Clarke SMD84T/110 Owner's manual

ASSEMBLY & USER
INSTRUCTIONS
ORIGINAL INSTRUCTIONS GC1119 ISS 2
110V SMD LED WORKLIGHT
MODEL NO: SMD84T/110
PART NO: 4003640

2
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
INTRODUCTION
Thank you for purchasing this CLARKE portable LED floodlight which can be
used indoors or outdoors. Before attempting to use this product, please read
this manual thoroughly and follow the instructions carefully. In doing so you will
ensure the safety of yourself and that of others around you, and you can look
forward to your purchase giving you long and satisfactory service.
TECHNICAL INFORMATION
Model SMD84T/110
Model type L3305SJ-2
Dimensions (L x W x H) 58 x 870 x 1720 mm
Weight 4.9 kg
Light Source SMD LED array
Operating Temperature -20oC to + 50oC
Input power 42 W
Light Output (luminous flux) 3300 lumen
Power Supply 110V 50 Hz
Insulation Class II
IP Rating IP54
Energy Efficiency Class A+
Colour Temperature 6500 K
Weighted Energy Consumption 42 kWh/1000 h
Efficiency 78 Lm/W
Life Expectancy of LED 20,000 hours
LED type Epistar LED chip
Tilt adjustment -90oto +90o

3
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
SAFETY PRECAUTIONS
1. This worklight must never be immersed in water.
2. Do not look directly into the lamp when switched on as this can damage
the eyes.
3. If used with an extension cable always ensure that the extension cable is
fully unwound.
4. Do not use this worklight if it has a broken lens, casing or damaged supply
cable.
5. Always unplug the worklight before moving it or performing maintenance.
Do not touch the lamp when your hands are wet.
6. Do not attempt to disassemble or repair the worklight.
7. Do not leave the worklight unattended when switched on. Always unplug
the worklight when it is not in use.
8. Never unplug the worklight by tugging the cable. Unplug by holding the
plug.
9. Never use the worklight if the cable or plug are damaged.
10. When assembling the tripod, ensure that the ground is level and firm.
11. Take extra care not to push or knock the tripod over when fully extended.
12. Ensure the lamp is a safe distance from other objects in the working
environment.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.

4
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
EELECTRICAL CONNECTIONS
This product can be connected to one of the following power supplies:
• 110V generator
• 110V isolating transformer
• 110V site supply
• 230V generator via a 110V transformer.
Connecting it to any other power source may cause damage.
This product includes a fitted 3 pin industrial plug to BS-
EN 60309 (16A) and a cable for use with a 110 volt
supply. On no account must a 230V, 13amp (BS1363)
plug be used.
If using a portable 110V transformer make sure it has a
rated capacity sufficient to take the load of the
worklight.
Should the plug need changing at any time, ensure
that a plug of identical specification is used and
proceed as follows:
1. Undo the socket screws & remove the rear section.
2. Rotate the cable clamp clear of the terminals.
3. Feed the cable through the rear gland in the plug.
4. Remove the cable sheath to the required lengths
as shown in the diagram.
5. Terminate the correct wires in the
correct terminal blocks as shown.
6. Remove the cable clamp screws. Clip
the cable clamp back into position and
place the clamp around the outer
sheath of the cable. Replace the screws
and tighten until the cable is securely
held.
7. Replace the rear cover and tighten the cover screws.
If in any doubt, consult a qualified electrician.
WARNING! READ THESE ELECTRICAL SAFETY INSTRUCTIONS
THOROUGHLY BEFORE CONNECTING THE PRODUCT TO A
POWER SUPPLY.

5
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
ASSEMBLY
CONTENTS
• Pair of lamps wired to the
junction box & power cable.
•Tripodassembly
• Cross beam
• Hand screws/nuts/washers
ASSEMBLY
The tripod assembly may be erected
before attaching the other items. If
the end/upper tripod extension is not
visible, turn the locking ring and tilt
the tripod to slide the extension to
greater height.
1. Pull the legs apart to erect the
tripod and set in position with the
leg locking screw.
2. Adjust the height of the tripod
column by twisting the locking
rings anti-clockwise to release,
and sliding the tubes to the
required height before twisting
clockwise to lock.
3. Attach both the cross beam and
the junction box to the column by
securing with the hand screw.
4. Attach both the lamps to the
cross beam with the hand screws,
washers and nuts.
5. Tighten the hand screws on each
lamp to set the angle as required.
• Each worklamp can also be
tilted as required.
6. Switch on/off using the rocker
switch.

6
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
CARE & STORAGE
1. When not in use, switch off & unplug from the power supply. Coil the cable
around the storage hooks provided on the tripod for tidy storage.
2. This product should be stored in a secure, dry place, out of the reach of
children. DO NOT leave it exposed to the elements and avoid direct
sunlight, direct heat, rain/moisture etc.
3. Keep the external surfaces clean. Avoid impact damage & do not allow
this product to come into contact with abrasive or corrosive materials.
4. Do not use solvents, thinners or alcohol for cleaning, as these chemicals will
damage the finish. With the worklamp unplugged from the power supply,
use a dry cloth to wipe over the lamp components.
5. Only use extension leads that are of an appropriate power rating and
suitable for the work environment. Inspect the extension lead regularly and
replace if damaged.
6. The LED light source cannot be replaced but has a life expectancy of
approximately 20,000 hours.
7. Never use unauthorised accessories or attachments which can cause
personal injury or damage to the product.
8. Do not attempt to repair or modify this product or attempt any electrical
repair yourself. Consult the Clarke Service Department on 020 8988 7400.
ENVIRONMENTAL RECYCLING POLICY
Through purchase of this product, the customer is taking on the
obligation to deal with the WEEE in accordance with the WEEE
regulations in relation to the treatment, recycling & recovery and
environmentally sound disposal of the WEEE.
In effect, this means that this product must not be disposed of with general
household waste. It must be disposed of according to the laws governing
Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal
facility.

7
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
DECLARATION OF CONFORMITY