Classic Exhibits Visionary Designs VK-2967 Manual

© 2016
www.classicexhibits.com
Order #XXXXX -
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
VK-2967 General Layout
Plan View
20’
10’
Perspective View

© 2016
www.classicexhibits.com
Order #XXXXX -
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2016
www.classicexhibits.com
Order #XXXXX -
SEG Graphic Installation
1) Locate channels along the edges of extrusions
2) Insert graphic corners first into channels then center
point of graphic into channels. Allows for proportional
fit around the perimeter of the extrusion.
3) Working from center to corner, slide silicon edge
on graphic into channel.
4) After all edges of graphic have been inserted into
channels, step back and assess graphic fit, make
adjustments where needed.
LT Panel Assembly
1) With a vertical offset, place LT-Panels side-by-side;
slide vertically offset panel down to lock panels
together and in place.
2) Corner Connectors (90°, T-Connector, Straight Connector)
connect just as panels connect together. Repeat Step 1
for installing corner connectors to panels.
LT Panel Disassembly
1) To disassemble push panel with upper locks horizontally
to disengage top lock clip.
2) Slide panels or connectors vertically in opposing directions
to release latches and disconnect parts.



While pushed in,
pull panel up to
disassemble
Push Panel in to
disengage the lock.
Fold edges over.
Insert into
groove
of frame
General Information

© 2016
www.classicexhibits.com
Order #XXXXX -
Step 1 of 4
Backwall Assembly
2
2A
3A
4
6
6A
5
7
9
9
9
9
10
Infill
Infill
11
8
3
1
Item
1
2/2A
3/3A
4
5
6/6A
7
8
9
10
11
Qty.
1
1/1
1/1
1
1
1/1
1
1
4
1
1
Description
Boomerang Base Plate
95”h TSP46 Vertical Extrusion
48”w TSP46 Horizontal Extrusion
95”h TSP46 Vertical Extrusion w/ Door Hinge
95”h TSP46 Vertical Extrusion w/ A10 Clips
48”w TSP46 Horizontal Extrusion
95”h GS220 Vertical Extrusion w/ Door Stop
95”h Z45 Vertical Extrusion
24”w Z45 Horizontal Extrusion
44.417”w Mounting Plate
24”w Door Threshold
Steps:
1) Connect vertical extrusions [2] & [2A] between horizontals
extrusions [3] & [3A]. See TSV1 Lock Detail detail.
2) Attach Boomerang Base Plate [1] to base of extrusion [5].
See Boomerang Attachment detail.
3) Connect vertical extrusions [4] & [5] between horizontal
extrusions [6/6A]. See TSV1 Lock Detail detail.
4) Attach vertical extrusion [7] to assembly [2/2A/3/3A].
See Custom Cam Lock detail.
5) Connect lower horizontal [9] between verticals [5] & [8].
6) Insert large infill panel between verticals [5] & [8];
secure with upper horizontal [9].
7) Connect door threshold [11] between verticals [4] & [7].
See Door Attachment detail.
8) Attach assembled door to hinges on vertical [4].
See Door Attachment detail.
9) Connect horizontal [9] above door & between verticals [4] & [7].
NOTE: Leave enough space for door to open without conflict.
10) Insert small infill panel above door; secure with
horizontal [9].
11) Connect horizontal mounting plate between verticals [4] & [5].
12) Apply SEG graphics to assembled TSP
frames [2/2A/3/3A] & [4/5/6/6A].
See SEG Graphic Installation in General Information pages.
Door Attachment
Pin
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin
as shown.
Door
Hinge
Hinge
Door Threshold
Tighten
to secure
Slide into
groove
*
*
*
Door Threshold
Lock
Tighten setscrew
to secure
extrusions
TSV1 Lock Detail
*
*
*
*
*
*
*
**
Plan View
5
A10
TSP46
S10
Plan View
TSP46
S10
4
Plan View
GS220
PR37
7
Custom Cam Lock
*
Tighten screw to
secure TSP frame
into groove of
vertical extrusion.
TSP46
GS220
*
*

© 2016
www.classicexhibits.com
Order #XXXXX -
Step 2 of 4
Backwall Assembly Cont’d
22
2A
3A
4
6
6A
5
7
9
9
9
9
Infill
Infill
11
8
3
1
Item
1
2/2A
3/3A
4
5
6/6A
7
8
9
11
Qty.
1
1/1
1/1
1
1
1/1
1
1
4
1
Description
Boomerang Base Plate
95”h TSP46 Vertical Extrusion
48”w TSP46 Horizontal Extrusion
95”h TSP46 Vertical Extrusion w/ Door Hinge
95”h TSP46 Vertical Extrusion w/ A10 Clips
48”w TSP46 Horizontal Extrusion
95”h GS220 Vertical Extrusion w/ Door Stop
95”h Z45 Vertical Extrusion
24”w Z45 Horizontal Extrusion
24”w Door Threshold
Steps:
1) Connect vertical extrusions [2] & [2A] between horizontals
extrusions [3] & [3A]. See TSV1 Lock Detail detail.
2) Attach Boomerang Base Plate [1] to base of extrusion [5].
See Boomerang Attachment detail.
3) Connect vertical extrusions [4] & [5] between horizontal
extrusions [6/6A]. See TSV1 Lock Detail detail.
4) Attach vertical extrusion [7] to assembly [2/2A/3/3A].
See Custom Cam Lock detail.
5) Connect lower horizontal [9] between verticals [5] & [8].
6) Insert large infill panel between verticals [5] & [8];
secure with upper horizontal [9].
7) Connect door threshold [11] between verticals [4] & [7].
See Door Attachment detail.
8) Attach assembled door to hinges on vertical [4].
See Door Attachment detail.
9) Connect horizontal [9] above door & between verticals [4] & [7].
NOTE: Leave enough space for door to open without conflict.
10) Insert small infill panel above door; secure with
horizontal [9].
11) Apply SEG graphics to assembled TSP
frames [2/2A/3/3A] & [4/5/6/6A].
See SEG Graphic Installation in General Information pages.
Door Attachment
Pin
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin
as shown.
Door
Hinge
Hinge
Door Threshold
Tighten
to secure
Slide into
groove
**
*
Door Threshold
Lock
Tighten setscrew
to secure
extrusions
TSV1 Lock Detail
*
*
*
*
*
*
*
*
*
Plan View
5A10
TSP46
S10
Plan View
TSP46
S10
4
Plan View
GS220
PR37
7
Custom Cam Lock
*
Tighten screw to
secure TSP frame
into groove of
vertical extrusion.
TSP46
GS220
*
*

© 2016
www.classicexhibits.com
Order #XXXXX -
Step 3 of 4
Backwall Attachments
12 12
Item
12
12
Qty.
1
1
Description
Ceiling Canopy
Ceiling Canopy
Steps:
1) Attach ceiling canopy [12] & [12] to the top of assembled booth.
Use bolts provided.
2) Connect the monitor mount to the mounting plate [10].
See Monitor Mount Attachment detail.
3) Attach light to light receiving hardward on horizontal [3A].
See Light Attachment detail.
4) Connect Graphic Wings to verticals [5] using A10 Clips.
See A10 Clamp Detail detail. Wings attach to left and right assemblies.
*
*
*
*
*
*
*
*
*
*
*
Slide light into light
receiving hardware
Lock into
pill slot of
horizontal
Lock Light Receiving
Hardware into pill slot
of Horizontal Extrusion
pill slot
Light Attachment
Tighten set screw to
secure A10 to extrusion.
A10 Clamp Detail
Tighten knob to secure
wing in place.
1
2
3
*
Monitor Mount Attachment
*
Attach monitor plate to horizontal
using standoffs, bolts & wing nuts.
Wing Nut
Stand-off
Barrel
Bolts
Bolts

© 2016
www.classicexhibits.com
Order #XXXXX -
Step 4 of 4
MOD-1527 Kiosk Assembly
Shelf
13
When assembled
Item
13
Qty.
1
Description
70”h Vertical Extrusion
Steps:
1) Attach internal shelf supports using velcro;
insert internal shelf into kiosk cabinet.
2) Connect vertical extrusion [13] to cabinet body using
standoff caps from the inside of the cabinet.
See Cabinet to Post Attachment detail.
3) Place Counter top on top of cabinet.
See Counter Attachment detail.
4) Attach Monitor Mount to vertical [13].
See Monitor Mount Attachment detail.
Cabinet
Backwall
V4 Connector
Slide V4 connector into groove of vertical
extrusion; tighten set screw to secure.
Insert screw cap through hole of cabinet
backwall into threaded hole of V4 connector.
Twist and tighten screw cap to secure in place.
Cabinet to Post Attachment
Screw Cap
*
*
*
*
*
Shelf Supports
Align hole with pin Rotate pin. Spring
will push pin into hole.
Counter Top Attachment
12
*
Monitor Mount Attachment
1) Attach back plate to monitor.
2) Attach bolts to vertical.
3) Hang mounting plate from bolts.
4) Connect back plate to mounting
plate; use bolts, washers, and a nut.
*
*