assigned routable IP addresses. These IP
addresses can be dynamically assigned via DHCP or statically assigned.
5

Dynamic Assignment
When using DHCP, the DHCP server should be configured to assign a static IP address for each MAC address
belonging to a Meraki AP. Other features of the wireless network, such as 802.1X authentication, may rely on the
property that the APs have static IP addresses.
Static Assignment
Static IPs are assigned using the local web server on each AP. The following procedure describes how to set the static
IP:
1. Using a client machine (e.g., a laptop), connect to the AP wirelessly (by associating to any SSID broadcast by the
AP) or over a wired connection.
2. If using a wired connection, connect the client machine to the MR34 either through a PoE switch or a PoE Injector.
If using a PoE switch, plug an Ethernet cable into the MR34’s Ethernet jack, and the other end into a PoE switch.
Then connect the client machine over Ethernet cable to the PoE switch. If using a PoE Injector, connect the MR34
to the “PoE” port of the Injector, and the client machine to the “LAN” port.
3. Using a web browser on the client machine, access the AP’s built-in web server by browsing
to http://my.meraki.com. Alternatively, browse to http://10.128.128.128.
4. Click on the “Uplink Configuration” tab. Log in. The default login is the serial number (e.g. Qxxx-xxxx-xxxx), with no
password (e.g., Q2DD-551C-ZYW3).
5. Configure the static IP address, net mask, gateway IP address and DNS servers that this AP will use on its wired
connection.
6. If necessary, reconnect the AP to the LAN.
Static IP via DHCP Reservations
Instead of associating to each Meraki AP individually to configure static IP addresses, an administrator can assign static
IP addresses on the upstream DHCP server. Through “DHCP reservations,” IP addresses are “reserved” for the MAC
addresses of the Meraki APs. Please consult the documentation for the DHCP server to configure DHCP reservations.
Collect Tools
You will need the following tools to perform an installation:
Collect Additional Hardware for Installation
You will need the following hardware to perform an installation:
6

Installation Instructions
Choose Your Mounting Location
A good mounting location is important to getting the best performance out of your MR34 access point. Keep the
following in mind:
1. The device should have unobstructed line of sight to most coverage areas. For example, if installing in an office
filled with workspaces divided by mid-height cubicle walls, installing on the ceiling or high on a wall would be ideal.
2. Power over Ethernet supports a maximum cable length of 300 ft (100 m).
3. If being used in a mesh deployment, the MR34 should have line of sight to at least two other Meraki devices. For
more detailed instructions regarding access point location selection, reference the Meraki Network Design Guide
(meraki.cisco.com/library/).
Install the MR34
For most mounting scenarios, the MR34 mount cradle provides a quick, simple, and flexible means of mounting your
device. The installation should be done in two steps. First, install the mount cradle to your selected location. Then,
attach the MR34 to the mount cradle.
Attach the mount cradle
The MR34 mount cradle can be used to install your access point in a wide range of scenarios: wall or solid ceiling, below
a drop ceiling, on various electrical junction boxes.
7

The mount cradle contains a variety of hole patterns that are customized for each installation scenario. The mounting
template (included inbox with mount cradle) should be used to drill holes for wall mounts and also to identify the correct
hole patterns in the mount cradle that should be used for each type of mount. The included mount cradle
template shows the hole patterns that should be used for each type of mount.
Wall or Solid Ceiling Mount Using mount cradle
Using included wall anchors and screws, attach the mount cradle to your mounting wall or ceiling. It is recommended
that the MR34 be mounted to a wall or solid ceiling using the mount cradle for physical security reasons.
Drop ceiling mount using mount cradle
To mount your MR34 on a drop ceiling T-rail, use the included drop ceiling mounting accessory kit. The accessory kit
can be used to mount to most 9/16”, 15/16” or 1 ½” T-rails. The kit contains:
• Drop ceiling mounting clips with set screws
• 6-32x4 mm screws
• 6-32x7 mm screws only used for recessed rail mount (uncommon)
8

• 2 rubber spacers
1. Attach the T-rail clips to the T-rail by rotating them and snapping them into place as shown. The black foam pads
should be compressed slightly after installation.
2. Using the dashed lines on the mount cradle template as a guide, set the proper spacing of the T-rail clips on the T-
rail.
3. Tighten the set screws on the T-rail clips to secure the clips using a 5/64”(2 mm) hex key.
9

4. Attach the mount cradle to the T-rail clips using the mount cradle holes (marked with a “T“).
Tip: Pre-assemble rubber spacers and screws to the mount cradle. The mount cradle can then be held with one hand
while the other hand holds a screwdriver. If mounting your MR34 to a dropped ceiling, skip to the "Power the MR34"
section.
Electrical Junction Box Mount Using mount cradle
The MR34 can be mounted to a 4” square cable junction box, a 3.5 or 4” round cable junction box, or various U.S. and
European outlet boxes (mounting screws are not included).
Using appropriate mounting hardware for your specific type of junction box, attach the mount cradle to the junction box.
Power the MR34
If mounting to an electrical junction box, feed the Ethernet cable through the cable access hole in the mount cradle. If
mounting to a wall or ceiling, the Ethernet cable will feed from behind the MR34.
Powering the MR34 with the Meraki AC Adapter (sold separately)
1. Plug the power cord into the MR34 and the other end into a wall outlet.
2. Plug an Ethernet cable that is connected to an active Ethernet connection into the Eth0 port on the MR34.
Powering the MR34 with the Meraki 802.3at Power over Ethernet Injector (sold separately)
1. Plug the power cord into the PoE Injector and the other end into wall power.
2. Plug an Ethernet cable that is connected to an active Ethernet connection into the “IN“ port on the injector.
3. Route Ethernet cable from the “OUT“ port on the injector to the Eth0 port in the cable bay of the MR34.
10