Claypaky SCENIUS UNICO User manual

SCENIUS UNICO –User Menu
1
Main Menu
Level 1
Level 2
Level 3
Choices / Values
SET UP
DMX Address


001-512
Channel Mode


Standard
Vector
Fixture ID


000-255
Ethernet Interface
Control Protocol

Disabled
Art-net IP 2.x.x.x.
Art-net IP 10.x.x.x.
Art-net Custom IP
Repeat on DMX

Disabled
Enabled on primary
Universe

000-255
Custom IP Address
IP address byte 1
000-255
IP address byte 2
000-255
IP address byte 3
000-255
IP address byte 4
000-255
Custom IP Mask
IP mask byte 1
000-255
IP mask byte 2
000-255
IP mask byte 3
000-255
IP mask byte 4
000-255
SCENIUS UNICO
User Menu
01/2017

SCENIUS UNICO –User Menu
2
Main Menu
Level 1
Level 2
Level 3
Choices / Values
OPTION
Lamp DMX


On / Off
Pan / Tilt
Invert Pan

On / Off
Invert Tilt

On / Off
Swap Pan-Tilt

On / Off
Encoder Pan-Tilt

On / Off
P/T Homing mode

Standard
Sequenced
Pan Home Def Pos

0 degree
90 degrees
180 degrees
270 degrees
Tilt Home Def Pos

0 %
12.5 %
25 %
50 %
75 %
87.5 %
100 %
Color
Color Mixing

RGB / CMY
Fix Wheel Shortcut

On / Off
Dimmer Curve


Standard
Conventional
Shutter
Shutter On Error

On / Off
Dimmer On Shutter

On / Off
Lamp Dimming


1400W –1200W
1200W
Chg RotGobo Speed


Normal
Fast
Blades Speed


Normal
Fast
Display


On / Off
Setting
Default Preset
Reset To Default
Go Back
Are you sure ?
Yes / No
User Preset 1
Load preset 1
Save to preset 1
Are you sure ?
Yes / No
User Preset 2
Load preset 2
Save to preset 2
Are you sure ?
Yes / No
User Preset 3
Load preset 3
Save to preset 3
Are you sure ?
Yes / No

SCENIUS UNICO –User Menu
3
Main Menu
Level 1
Level 2
Level 3
Choices / Values
INFORMATION
System Errors


Read / Reset
Fixture Hours
Total Hours

Read
Partial Hours

Read / Reset
Lamp Hours
Total Hours

Read
Partial Hours

Read / Reset
Lamp Strikes
Total Strikes

Read
Partial Strikes

Read / Reset
System Version
CPU brd

Fw.rev. / Hw.rev.
com.dev

Fw.rev.
0:PT-3f

Fw.rev. / Hw.rev.
1: 8-Ch

Fw.rev. / Hw.rev.
2: 8-Ch

Fw.rev. / Hw.rev.
3: 8-Ch

Fw.rev. / Hw.rev.
4: 8-Ch

Fw.rev. / Hw.rev.
Board Diagnostic
0:PT-3f

Status / Err%
1: 8-Ch

Status / Err%
2: 8-Ch

Status / Err%
3: 8-Ch

Status / Err%
4: 8-Ch

Status / Err%
DMX Monitor
Channels

Value / Percentage
Fans Monitor
Ball. IN

Speed (RPM)
Ball. OUT

Speed (RPM)
Pwr. Sp.

Speed (RPM)
Pwr. Sp.

Speed (RPM)
Lamp

Speed (RPM)
Eff. OUT

Speed (RPM)
Eff. IN

Speed (RPM)
Blades

Speed (RPM)
Blades

Speed (RPM)
Lamp

Speed (RPM)
Sensor status
Channels

n.a / On / Off
Rot. Gobo Indexing


Indexing Active
Indexing Required
Network parameters


IP Address
IP Mask
MAC Address

SCENIUS UNICO –User Menu
4
Main Menu
Level 1
Level 2
Level 3
Choices / Values
MANUAL
CONTROL
Lamp


On / Off
Reset


Yes / No
Channel


Value / Percentage
TEST



Complete



Colors



Pan / Tilt
ADVANCED
Access Code 1234
Upload Firmware
Transfer ……..
Are you sure ?
Yes / No
Setup Model
Changing ……..
Are you sure ?
Yes / No
Calibration
Channels
000 - 255
Rot. Gobo Indexing
Starting procedure …..
Yes / No
Menu Locking

Unlock Code XXXX

SCENIUS UNICO –User Menu
5
SET UP MENU
DMX ADDRESS
PLEASE NOTE: Without the DMX input signal, the displayed address (DMX Address) blinks.
It lets you select the address (DMX Address) for the control signal. A DMX address between 001 and 512 can be
selected.
CHANNEL MODE
This lets you select the projector operating mode, selecting one of the two available modes:
Standard (37 DMX channels occupied, see DMX-Channel Function)
Vector (41 DMX channels occupied, see DMX-Channel Function)
FIXTURE ID
It lets you set the “Fixture ID” to be assigned to the projector. An “ID” between 000 and 255 can be assigned.
ETHERNET INTERFACE
It lets you set Ethernet settings to be assigned to the projector as indicated below:
Control Protocol
It lets you select the “Control Protocol” Art-net to be assigned according to the control unit used; the options available are
the following:
Disabled:
Art-net on IP 2
Art-net on IP 10
Art-net Custom IP
If the Control Protocol option is set on Disabled, when an IP address (IP2, IP10 or IP Custom) is selected, the projector
immediately initializes the IP address that was just selected.
If the Control Protocol option is enabled (IP2, IP10 or IP Custom) and a new one is selected that is different from the
previous one, the projector must be restarted so that it will be correctly initialized.
Repeat on DMX
It lets you enable/disable the transmission of the Ethernet protocol by DMX signal to all the connected projectors.
Disabled: DMX transmission disabled.
Enabled on primary: DMX transmission enabled.
Universe
It lets you set the “DMX Universe” to be assigned to a series of projectors with values between 000 and 255.
Custom IP Address
It lets you to set the select the “IP Address” Art-net to be assigned, according to the control unit used, with values
between 000 and 255.
Custom IP Mask
It lets you to set the select the “IP Mask” Art-net to be assigned, according to the control unit used, with values between
000 and 255.

SCENIUS UNICO –User Menu
6
OPTIONS MENU
LAMP DMX
It lets you enable (ON) the lamp remote control channel. Select OFF to turn off or disable this option.
PAN / TILT
Invert Pan
It lets you enable (ON) Pan reverse movement. Select OFF to turn off or disable this option.
Invert Tilt
It lets you enable (ON) Tilt reverse movement. Select OFF to turn off or disable this option.
Swap Pan-Tilt
It lets you enable (ON) Pan and Tilt channel inversion (and simultaneously Pan fine and Tilt fine). Select OFF to turn off or
disable this option.
Encoder Pan-Tilt
It lets you enable (ON) or disable (OFF) Pan and Tilt Encoder operations.
You can quickly disable the Pan and Tilt Encoder by simultaneously pressing the UP (↑) and DOWN(↓) keys in the
''Main Menu''.
P/T Homing Mode
It lets you set the initial Pan and Tilt Reset mode.
Standard: Pan & Tilt are simultaneously reset.
Sequenced: Tilt is reset first followed by Pan.
Pan Home Def Pos
It lets you assign the Pan channel “home” position at the end of Reset (without a DMX input signal), selecting one from
the 4 available positions:
0 degree
90 degrees
180 degrees
270 degrees (default)
Tilt Home Def Pos
It lets you assign the Tilt channel “home” position at the end of Reset (without a DMX input signal), selecting one from the
7 available positions:
0%
12.5%
25%
50% (default)
75%
87.5%
100%
COLOR
Color mixing
It lets you set the CMY color mixing system:
RGB color mixing mode (Red Green Blue)
CMY color mixing mode (Cyan Magenta Yellow)
Fixed wheel short-cut
Used for optimizing color change time (select ON) so that the disc turns in the direction that requires shorter movement.
Select OFF to turn off or disable this option.

SCENIUS UNICO –User Menu
7
DIMMER CURVE
It lets you select the “Dimmer Curve” from the two available:
Standard (default)
Conventional
SHUTTER
Shutter on error
It lets you activate (ON) automatic "Stopper/Strobe" closing in the event of Pan/Tilt positioning error. Select OFF to turn
off or disable this option.
Dimmer on Shutter
Enables (select ON) the automatic closing of the Dimmer when the Strobe is completely closed. Select OFF to turn off or
disable this option.
LAMP DIMMING
It allows you to select one of the two types of dimming available:
•1400W - 1200W lamp power operate as follows:
- Dimmer channel @ 0bit - lamp power @ 1000W
- Dimmer channel from 1 to 202bit - lamp power @ 1200W
- Dimmer channel from 203 to 255bit - lamp power increase from 1200W to 1400W
•1200W lamp power operate as follows:
- Channel dimmer @ 0bit - lamp power @ 1000W
- Dimmer channel from 1 to 255bit - lamp power @ 1200W
ROTATING GOBO CHANGE SPEED
It lets you select the speed of the Rotating Gobo Change from the two available:
Normal
Fast (default)
BLADES SPEED
It lets you select the speed of the Blades from the two available:
Normal
Fast (default)
DISPLAY
It lets you activate (ON) display brightness reduction after about 30 seconds in idle status. Select OFF to turn off or
disable this option.

SCENIUS UNICO –User Menu
8
SETTINGS
Used to save 3 different settings of the items in the option menu and relevant submenus.
Default preset (*)
User preset 1
User preset 2
User Preset 3
- Load preset 'X’ is used to recall a previously stored configuration.
- Save to preset ‘X’ is used to save the current configuration.
(*) DEFAULT PRESET
It lets you restore default values on all option menu items and relevant submenus.
Press the left and right arrows/keys simultaneously in the "main menu” to quickly restore default values
(DEFAULT PRESET).

SCENIUS UNICO –User Menu
9
INFORMATION MENU
SYSTEM ERRORS
It displays a list of errors that occurred when the projector was turned on.
To reset the SYSTEM ERRORS list, press OK. A confirmation message appears (Are you sure you want to clear error
list?). Select YES to confirm reset.
FIXTURE HOURS
It lets you view projector working hours (total and partial).
Total counter
It counts the number of projector working life hours (from construction to date).
Partial counter
It counts the number of projector partial working life hours from the last reset to date.
Press OK to reset the partial counter. A confirmation message appears on the display (Are you sure ?)
Select YES to confirm reset.
LAMP HOURS
It lets you view lamp working hours (total and partial).
Total counter
It counts the number of projector working hours with the lamp on (from construction to date).
Partial counter
It counts the number of lamp partial working hours from the last reset to date.
Press OK to reset the partial counter. A confirmation message appears on the display (Are you sure ?)
Select YES to confirm reset.
LAMP STRIKES
It lets you view how many times the lamp was turned on (total and partial).
Total counter
It counts the number of times the lamp was turned on (from construction to date).
Partial counter
It counts the number of times the lamp was turned on from the last reset to date.
Press OK to reset the partial counter. A confirmation message appears on the display (Are you sure ?)
Select YES to confirm reset.
SYSTEM VERSION
It lets you view the hardware and software versions for each electronic board in the projector.
CPU brd (CPU board)
0: PT-3f (Pan / Tilt board)
1: 8-Ch (8-channel board)
2: 8-Ch (8-channel board)
3: 8-Ch (8-channel board)
4: 8-Ch (8-channel board)

SCENIUS UNICO –User Menu
10
BOARD DIAGNOSTIC
It lets you view the percent errors for each electronic board installed in the projector
0: PT-3f (Pan / Tilt board)
1: 8-Ch (8-channel board)
2: 8-Ch (8-channel board)
3: 8-Ch (8-channel board)
4: 8-Ch (8-channel board)
DMX MONITOR
It lets you view the level of projector DMX channels in bit (Val) and in percent.
FANS MONITOR
It lets you view the speed of each fan installed in the projector:
Lamp (lamp cooling fan)
Pwr.Sup (PSU cooling fan)
Ball.IN (Ballast cooling fan, air-flow IN)
Ball.OUT (Ballast cooling fan, air-flow OUT)
Effect.IN (Effects cooling fan, air-flow IN)
Effect.OUT (Effects cooling fan, air-flow OUT)
Blades (blades cooling fan)
SENSOR STATUS
It lets you check the correct operations of each "sensor” installed in the projector, each channel is associated with one of
the following three parameters:
n.a.= sensor not available
ON= sensor working
OFF= sensor defective
ROT GOBO INDEXING
It lets you check whether the rotating gobo wheel 1 gobo indexing procedure should be run, if indexed, "Indexing Active"
appears on the display, otherwise "Indexing required!” appears
If necessary, indexing should be activated from the Advanced menu.
NETWORK PARAMS
Lets you view the projector "Network" parameters meaning:
IP address: Internet Protocol address (two projectors must not have the same IP address)
IP mask: 255.0.0.0
Mac address: Media Access Control; the projector’s Ethernet Address.