Clarke HLC400T Owner's manual

ASSEMBLY & USER
INSTRUCTIONS
ORIGINAL INSTRUCTIONS GC1119 - ISSUE 2
HALOGEN WORKLIGHT
MODEL NO: HLC400T (TWIN 230V)
PART NO: 5460695

2
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
INTRODUCTION
Thank you for purchasing this CLARKE double 400W twin halogen floodlight
and grill with tripod. This floodlight can be used with or without the tripod but is
designed for domestic use and should not be used on construction sites
Before attempting to use this product, please read this manual thoroughly and
follow the instructions carefully. In doing so you will ensure the safety of yourself
and that of others around you, and you can look forward to your purchase
giving you long and satisfactory service.
TECHNICAL INFORMATION
Model HLC400T
Model type 0808A-2
Dimensions (L x W x H) 485 x 205 x 385 mm (floor-standing)
870 x 770 x 900 min/1870 max (with tripod)
Weight 3 kg (floor-standing) / 5.3 kg (with tripod)
Tilt adjustment 95overticallly & 180ohorizontally
Operating Temperature -20oC to + 50oC
Power Supply 230V 50Hz
Insulation Class I
IP Rating IP54 (exterior use)
Rated input current 3.5 A
Weighted energy consumption 400 kWh/1000
Bulb Energy Efficiency Class# C class tube
Colour Temperature# 2900 K
Efficiency# 21.4 lm/W
Light output (luminous flux) # 2 x 8545 lm@1m (for the bulbs supplied)
Bulb (Halogen Tube Type) R7s-J118

3
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
SAFETY PRECAUTIONS
1. This worklight must not be immersed in water.
2. Do not look directly into the lamp when switched on as this can damage
the eyes.
3. If used with an extension cable always ensure that the extension cable is
fully unwound.
4. Do not use this worklight if it has a broken lens, casing or damaged cable.
5. Always unplug the worklight before moving it or performing maintenance.
Do not touch the lamp when your hands are wet.
6. Do not attempt to disassemble or repair the worklight.
7. Always unplug the worklight when it is not in use.
8. Never unplug the worklight by holding the cable. Always hold the plug.
9. Never use the worklight if the cable or plug are damaged.
10. Always stand on firm, level ground.
11. Do not cover the halogen bulbs or place combustable materials on top of
the worklight.
12. Do not use within 1m of combustable materials.
SAFETY SYMBOLS
The following symbols appear on the unit.
Hot surface, do not touch. Do not cover
ENVIRONMENTAL RECYCLING POLICY
Through purchase of this product, the customer is taking on the
obligation to deal with the WEEE in accordance with the WEEE
regulations in relation to the treatment, recycling & recovery and
environmentally sound disposal of the WEEE.
In effect, this means that this product must not be disposed of with general
household waste. It must be disposed of according to the laws governing
Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal
facility.

4
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
ELECTRICAL CONNECTIONS
Connect the mains lead to a standard, 230 Volt (50Hz) electrical supply
through an approved 13 amp BS 1363 plug, or a suitably fused isolator switch.
If the plug has to be changed because it is not suitable for your socket, or
because of damage, it must be removed and a replacement fitted, following
the wiring instructions shown below. The old plug must be discarded safely, as
insertion into a power socket could cause an electrical hazard.
If the colours of the wires in the power cable do not agree with the markings
on the plug.
• The BLUE wire must be
connected to the
terminal which is
marked N or coloured
black.
• The BROWN wire must
be connected to the
terminal which is
marked L or coloured
red.
• The YELLOW AND
GREEN wire must be
connected to the terminal which is marked E or or coloured green.
We strongly recommend that this product is connected to the mains supply
through a Residual Current Device (RCD)
If you are not sure, consult a qualified electrician.
WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS
THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS
SUPPLY.
WARNING: THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE
COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:
BLUE = NEUTRAL BROWN = LIVE YELLOW AND GREEN = EARTH
Plug must be BS1363/A approved.
Always fit
Ensure that the outer sheath of
Neutral
(Blue)
Live
(Brown)
Earth
(Green and
a 10 Amp
the cable is firmly held by the clamp
fuse.
Yellow)

5
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
ASSEMBLY & MOUNTING
The worklight can be used with or
without the tripod stand. The tripod
stand is supplied assembled and
should be erected before attaching
the worklamp assembly.
1. To erect the tripod, pull the legs
apart and set in position with the
leg locking screw.
• The assembly will be more
stable if the legs are set at
approximately 45 degrees.
2. Adjust the height of the tripod
column by twisting the locking
rings anti-clockwise to release,
and sliding the tubes to the
required height before twisting
clockwise to lock.
3. Attach the worklight to the
column by securing with the
central screw knob.
4. Secure the handles to each lamp
unit using the wingnuts supplied.
• Each lamp can be swivelled if
required by loosening the
screw knob beneath the lamp
and can be tilted to the
required angle.
5. If the halogen tube is not supplied already fitted, refer to the instructions
below for fitting/replacing the tube.
MAINTENANCE
The halogen tubes supplied have a life expectancy of approximately 1000
hours and can easily be replaced by the user. Always allow the worklight to
cool before perfoming any maintenance.
1. Release the screw holding the front lens closed and hinge it away from the
lamp body.

6
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
• The tube is a simple spring-fit in the holder at each end.
2. Do not touch the used tube if hot.
When handling the new tube, use
clean paper or cloth...DO NOT
allow your fingers to come into
contact with the glass. If this
happens, clean the glass with
methylated spirit.
3. Close the cover and re-tighten
the screw.
4. Clean the lens at regular intervals
using a non-abrasive glass cleaner.
Further replacement tubes can be obtained from your local dealer or Clarke
International Spares Department.
Type R7s-J118 - 230V -Max 400W Part No. 5460670
CARE & STORAGE
1. When not in use, switch off & unplug from the power supply.
2. Coil up the cable and hang it on the storage hooks on the tripod.
3. Store the worklight in a secure, dry place, out of the reach of children. Do
not leave it exposed to the elements, avoiding direct sunlight, heat, rain/
moisture etc.
4. Keep the external surfaces clean. Avoid impact damage & do not allow
this worklight to come into contact with abrasive or corrosive materials.
5. Do not use solvents, thinners or alcohol for cleaning, (with the exception of
the halogen tubes), as these chemicals will damage the finish. With the
worklight unplugged from the power supply, use a dry cloth to wipe over
the components.
6. Only use extension leads that are of an appropriate power rating and
suitable for the work environment. Inspect the extension lead regularly and
replace if damaged.
7. Never use unauthorised accessories or attachments which may result in
personal injury or damage to the product.
8. Do not attempt to repair or modify this product or attempt any electrical
repair yourself beyond replacing halogen tubes. Consult the Clarke Service
Department on 020 8988 7400.

7
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
DECLARATION OF CONFORMITY