clare ClareOne Rate of Rise Assembly instructions

© 28MAY20 Clare Controls, LLC. 1 / 3 DOC ID –1945 • Rev 03
ClareOne Rate of Rise Heat Detector
Installation Sheet
Last modified: 05/28/20
Model Number: CLR-C1-HT
Description
The ClareOne Rate-Of-Rise heat detector uses a built-in
thermistor to sample and report on a specific set temperature
or a sudden rise in temperature.
Heat –selectable 135F or 200F
Rate of Rise –rapid temp rise 12F per minute
Note: The device is powered by a 3V lithium battery providing
up to 10 years of battery life.
Installation
Heat detectors are normally installed in areas that are prone to
smoke such as kitchens and garages.
Installation notes:
•Avoid areas that may have rapidly increasing
temperatures such as fireplaces, stoves, heaters, etc.
•When mounting the detector should be placed on a ceiling
at least 4 inches away from any wall. If placed on a wall
the detector must be within 6 inches of the ceiling.
•If using the sensor with the heat setting at 135°F make
sure the ceiling location does not exceed this temperature.
Setup:
The detector can be setup to detect a fixed temperature of
either 135F or 200F.
Low –135F
High –200F
Note: if no jumper is installed the detector is set to 200F
To set detection temperature: Use the jumper to select Low
or Hi.
Programming
To add the sensor to your panel and for detailed programming
instructions, refer to the ClareOne Wireless Security and Smart
Home Panel User Manual (DOC ID 1871).
To add the detector:
1. Put the ClareOne panel in “add mode” and follow the
displayed instructions for adding the sensor.
2. Open the sensor body case and depress the tamper
switch.
3. Exit “add mode.”

2 / 3 DOC ID –1945 • Rev 03
Mounting the detector
1. Locate the base mounting holes and mount the base to
the wall or ceiling with the appropriate hardware.
2. Attach the detector to the mounting base.
Replacing the batteries
Battery life depends on the temperature of the installation
environment. When the battery voltage gets low, the detector
transmits a low battery signal to the panel. The panel then
activates trouble beeps to notify the customer that the detector
battery must be replaced.
Replace the battery immediately when this condition occurs,
using the following battery: Panasonic CR123A 3V
Battery disposal
The batteries used in this sensor are lithium batteries and are
not reusable. Be sure to properly dispose of used lithium
batteries according to your local hazardous waste disposal
laws.
Specifications
Compatible panel
ClareOne (CLR-C1-PNL1)
Transmitter frequency
433MHz
Encrypted
Yes
Transmitted indications
Tamper and low batter
Supervisory keep-alive
60 to 70 minutes
Maximum UL spacing
50 x 50 ft (15.2 x 15.2 m)
Rate of rise rating
12 to 15°F (6.7 to 8.3°C)
UL max ambient
ceiling
100 to 150°F (37.8 to 65.6°C)
Battery type
CR123A
Battery life
8 to 10 years
Temperature detection
135º F rate of rise
Heat rate of rise
detection
15º F per minute
Operating environment
Temperature
Relative humidity
32 to 150°F (0 to 65.6°C)
0 to 95% noncondensing
Dimensions
2.29 × 1.28 in.
(58.25 × 32.4 mm)
Certifications
FCC: 15.109 Class B 15.231, Industry
Canada: ICES-003, RSS-210
Regulatory information
Manufacturer
Clare Controls, LLC.
7519 Pennsylvania Ave, Suite 104
Sarasota, FL 34243
\FCC compliance
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no guarantee
that interference will not occur in a particular
installation.
If this equipment does cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the
equipment and receiver.
•Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
•Consult the dealer or an experienced
radio/TV technician for help.
This device complies with Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired operation
of the device.
Cet appareil est conforme avec Industrie Canada
exempts de licence standard RSS (s). Son
fonctionnement est soumis aux deux conditions
suivantes: (1) cet appareil ne doit pas provoquer
d'interférences et (2) cet appareil doit accepter
toute interférence, y compris celles pouvant
causer un mauvais fonctionnement de l'appareil.
In accordance with FCC requirements of human
exposure to radio frequency fields, the radiating
element shall be installed such that a minimum
separation distance of 20 cm is maintained from
the general population.
FCC: 2ABBZ-RF-RORS-433
IC: 11817A-RFRORS433
This Class B digital apparatus complies with
Canadian ICES-3B.
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
MANUFACTURER HEREBY DISCLAIMS ALL
WARRANTIES AND REPRESENTATIONS,
WHETHER EXPRESS, IMPLIED, STATUTORY

DOC ID - 1945 • Rev 03 3 / 3
OR OTHERWISE INCLUDING (BUT NOT
LIMITED TO) ANY WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE WITH RESPECT TO
THESE PRODUCTS AND ANY RELATED
SOFTWARE. MANUFACTURER FURTHER
DISCLAIMS ANY OTHER IMPLIED WARRANTY
UNDER THE UNIFORM COMPUTER
INFORMATION TRANSACTIONS ACT OR
SIMILAR LAW AS ENACTED BY ANY STATE.
(USA only) SOME STATES DO NOT ALLOW
THE EXCLUSION OF IMPLIED WARRANTIES,
SO THE ABOVE EXCLUSION MAY NOT APPLY
TO YOU. THIS WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS AND YOU MAY
ALSO HAVE OTHER LEGAL RIGHTS THAT
VARY FROM STATE TO STATE.
MANUFACTURER MAKES NO
REPRESENTATION, WARRANTY, COVENANT
OR PROMISE THAT ITS ALARM PRODUCTS
AND/OR RELATED SOFTWARE (I) WILL NOT
BE HACKED, COMPROMISED AND/OR
CIRCUMVENTED; (II) WILL PREVENT, OR
PROVIDE ADEQUATE WARNING OR
PROTECTION FROM, BREAK-INS,
BURGLARY, ROBBERY, FIRE; OR (III)
WILL WORK PROPERLY IN ALL
ENVIRONMENTS AND APPLICATIONS.
Environmental
class
UL: Indoor dry
IEC: 3K5
EU compliance
EN 54
EN 54-00:0000
European Union
directives
1999/5/EC (R&TTE directive): Hereby, Clare
Controls declares that this device is in
compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC.
2002/96/EC (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive): This product
contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union.
See the product documentation for specific
battery information. The battery is marked with
this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury
(Hg). For proper recycling, return the battery to
your supplier or to a designated collection point.
For more information see: www.recyclethis.info.
Warranty information
Clare Controls offers a two (2) year limited warranty on original
Clare Controls components, from the date of shipment from
Clare Controls.
Contact information
Clare Controls, LLC.
7519 Pennsylvania Ave, Suite 104
Sarasota, FL 34243
General: 941.328.3991
Fax: [phone]
www.clarecontrols.com
Integrator/Dealer Support: 941.404.1072
[email protected]
Homeowner Support (ClareCare): 941.315.2273 (CARE)
[email protected]