Classic Exhibits Sacagawea VK-1221 Manual

© 2018
Order #XXXXX
Scale: 17
10’
10’
Plan View
General Layout
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]

© 2018
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2018
Case 1 of 1
Order #XXXXX
Top View of Each Level
Level 1 Level 2
Assembled
Header
(4) Wings
2A,2B
6A 6B
3B,3A
A
5A, 4A, 4B, 5B
Graphics
Lights
Setup Hardware
Case Packing

© 2018
Step 1 of 2
Order #XXXXX
Item
1
2A/2B
3A/3B
4A/4B
5A/5B
6A/6B
Description
Base Plate
42” Vertical Extrusion
42” Vertical Extrusion
45” Horizontal Extrusion
45” Horizontal Extrusion
2.5” Angle-Cut Vertical
Qty.
2
1/1
1/1
1/1
1/1
1/1
Completed Backwall
(Front View)
Connection Bar
Back View
1
1
2A
2B
3A
3B
B
B
4A
4B
5A
5B A
A
Velcro:
Back/Bottom Edge
Velcro:
Back/Top Edge
6A
Steps:
1) Attach base plates [1] verticals [2A] & [3A], using bolts.
2) Connect verticals [2A] [2B] and [3A] [3B], using connection bars [B].
See Straight Connection with Knobs detail.
3) Connect horizontals [4A] [4B] and [5A] [5B], using connection bars [A].
See Straight Connection with Knobs detail.
4) Connect assemblies [2A/2B] and [3A,3B] with assemblies [4A,4B] and [5A,5B].
See Corner Connection with Knob detail.
5) Connect angled verticals [6A] to [2B] and [6B] to [3B].
See 2.5”h Angle-Cut Vertical Attachment detail.
6) Attach graphic to Velcro on back of assembled Backwall.
*
*
Velcro:
Back/Inside Edges
of Verticals
6B
Set Screw
Connector
2.5”h Angle-Cut
Vertical Attachment
Back View of Backwall
Insert connector into groove
of vertical extrusion, then
tighten set screw to secure.
*
Velcro
Slide connection bar between
extrusions, then turn knobs
clockwise to tighten lock.
Straight Connection
with Knobs
Do not over tighten Knobs
Knob
Knob
*
**
*
*
Corner Connection
with Knob
Turn knob clockwise
to tighten lock.
Do not over tighten Knobs
Knob
Velcro on extrusions
must face to BACK of
assembled Backwall.
Horizontal Placement
Stopper
Set upper horizontals
on top of stopper,
located on verticals.
Backwall Assembly

© 2018
Step 2 of 2
Order #XXXXX
3B
5B
5A
Graphic
7
9
8
*
*
Note: Hesder Frame extrusions
[7] [8] and [9] stay assembled.
Knob
Set Screw
Connector
1) Slide connector of clamp
into extrusion groove.
2) Tighten set screw when
A10 is in desired location.
3) Insert wing into clamp.
4) Tighten knob on clamp
to secure wing in place.
A10 Clamp
A10 Clamp
Steps:
2) Attach assembled header [7/8/9] to extrusions [5A/5B].
1) Connect lights to extrusions [5A/5B]. See Light Connection detail.
3) Attach graphic to extrusion [3B]. See Graphic Attachment detail.
8) Attach wings to clamps on [2A/2B] and [3A/3B]. See A10 Clamp detail.
Item
7/8/9
Description
Header Frame
Qty.
1/1/1
Completed Assembly
*
*
Connector
Graphic Attachment
Cap
Graphic
Standoff
Slide connector into groove of extrusion.
Tighten set screws to secure in place.
Screw standoff into connector. Place
graphic between standoff and cap,
then screw cap to secure graphic.
*
Slide light onto clip then lock clip
into groove of horizontal extrusion.
Clip
Light
Light Connection
Clip
Light
Horizontal Extrusion
Backwall Attachments