Clarke WOODWORKER CWL325V Manual

GC0710
VARIABLE SPEED LATHE
Model No CWL325V
Part No 6501660
OPERATING & MAINTENANCE
INSTRUCTIONS
OPERATING & MAINTENANCE
INSTRUCTIONS

2
INTRODUCTION
Thank you for purchasing this CLARKE Wood Lathe.
Before attempting to operate the machine, it is essential that you read this
manual thoroughly and carefully follow all instructions given. In doing so you
will ensure the safety of yourself and that of others around you, and you can
also look forward to the product giving you long and satisfactory service.
GUARANTEE
This CLARKE product is guaranteed against faulty manufacture for a period of
12 months from the date of purchase. Please keep your receipt as proof of
purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
ENVIRONMENTAL PROTECTION
Do not dispose of this product with general household waste. All tools,
accessories and packaging should be sorted, taken to a recycling
centre and disposed of according to the laws governing Waste
Electrical and Electronic Equipment.
SAFETY SYMBOLS
The following safety symbols are displayed on the machine.
Wear dust protection
Wear eye protection
Read instructions before use

3
CONTENTS
Introduction ............................................................................................ 2
Guarantee .............................................................................................. 2
Environmental Protection ...................................................................... 2
Safety Symbols ....................................................................................... 2
General Safety Rules ............................................................................. 3
Electrical Connections .......................................................................... 6
Main Components ................................................................................. 7
Unpacking & Assembly ......................................................................... 8
Operation ............................................................................................. 10
Maintenance ........................................................................................ 10
Technical Specification ....................................................................... 11
Troubleshooting .................................................................................... 12
Parts List and Diagrams ....................................................................... 13
Declaration of Conformity .................................................................. 15
GENERAL SAFETY RULES
Important Note: Although the operation manual contains extensive instruction
on the safe working with power tools, every power tool involves some risk
which cannot be completely excluded. Power tools must therefore always be
operated with caution.
WORK AREA SAFETY
1. Keep work area clean and well lit. Cluttered or dark areas invite
accidents.
2. Do not operate power tools in explosive atmospheres, such as In the
presence of flammable liquids, gases or dust. Power tools create sparks
which may Ignite the dust or fumes.
3.
Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
ELECTRICAL SAFETY
1. Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.

4
2. Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
3.
Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
4.
Do not abuse the cable. Never use the cable for pulling or unplugging the
power tool. Keep cable away from heat, oil, sharp edges or moving parts.
Damaged or entangled cables increase the risk of electric shock.
5. If operating a power tool in a damp location is unavoidable, use a
residual current device (RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
PERSONAL SAFETY
1. Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in serious personal
injury.
2. Use personal protective equipment. Always wear eye protection.
Protective equipment such as dust mask, non-skid safety shoes, or hearing
protection used for appropriate conditions will reduce personal injuries.
3.
Prevent unintentional starting. Ensure the switch is in the off-position
before connecting to power source.
4. Remove any adjusting key or wrench before turning the power tool on . A
wrench or a key left attached to a rotating part of the machine may result
in personal injury.
5.
Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
6.
Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
7. Use of dust collection can reduce dust-related hazards.
POWER TOOL USE AND CARE
1. Do not force the machine. The machine will do the job better and safer at
the rate for which it was designed.
2. Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch Is dangerous and
must be repaired.
3.
Store power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the tool.
Power tools are dangerous in the hands of untrained users.

5
WARNING: DUST GENERATED FROM CERTAIN MATERIALS CAN BE
HAZARDOUS TO YOUR HEALTH. ALWAYS OPERATE THE LATHE IN A WELL
VENTILATED AREA. USE A DUST COLLECTION SYSTEM WHENEVER
POSSIBLE.
4.
Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the tool’s
operation. If damaged, have the tool repaired before use. Many
accidents are caused by poorly maintained power tools.
5. Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
6.
Use the power tool, accessories and tool bits etc in accordance with
these instructions, taking into account the working conditions and the
work to be performed. Use of the power tool for operations different from
those intended could result in a hazardous situation.
SERVICE
1. Have your power tool serviced by a qualified repair person using only
identical replacement parts . This will ensure that the safety of the power
tool is maintained.
ADDITIONAL SAFETY RULES FOR WOODLATHES
1. IMPORTANT: You should familiarise yourself with woodlathes and turning
techniques before using the machine. If there is any doubt whatsoever
you should consult a qualified person.
2. ALWAYS store chisels safety when you have finished with the machine.
3. CAUTION: This machine is designed for use with woodturning chisels only.
4. NEVER attempt to turn a workpiece unless a suitable support is used.
5. ALWAYS stop the lathe before removing workpieces, work supports or
swarf from the table.
6. ALWAYS be sure that the workpiece is securely locked in position.
7. ALWAYS keep hands and fingers away from the moving workpiece.

6
ELECTRICAL CONNECTIONS
WARNING! Read these electrical safety instructions thoroughly
before connecting the product to the mains supply.
Before switching the product on, make sure that the voltage of your
electricity supply is the same as that indicated on the rating plate. This
product is designed to operate on 230VAC 50Hz. Connecting it to any other
power source may cause damage.
This product may be fitted with a non-rewireable plug. If it is necessary to
change the fuse in the plug, the fuse cover must be refitted. If the fuse cover
becomes lost or damaged, the plug must not be used until a suitable
replacement is obtained.
If the plug has to be changed because it is not suitable for your socket, or
due to damage, it should be cut off and a replacement fitted, following the
wiring instructions shown below. The old plug must be disposed of safely, as
insertion into a mains socket could cause an electrical hazard.
WARNING! The wires in the power cable of this product are
coloured in accordance with the following code:
Blue = Neutral Brown = Live Yellow & Green = Earth
If the colours of the wires in the power cable of this product do not
correspond with the terminal markings of your plug, proceed as follows.
• The wire which is coloured Blue must be connected to the terminal which
is marked Nor coloured Black.
• The wire which is coloured Brown must be connected to the terminal
which is marked Lor coloured Red.
• The wire which is coloured Yellow & Green must be connected to the
terminal which is marked Eor coloured Green.
Plug must be BS1363/A approved
Earth Always fit a 13 Amp fuse.
(Green & Yellow
Neutral Live
(Blue) (Brown)
Ensure that the outer sheath of the cable is firmly held by the clamp
We strongly recommend that this machine is connected to the mains supply
via a Residual Current Device (RCD)
If in doubt, consult a qualified electrician. DO NOT attempt repairs yourself.

7
MAIN COMPONENTS
A B C D E F
GH I J K
G ON/OFF Switch
H Speed Control
I Thermal Overload Reset Button
J Tool Rest Support
K Tool Rest Locking Lever
A Faceplate
B Headstock Drive Centre
C Tool Rest
D Tail-stock Spindle
E Tail-stock Body
F Tail-stock Advancing Handle
ACCESSORIES
The following range of accessories are also available from your Clarke dealer:
8-Piece Chisel Set Part No: 6500649
4-Jaw Independent Lathe Chuck Part No: 6500645
1/2” Cap. 1MT Tailstock Chuck Part No: 6500643
2” Mini Chuck Set Part No: 6501662

8
UNPACKING
When unpacking, check for damage or omissions etc. Any found should be
reported to your CLARKE dealer where the appliance was originally
purchased. Do not discard the packaging until the machine is assembled.
The following items are supplied loose:
1 x Lathe
1 x Tool Rest, 110mm
1 x Tool Rest, 170mm
1 x Face Plate, 145mm dia
1 x Headstock Centre Spur
1 x Tailstock Centre Spindle
1 x Tailstock Locking Lever
1 x Tool Spindle Locking Lever
1 x Tool Rest Support Locking Lever
1 x Toolrest Locking Lever
1 x Fixings Pack
1 x Drift Rod
1 x Open Spanner
2 x Allen Keys (3mm & 5mm)
1 x Instruction Manual (this document)

9
Fig 3
Fig 1
Fig 2
ASSEMBLY
1. Screw the tailstock spindle into
the tailstock as shown in Fig 1.
Note: A left-hand thread is used
for this.
2. Attach the tailstock spindle
locking lever and the tailstock
locking lever in their postions
using the coil spring and
machine screw provided.
3. Attach the tool rest locking lever
and the support locking lever in
their postions using the coil
spring and machine screw
provided for each as shown in
Fig 2.
4. Install the tool rest of your
choice into the hole in the tool
rest support. Position the
working edge of the rest parallel
with the centre axis of the lathe
and secure with the tool rest
locking lever.
The position of the support will
be adjusted to suit the
workpiece.
5. Screw the faceplate onto the headstock
spindle while inserting the drift rod into
the hole in the spindle to prevent it from
turning. Tighten the faceplate using the
open spanner provided as shown in Fig 3.
6. If the work is to be held in position
between the headstock and tailstock,
insert the headstock spur into the
tapered hole in the headstock spindle.
Provided the faceplate is fitted, the spur
can be removed later by driving it away
from the headstock by unscrewing the
faceplate with the spanner in the usual
way.

10
OPERATION
1. Press the green push-button to start the lathe and adjsut the speed using
the speed control knob.
2. Always use the lowest speed when starting a new workpiece.
3. Always rotate the workpiece by hand before turning on the motor and
check it does not strike the tool/tool rest.
4. Ensure tool rest and tailstock are securely locked in position before starting
work.
5. Always position the tool-rest just above the centre-line of the lathe.
6. Avoid turning timber which has splits or substantial knots or voids and take
special care if these are discovered.
7. When turning, always roughly turn the work to a round form at slow speed.
8. Take care that the turning tools do not bite suddenly into the workpiece.
MAINTENANCE
For maximum performance, it is essential that the machine is properly
maintained. Always inspect before use. Any damage should be repaired and
faults rectified. The machine requires very little maintenance other than the
following guidelines.
IMPORTANT - Disconnect from mains power before cleaning.
1. Vacuum clean any dust or shavings that accumulate in or on the motor.
2. Check all cables periodically and ensure that they are in good condition
and not cracked.
3. Check the tightness of the mounting bolts.
4. Check the drive belt for wear and replace if it is frayed or otherwise
damaged.
5. Periodically lubricate the tail-stock, screw threads with engine oil such as
SAE20 or SAE30 grade if they become stiff to use.
6. Lightly lubricate the tail-stock and tool-post locking handles with oil if they
become difficult to use.
• The ball bearings in the headstock and tail-stock spindles are greased and
permanently sealed at the factory and require no further lubrication.
REPLACING THE BELT
Note: Part numbers refer to the Parts Diagram on page 13.
1. Undo the three screws (28) and remove the end cover (27).

11
2. Using the allen key supplied,
loosen the bolts (39) to enable
the motor to move and the drive
belt to go slack.
3. Dismount the drive belt from the
motor pulley (34) and then lift it
off the drive pulley (31) towards
you. Use the allen key to help you
as shown in Fig 4. The belt can
now be removed from the
headstock frame.
4. Replacement is a reversal of the
removal procedure. Tension the belt by hinging the motor downwards
prior to tightening the bolts (39).
Please refer to TROUBLESHOOTING on page 12. If you are unable to rectify
any faults, please contact your local dealer or Clarke International Service
Department on 0208 988 7400 for assistance.
Fig 4
TECHNICAL SPECIFICATION
Please note that the details and specifications contained herein, are correct at the
time of going to print. However, CLARKE International reserve the right to change
specifications at any time without prior notice.
erutaeF noitacificepS
thgieWgk12
)HxWxL(snoisnemiD )txetserloot&kcotsliat(mm003x222x237
deepS )elbairav(mpr0913-098
sertnecneewtebecnatsiDmm523
yticapaCgninruTmm002
daerhTeldnipS )FNU(IPT61x"4/3
gnitaRPI02PI
ycneuqerf/egatlovrotoMzH05/V032
egattaWtupnIdetaRW052
leveLerusserPdnuoS )A(BdApL5.28dedaoL/3.57daoloN
leveLrewoPdnuoSderusaeM )A(BdAwL8.19dedaoL/3.48daoloN

12
MELBORP SESUAC SNOITSEGGUS
.nurtonlliwrotoMnekorb/evitcefeD.1
.hctiws
.elbacrewopdegamaD.2
esool,tiucricnepO.3
denrubrosnoitcennoc
.rotomtuo
tiucricroesufnwolB.4
.rekaerb
.egatlovwoL.5
rofrelaedekralCruoyotdneS
.riaper
rofrelaedekralCruoyotdneS
.tnemecalper
tiucrictes-erroesufecalpeR
rehtoffonruT.rekaerb
.tiucricemasehtnosenihcam
rofylppusrewopehtkcehC
rehtonaesU.egatlovtcerroc
deifilauqaevahrotiucric
rewopehtedargpunaicirtcele
.ylppus
tratstonlliwrotoM
tiucricrosesufdna
.tuopirtrekaerb
rorotomnitiucrictrohS.1
.elbacrewop
tiucricrosesuftcerrocnI.2
.srekaerb
rofrelaedekralCruoyotdneS
.riaper
roesuftcerrochtiwecalpeR
.tiucricehtrofrekaerbtiucric
otsliafrotoM
.rewopllufhcaer
.tiucricdedaolrevO.1
noisnetxeelbatiusnU.2
.elbac
.yrter&senihcamrehtoffonruT
ezistcerrochtiwecalpeR
.elbacnoisnetxe
.sllatsrotoM.rotomnitiucrictrohS.1
tiucricrosesuftcerrocnI.2
.srekaerb
.tiucricdedaolrevO.3
.egatlovwoL.4
rofrelaedekralCruoyotdneS
.riaper
roesuftcerrochtiwecalpeR
.tiucricehtrofrekaerbtiucric
.yrter&senihcamrehtoffonruT
rofylppusrewopehtkcehC
rehtonaesU.egatlovtcerroc
deifilauqaevahrotiucric
ehtedargpunaicirtcele
.ecivres
noitarepoysioN.noisnettlebtcerrocnI.1
.eldnipsyrD.2
.yellupevirdesooL.3
eeS.noisnettlebtsujdA
nonoitces"tleBehtgnicalpeR"
.01egap
.eldnipsehtetacirbuL
wercs-tesgniniaterehtnethgiT
.yellupehtno
TROUBLESHOOTING

13
PARTS DIAGRAM

14
PARTS LIST
oN noitpircseD oN noitpircseD
1deB62tuNeldnipSkcotsdaeH
2etalPdnEgniniateR72revoCdnE
3wercSgnippat-fleS82wercS
4wercSburG92tfahScirtneccE
5leehwdnaH03wercsteS
6emarFkcotsliaT13yelluPevirD
7reveLgnikcoLllamS23tleBevirD
8ssoBdedaerhT33esaBtseRlooT
9eveelS43yelluProtoM
01tfahScirtneccE53elbaCrewoP
11eldnipSkcotsliaT63rellortnoCdeepS
21pilcriC73wercS
31ecargniraeB83tloBnoisneT
41ertneCrupSkcotsliaT93tloBdaeHtekcoS
51ertneCrupSkcotsdaeH04etalPtnuoMrotoM
61reveLgnikcoLegraL14rotoM
71etalpecaF24csiDgniniateR
81eldnipSkcotsdaeH34pilcriC
91ecaRgniraeB44tuNgniniateR
02pilcriC54rekaerBtiucriC
12tloBnoisneT64)pma01(esuF
22tseRlooT74redloHesuF
32ydoBkcotsdaeH84draoBtiucriCdetnirP
42gnirpSlioC94doRtfirD
52tloBlaicepS
When requesting spare parts, please quote the reference QBCWL325V
followed by the number (1-49) on the above parts list.

15
DECLARATION OF CONFORMITY