Classic Exhibits Sacagawea Designs VK-2109 Manual

© 2020
Order #XXXXX
Locked layer contains
placeholder marks.
10’
20’
Top View
Perspective View
VK-2109 General Layout
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2020
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2020
Order #XXXXX
1) Locate channels along the edges of extrusions
2) Insert graphic corners first into channels then center
point of graphic into channels. Allows for proportional
fit around the perimeter of the extrusion.
3) Working from center to corner, slide silicon edge
on graphic into channel.
4) After all edges of graphic have been inserted into
channels, step back and assess graphic fit, make
adjustments where needed.
4
13
2
Fold edges over.
Insert into
groove
of frame
SEG Installation

© 2020
Case 1 of 2
Order #XXXXX
Graphics
Lights
Setup Hardware
& Connectors [B]
Top View of Each Level
Level 1 (Bottom Level) Level 2 Level 3
(2) Wings
Assembled Header
Base
Plate
10A 11
10
11A
Counter
Top
4C
A,A
6A
3A,3B
2B,2A
6B
4A, 4B, 5A, 5B
Graphic
Case Packing

© 2020
Case 2 of 2
Order #XXXXX
(4) Base Plates
Graphics
Top View of Each Level
Level 1 (Bottom Level) Level 2 Level 3
Assembled Header
Base
Plate
10A 11
10
11A
Counter
Top
5C
A,A
6A
2D,3D
2C,3C
6B
4A, 4B, 5A, 5B
(2) Wings
Case Packing

© 2020
Step 1 of 4
Order #XXXXX
Connection Bar A
1
1
1
1
Bolt
Clamp
Bolt Bolt
Bolt
4A
2A
2B
4B 4C
4A
4B
5A
6A
6A
6B
6B
5B 5C 5A
5B
Slide connection bar between
extrusions, then turn knobs
clockwise to tighten lock.
Straight Connection
with Knobs
Do not over tighten Knobs
Knob
Knob
Corner Connection
with Knob
Turn knob clockwise
to tighten lock.
Do not over tighten Knobs
Knob
B
B
B
Horizontal Placement
Stopper
Set upper horizontals
on top of stopper,
located on verticals.
Velcro on
Back/Bottom Edges
Velcro on
Back/Bottom Edges
Velcro on
Back/Top Edge
Velcro on
Back/Top Edge
Velcro on
Back/Inside Edges
of Verticals
Velcro on
Back/Inside
Edges of
Verticals
A
A
A
Velcro on extrusions
must face to BACK of
assembled Backwall.
B
FRONT VIEW
Item
1
2A,2B
3A,3B
2C,2D
3C,3D
4A,4B
5A,5B
4C,5C
6A,6B
Description
Base Plate
42” Vertical Extrusion w/ Clamps
42” Vertical Extrusion
42” Vertical Extrusion
42” Vertical Extrusion w/ Clamps
45” Horizontal Extrusion
45” Horizontal Extrusion
24” Horizontal Extrusion
2.5” Angle-Cut Vertical Extrusion
Qty.
4
1,1
1,1
1,1
1,1
2,2
2,2
1,1
2,2
Steps:
1) Attach base plates [1] to lower verticals [2A] [3A] [2C] and [3C], using bolts.
2) Connect verticals [2A to 2B] [3D to 3B] [2C to 2D] and [3C to 3D], using
connection bars [B]. See Straight Connection with Knobs detail.
3) Connect horizontals [4A to 4B] and [5A to 5B], using connection bars [A].
See Straight Connection with Knobs detail.
4) Attach vertical assemblies [2A/2B] [3A/3B] [2C/2D] and [3C/3D] with horizontal
assemblies [4A/4B] and [5A/5B]. See Corner Connection with Knob detail.
5) Connect graphics to Velcro on back side of frame.
Keep extrusions [6A] and [6B] attached to [2B] [3B] [2D] and [3D], as shown.
Keep clamps attached to [2A] [2B] [3C] and [3D].
3B
2C
2D
3C
3D
Keep connection bars [A] attached to [4A] and [5A] and [B] to [2A] [3A] [2C] and [3C].
3A
Backwall Assembly

© 2020
Step 2 of 4
Order #XXXXX
7
8
9
5A 5B
5A 5B
10
10A
11
11A
7
8
9
11A
10
10A
11
****
Steps:
1) Attach assembled header frames [7/8/9] to extrusions [5A/5B], then connect
graphics to Velcro on BACK of header frames.
2) Connect lights to extrusions [5A/5B]. See Light Connection detail.
3) Connect counter supports [10/11] to to [2A] and [3C].
4) Connect support legs [10A] to extrusions [10] of counter supports.
5) Attach shelf to extrusion [2A].
6) Attach counters to [11A]. See Counter Attachment sheet.
7) Route USB cords from counter. See USB Cord Management sheet.
8) Attach wings to clamps. See Clamp Attachment detail.
9) Attach sign to extrusion [3B], using standoffs and screw caps.
10) Attach monitor mount to extrusion [2B]. See Monitor Mount detail.
Keep extrusions [7] [8]
and [9] assembled.
3C
2A
2B
3D
Velcro on extrusions
must face to BACK of
assembled backwall. Velcro on extrusions
must face to BACK of
assembled backwall.
Shelf
*
Completed Assembly
*
Slide light onto clip then lock clip
into groove of horizontal extrusion.
Clip
Light
Light Connection
Clip
Light
Horizontal Extrusion
Keep extrusions [10]
and [11] assembled.
Monitor Mount
V4 Connectors
*
Slide connectors into groove
of extrusion. Tighten set screws
to secure connectors in place.
Attach monitor mount back
plate to extrusion, using bolts.
Bolts
Monitor
Mount
FRONT VIEW
Item
7/8/9
10A
10/11
11A
Description
Header Frame
Support Leg
Counter Support
Mounting Plate
Qty.
2
2
2
2
Knob
Set Screw
Connector
1) Slide connector of clamp
into extrusion groove.
2) Tighten set screw when
clamp is in position.
3) Insert wing into clamp.
4) Tighten knob on clamp
to secure wing in place.
Clamp Attachment
Clamp
Wing
Wing
Wing
Wing
Sign
Backwall Attachments

© 2020
Step 3 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
1) Mounting plate & wing nuts,
in packed position.
6) Place fixed counter bolts
into mounting plate, then
secure using wing nuts.
Completed Assembly
Counter Attachment
Wing Nut
Fixed
Bolts
Mounting
Plate [11A]
10
11
Counter
Attach mounting plate to curved extrusion
[10], using bolt. Insert fixed bolts, located
on underside of counter, into holes of flange
plate. Secure with wing nuts.
Mounting Plate
w/ Wig Nuts
Bottom view
of counter
Bottom view
of counter
10
11
Wing Nut
Wing Nut
Counter
2) Mounting plate bolt in,
packed position.
10
11
Bolt
Mounting Plate
Bolt
5) Tighten bolt, using hex tool,
to secure.
Mounting Plate
Bolt
3) Place mounting plate onto
[10] then tighten bolt, part
way, allowing some rotation
for final positioning.
4) Place fixed counter bolts
into mounting plate, then lift
counter to re-tighten bolt.
Bottom view
of counter Mounting Plate
10
Fixed
Counter
Bolt
Fixed
Counter
Bolt
Hex Tool
Keep mounting plate [11A] and wing nuts
attached to counter, when packing.
Keep bolt attached to [10], when packing.
Counter Attachment

© 2020
Step 4 of 4
Order #XXXXX
Route cord from right USB port
through right side of rubber clip
in groove of vertical extrusion.
Route cord from left USB port
through left side of rubber clip
in groove of vertical extrusion.
Cords will hang down
to USB outlet.
Plug USB cords into USB outlet.
USB Outlet
USB
Outlet
Rubber
Clip
USB
Cord
Wing
Vertical Extrusion
Vertical Extrusion
Wing
Wing
Wing ClampCounter Top
USB
Cords
USB
Cord
USB
Cord
Rubber
Clip
USB
Cord
USB
Cord
Keep rubber clip attached to vertical extrusion.
USB Cord Management