Clarke LED1000R User manual

INSTRUCTIONS FOR USE
GC06/23
RE-CHARGEABLE LED WORKLIGHT
MODEL NO: LED1000R
PART NO: 4006321

2
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
INTRODUCTION
Thank you for purchasing this CLARKE Worklight.
Before using this product, please read this manual thoroughly and follow the
instructions carefully. In doing so you will ensure the safety of yourself and that
of others around you, and you can look forward to your purchase giving you
long and satisfactory service.
TECHNICAL INFORMATION
Model LED1000R
Operating voltages 3.7V (battery), 5V(charging)
LED Wattage consumption 10W
LED replaceable No
Rechargable Lithium battery 3.7V / 2200mAh
Light output (luminous flux) 1000 Lumens
Colour temperature 6500K
Ingress Protection (IP rating) IP54
Battery charging time 2-3 hours
Approximate Run Time
(depending on battery life)
20% charged -2hr
50% charged - 4hr
100% charged - 8hr
Rated lamp lifetime 50,000 hours
Efficiency (Lm/W) 100m/W
Operating temperatures -20 to +45oC
Dimension 100 x 100 x 45mm
Weight 230g

3
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
SAFETY PRECAUTIONS
Read these instructions carefully before use and keep them for future reference.
1. DO NOT look directly into the worklight when it is switched on.
2. NEVER shine the light directly into anyone’s eyes including animals.
3. DO NOT use the worklight if the battery or the casing is damaged.
4. DO NOT disassemble the worklight for any reason.
5. DO NOT get the charger wet or use in wet, damp conditions (the charger is
for indoor use only).
6. NEVER use any charger other than the one supplied with this product when
connecting to the power supply.
7. Keep the worklight out of the reach of children.
8. Charge the worklight in a dry indoor location. DO NOT immerse in water or
any other liquid.
9. ALWAYS fully charge before first use.
10. This worklight utilises a rechargeable Lithium-ion battery that can rupture,
ignite and cause serious injury if used improperly.
11. Please check the following safety rules:
•DO NOT place batteries and worklight in a fire or high temperature.
•DO NOT tamper with battery wiring.
•DO NOT puncture or damage the batteries.
• The light source contained in this worklight has a life expectancy of
approximately 50000 hours after which the worklight should be
disposed of in an environmentally friendly way.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for its intended purpose.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission. This guarantee does not effect your
statutory rights.

4
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
OVERVIEW
OPERATION
1. Press the button in the following sequence.
• The worklight has four switching stages 25%, 50%,100%, Flashing, OFF
2. The worklight can be used while charging but has only 25% brightness in this
function. This function can only be used for a short duration.
3. The light has battery warning indicator. If the battery is almost discharged
the light will remain on for about 10 minutes, the LED light flashes 5 times
and the battery indicator flashes continuously until the light is switched off
or recharged.
4. Attach the worklight to a suitable support if required using the folding loop
or attach to a ferrous metal surface using the magnetic retainer.
5. To keep your worklight clean, wipe with a damp cloth only. DO NOT use
detergents, chemicals or harmful abrasives. NEVER immerse in water.

5
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
BATTERY CHARGING & CARE
1. ALWAYS fully charge the battery before first use.
2. DO NOT leave the lamp on charge for more than 24 hours.
3. Recharge the lamp every six months when in storage.
4. Connect the charging cable to the charging jack on the worklight. Always
use only the charging adaptor supplied.
5. Connect the other end of the charger to the 230V mains power supply and
charge until fully charged. Alternatively, charge the battery using the USB
cable connected to another electrical device.
• The battery condition indicator will illuminate when the lamp is
charging.
6. If you plan to store the worklight (e.g. for emergencies), we recommend
that the battery is fully charged before doing so. This will ensure the longest
possible battery life.
7. NEVER abuse the charger cable or pull the cable to disconnect it. Keep
the cable away from sharp edges/hot surfaces.
No parts of this worklight can be replaced.
ENVIRONMENTAL RECYCLING POLICY
Through purchase of this product, the customer is taking on the
obligation to deal with the WEEE in accordance with the WEEE
regulations in relation to the treatment, recycling & recovery and
environmentally sound disposal of the WEEE.
In effect, this means that this product must not be disposed of with general
household waste but according to the laws governing Waste Electrical and
Electronic Equipment (WEEE) at a recognised disposal facility.
The light source contained in this worklight has a life expectancy of
approximately 50000 hours after which the worklight should be disposed of in
an environmentally responsible way.
The Lithium Ion battery falls under the Waste Batteries and Accumulators
Regulations 2009 and should be disposed of in a controlled manner.

6
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
DECLARATION OF CONFORMITY-UK

7
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
DECLARATION OF CONFORMITY-CE

9
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]