Clarke LED700SR User manual

USER INSTRUCTIONS
ORIGINAL INSTRUCTIONS GC08/23
LED WORKLIGHT
MODEL NO: LED700SR
PART NO: 4003538

2
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
INTRODUCTION
Thank you for purchasing this CLARKE worklight.
Before attempting to use this product, please read this manual thoroughly and
follow the instructions carefully. In doing so you will ensure the safety of yourself
and that of others around you, and you can look forward to your purchase
giving you long and satisfactory service.
TECHNICAL INFORMATION
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase. This guarantee is invalid if the product is found
to have been abused or tampered with in any way, or not used for its
intended purpose.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission. This guarantee does not effect your
statutory rights.
Model LED700SR
Operating voltages 3.7V (light), 230V (charger)
Rated input power 7W
LED replaceable No
Rechargeable Lithium battery pack 3.7V / 6000 mAh
Lighting source COB 6W
Light output (luminous flux) 150-700 Lumen (20-100%)
Colour temperature (rendering) 5500-6800K
Battery charging time 4-5 hours
Approximate run time 3-13 hours
Rated lamp lifetime 30,000 hours
Efficiency (Lm/W) 150
Ingress protection rating IP67
Operating temperatures -10 to +40oC
Dimensions (H x W x D) mm Worklight - 45 x 200 x 63
Docking Station - 65 x 180 x 118
Weight Worklight - 400g
Docking Station - 260g

3
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
SAFETY PRECAUTIONS
1. DO NOT shine the worklight into anyone’s eyes.
2. Ensure the worklight is fully charged before initial use.
3. DO NOT use the worklight during recharging.
4. DO NOT use if you suspect that the battery or the casing is damaged.
5. Inspect the charger plug, cable & connector for damage to ensure items
are safe before connecting to the power supply. If damaged DO NOT use.
6. Check that the input voltage marked on the charger plug is the same as
the mains power supply to be used.
7. DO NOT disassemble the worklight for any reason.
8. DO NOT pull the charger from the mains socket by the lead.
9. DO NOT get the charger wet, or use in wet, damp conditions (the charger
is for indoor use only).
10. Never use any charger other than the one supplied with this product when
connecting to the power supply.
The following symbols may be displayed on the machine or its packaging.
ENVIRONMENTAL RECYCLING POLICY
Through purchase of this product, the customer is taking on the
obligation to deal with the WEEE in accordance with the WEEE
regulations in relation to the treatment, recycling & recovery and
environmentally sound disposal of the WEEE.
In effect, this means that this product must not be disposed of with general
household waste but according to the laws governing Waste Electrical and
Electronic Equipment (WEEE) at a recognised disposal facility.
The light source contained in this worklight has a life expectancy of
approximately 30,000 hours after which the worklight should be disposed of in
an environmentally responsible way.
The Lithium Ion battery falls under the Waste Batteries and Accumulators
Regulations 2009 and should be disposed of in a controlled manner.
May interfere with
pacemakers
Battery may be harmful to
aquatic or other life
Caution when disposing of
inflamable battery
Danger-explosive battery
materials

4
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
FEATURES & OPERATION
BATTERY CHARGING
1. Plug the docking station charging cable into a 230V power socket.
• The charge indicator turns red if charging the battery is desirable.
If the light is not being used for a long time keep it fully charged. Charging and
discharging at intervals of max 3 months helps to maintain performance.
BATTERY INDICATOR
The battery level LED indicator is on back of the worklight: Green = fully
charged / yellow = 50% / red = low
CHARGING INDICATOR
Charging status LED is displayed on the docking station: Red = charging /
Green = fully charged
• The worklight should not be operated while using the charger.
2. If you plan to store the worklight (e.g. for emergencies), we recommend
that the battery is fully charged before doing so. This will ensure the longest
possible battery life.
3. NEVER abuse the charger cable or yank the cable to disconnect it. Keep
the cable away from sharp edges/hot surfaces.

5
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
SWITCHING ON AND OFF
1. Press the power button once to turn the main light ON.
2. Press the power button twice to turn the main light OFF.
3. Press and hold the power button while the main light is on to start dimming.
To release, press and hold again to increase.
• Lowest and highest levels are indicated by flashing of the light until
the button is released.
• When the lamp is turned off it will remember the main light setting.
4. Attach the worklight to a suitable support using either the folding or
extending hook or attach to a ferrous metal surface using the magnet.
PAIRING
The light has been ‘paired’ to the docking station before leaving factory.
Please pair or remove pairing as per the following steps if needed.
1. When ‘pairing’, press and hold the power button on the light until the red
indicator lights up, then release.
2. Press the ‘call’ button on the dock station until the green indicator colour
changed, the red indicator on the light starts to flash simultaneously and
turns off.
3. To remove pairing, press and hold the power button on the light. The LED
indicator will be red, flashing and off.
FIND MY LIGHT FUNCTION
When you want to find the light that has been misplaced, press the dock call
button and release. You will hear beeps from the light and the light will flash.
Press the power button on the light to turn the alarm off.
• The ‘Find My Light’ function will not work once the light has no power
and may not work if the light is beyond 20 meters from the dock.
CARE & STORAGE
1. When not in use, switch off & unplug from the power supply. Store in a
secure, dry place, out of the reach of children. DO NOT leave it exposed to
the elements and avoid direct sunlight, direct heat, rain/moisture etc.
2. DO NOT use solvents, thinners or alcohol for cleaning, as these will damage
the finish. With the worklight unplugged, use a dry cloth to wipe the parts.
3. The LED light source cannot be replaced but has a life expectancy of
approximately 30,000 hours.
4. DO NOT attempt to repair this product or attempt any electrical repair
yourself. Consult the Clarke Service Department on 020 8988 7400.

6
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
COMPONENT PARTS
Item Description Item Description Item Description
1 Top Hook 8 Lamp Panel 15 Hook
2 Cover 9 Heat Sink 16 Bottom Cap
3 Top Cap 10 Battery Sleeve 17 Docking Bracket
4 Circuit Board 11 Lithium Battery 18 Back Shell
5 Moulded Shell 12 Bracket 19 Docking Circuit
6 Angle Ratchet 13 Lower Cap 20 Front Shell
7 Reflector 14 Magnetic Base 21 Switch

7
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
DECLARATIONS OF CONFORMITY