Clean Air Optima CA-702 Smart User manual

Model: CA-702 Smart
(EN) User manual
(DE) Gebrauchsanweisung
(NL) Gebruiksaanwijzing
(FR) Mode d’emploi
(ES) Manual del usuario
(PL) Instrukcja obsługi
(CZ) Uživatelská příručka
(RO) Manual de utilizare
(LT) Naudotojo vadovas
(EE) Kasutusjuhend
(LV) Lietošanas pamācība
Find more languages on:
www.cleanairoptima.com/
info/manuals
Read these instructions carefully before you start using this Clean Air Optima® device and keep the manual for future reference.
Clean Air Optima® 2in1: Dehumidifier & Air Purifier
© Copyright: Clean Air Optima
®
Manual

2
CA-702 Smart
Main unit

3
English
Thank you for purchasing the Clean Air Optima® 2in1: Dehumidifier & Air Purifier
CA-702 Smart.
We wish you many years of healthy indoor air with this ecient and eective product. Ensure
that all safety precautions are followed when using this electrical appliance for the proper
operation of the device. These instructions describe the safety precautions to be observed
during operation. They are meant to prevent injuries and to avoid damaging the device.
Description
This Clean Air Optima® device consists of the following main components:
1. Handle
2. Air outlet
3. Control panel
4. Water tank
5. Rubber feet
6. Air inlet
7. Filter frame compartment, includes: Pre-filter, Activated Carbon Filter,
True HEPA H13 Filter
8. Continuous drainage (water drain, hose connection) Drain hose 1 meter included
9. Power cord with humidity sensor

4
Safety warnings
This device may only be used in accordance with this safety instructions. Take the following
steps to minimize the risk of personal injury caused by for example electric shocks or fire.
1. Leave the device to stand for at least two hours before use, especially after
transportation.
2. Only for indoor use. Do not use or store outdoors.
3. Use proper voltage: AC 220V – 240V, 50Hz.
4. Allow a free space of min. 20 cm around the air inlet and air outlet of the device.
5. The appliance is not intended to be used by children or persons with reduced physical,
sensory or mental capabilities, unless they are supervised by a person responsible
for their safety.
6. Do not use the device when there is visible damage on the electrical cord or on the device
itself. Do not repair the device yourself in case of damage. Never pull the device by its
cord. If the power cord is damaged, then it must be replaced by an authorized service
person to prevent electric shock or fire.
7. Repairs may only performed by authorized service personal. Do not try to repair the
device yourself to prevent electric shock or fire.
8. Do not touch the power cord and plug with wet hands.
9. Always switch o the device before disconnecting the plug.
10. Never attempt to turn of the device by disconnecting the plug.
11. Pull the plug when you do not use the device or when you clean internal or external parts
of it.
12. For safety use put the device in a steady, horizontal position. Do not move while using.
13. Refrigerant: R290. This refrigerant complies with European environmental regulations.
No part of the cooling circuit may be perforated.
14. Do not use the device in rooms where inflammable liquids, gases are stored or close
to heat sources like radiator, fire place or heat-generating devices like ceramic heater.
15. Never insert any other object into the body to avoid breakdown.
16. Never cover the air inlet and air outlet grid.
17. Never dissemble or replace the device’s inner parts.
18. Use and store the device not under 0°C or above 40°C.
19. Do not tip the unit to any side when the water tank is full.
20. Do not put heavy objects on the unit.
21. Please avoid places with direct sunlight. There is a risk that the device discolors.
22. Never immerse the device in water or other liquids.
23. Empty the water tank regularly. In extreme conditions the water tank may be full after a
few hours operation.
24. Clean the Pre-filter regularly, if the Pre-filter is saturated with dust, it will lead to poor
purifying and dehumidifying eect. The power consumption will increase, it can cause
failure.
25. Replace the Activated Carbon Filter and True HEPA H13 Filter every 3 – 6 months, if the
Activated Carbon Filter and True HEPA H13 Filter are saturated, it will lead to poor
purifying and dehumidifying eect. The power consumption will increase, it can cause
failure.
26. Use, maintain and clean the device as described in this manual.

5
27. If you switch o the device, wait 10 minutes before switching it on again. This prevents
the compressor from being damaged.
28. Never connect the device to an external timer or unplug it while the device is in
operation.
Installation
Make sure that the distance from the device is 20 cm away from walls and furniture, see the
illustration below.
Filter installation (Hepa and activated carbon filter)
Dissassemble the panel, see red arrow.
Remove the sealing from the filters. Place the filters into the device. The tab must be visible at
the front.
Install the panel.

6
Control panel / Operation instruction
Power
Press the Power Button to activate the device.
Press the Power Button again, the device turns o.
Note: When the power light is flashing, the device is in defrost mode.
MODE
Press the MODE Button to select between Smart and Air Purifying.
Smart Mode (dehumidify air and purify air): The device will start dehumidifying when
the humidity increases to 5% above the desired humidity and will stop when the hu-
midity drops to 5% below the desired humidity. Use the humidity button to adjust the
desired humidity
Air Purifier Mode (only purify air) : The fan will run with no dehumidifying eect. This
is ideal when
you only want to use the device as an air purifier. This can also be used in combination
with the ioniser function.
Humidity setting (Only for MODE program: Smart Mode)
By pressing the Humidity Button, you can select the desired humidity level by
pressing this button repeatedly until the required humidity level is displayed
(from 35% to 80% in increments of 5%).
Once you select your desired humidity level, simply stop pressing the button and
your humidity level will be set. When the humidity level in the room reaches the set
humidity level, the device will stop dehumidifying and it will only purify air.
When the room’s actual humidity level increases again above your set humidity level
then the device starts dehumidifying again.
This button is also used to set the duration of the timer after pressing the TIMER
button.
UV and ION
After pressing once, the UV function is switched on.
After pressing twice the ION function is switched on.
After pressing three times, the ION and UV functions are switched on.
After pressing four times, the UV and ION functions are switched o.
Timer
Press TIMER button to program timer. When the timer is activated, the “TIMER” lamp
lights up. Before programming the timer, check that the timer function is not activated
(the light must be o). Following timer programs are available.
Power-on function: While the device is in standby, press the Timer button and then
use the button to set the number of hours you want the unit to start (1~24 hours).
Power-o function: While the device is running with the desired settings, press the
TIMER button and then use the button to set the number of hours after which you
want the device to stop (1~24 hours).

7
Sleep
Press the Sleep Button and the sleep mode is activated, the display will turn of.
Press the Sleep Button again to switch back in the settings before.
Child Lock
If you want to enter the CHILD LOCK function only, you need to turn on SLEEP mode
first and then press this button for three seconds. Then the SLEEP function will be
turned o and the CHILD LOCK function will be turned on.
Note: The SLEEP and CHILD LOCK functions are controlled by one button. When the
SLEEP function is o, press this button for three seconds enter the CHILD LOCK func-
tion, then the SLEEP function will be turned on together. So if you want to enter the
CHILD LOCK function only, you need to turn on SLEEP mode first, press this button for
three seconds. Then the SLEEP function will be turned o and the CHILD LOCK function
will be turned on.
Water Tank Full Indicator Light
When the water tank is full, the device will stop automatically. The Water Tank Full
Indicator Light turns on and lights up. Drain the water tank, and return the water tank
to the body of the device, the Water Tank Full Indicator Light will turn o. The device
will work automatically again.
Negative Ion
The negative ion generator has a total capacity of > 3.000.000 negative ions / cm²that
are spread through out the entire room and thereby neutralize pollutants and smells.
Negative ions attach onto dust particles, microorganisms and other unwanted particles
in the air and connect them to each other. This way, the particles become heavier than
air and fall onto the ground so that you can no longer breathe them in.
Negative ions are most found in the forest, mountains and by the sea. Negative ions
ensures fresh and healthy air.
Defrosting
The evaporator in the dehumidifier may defrost automatically if it is operated with a
room temperature less than 20 °C.
After the defrost mode is completed, the unit returns to the previous operating settings.
When the device is running in a room with a temperature between 5°C and 12°C , it will
go into defrost mode for 8 minutes approximately every 30 minutes.
When the device is running in a room with a temperature between 12°C and 16°C , it will
enter defrost mode for 5 minutes approximately every 60 minutes.
When the unit is running in a room with a temperature between 16°C and 20°C , it will
go into defrost mode for 5 minutes approximately every 90 minutes.
- During the defrosting operation, the dehumidification function and air purification function
may intermit.
- Don’t turn of the power or pull out the power plug of the device during the defrosting
operation.

8
Operation with Clean Air Optima® App
Connectivity
Compatibility with smartphone and tablet:
iPhone, iPad and Android devices
Device connets via WiFi with App:
CleanAirOptima
Attention: The router must be set to the 2.4 GHz broad-
band. If the router is set to the 5.0 GHz, it is impossible to
establish a connection.
Set up WiFi connection
1. Download and install the “CleanAirOptima” App in the
App Store or Google Play Store.
2. Make an account and log in.
3. The router must be set to the 2.4 GHz broadband. If the router is set to the 5.0 GHz, no
connection can be established.
4. Make sure Bluetooth is enabled on your smartphone.
5. Make sure that your smartphone or tablet is successfully connected to your WiFi network.
6. Plug the device into the power socket and switch it on. Press the mode button for 3-5
seconds, the WIFI light will start flashing.
7. Open the ‘CleanAirOptima’ App and click on ‘Add device’ . Your device is listed and you can
select it. If not choose ‘Auto Scan’. Follow the on-screen instructions to connect the device
to your network.
8. Choose to add the Clean Air Optima® device on the App, follow the instructions in the App.
9. When the device is paired, the WiFi indicator light stays on constantly.
10. After the configuration is successful, you can use the Clean Air Optima® App to operate the
device.
Note:
• If your default network has changed, reset the WiFi connection, follow step 1 to 9 in the
‘Set up WiFi connection’ section.
• If you want to pair multiple devices to your smartphone or tablet, you have to do this one
after the other.
• Make sure that the distance between your smartphone or tablet and the device is less than
5 meters and there are no obstacles. Also make sure you are in the same room as the
device.
Reset the WiFi function:
- The device must be switched on.
- Reset the WiFi by pressing the ‘Mode’ button for 3-5 seconds, the indicator light of the WiFi
will blink rapidly.

9
Turn o WiFi function:
- The device must be switched on.
- Reset the WiFi by pressing the ‘Mode’ button for 3-5 seconds, the indicator light of the WiFi
will blink rapidly.
- Turn of the WiFi by pressing the ‘Mode’ button for another 3-5 seconds, the indicator light of
the
WiFi will go out.
Connect devices to multiple phones
Note: First the other person needs to install the Clean Air Optima® App on his/her phone and
create a new account.
Share the device with limited access:
You can choose to share 1 device with several persons.
This person will then have access, but will not be able to manage all the settings.
Follow the instructions below to share the device with several persons:
1. Go to the relevant device.
2. Go to the pencil or three dots in the top right.
3. Select ‘Share device.‘
4. Choose ‘Add sharing‘.
5. Choose the sharing method e.g. via email, whatsapp, sms etc. and continue.
6. The device will automatically appear in the Clean Air Optima® App with the other account.
Share device with full access:
You can add a person or several persons to your home management.
That person will then have access to all your devices that are already linked and has full rights
and permissions. You will always remain the main administrator.
Follow the instructions below to add someone to your home management:
1. Open the Clean Air Optima® App and go to ‘Me’.
2. Then choose ‘Home Management’.
3. Choose ‘Create a home’.‘
4. Select the relevant ‘Home’ and ‘Add member‘.
5. Choose the sharing method e.g. via email, whatsapp, sms etc. and continue.
6. The corresponding ‘Home‘ will automatically appear in the Clean Air Optima® App of the
person with whom you have shared your ‘Home‘.
7. On the other account:
Go to the home screen from the Clean Air Optima® App. Go to the top left and select the
‘Home‘.

10
Water Drainage
The Water Tank Full Indicator Light will light up when the water tank is full. Take out the water
tank and empty the water inside. Then put the water tank back into the dehumidifier correctly,
see the illustration below.
Note:
When you remove the water tank, do not
touch sensors or any parts which are situated
behind the water tank. This may damage the
product. Push the water tank gently in the device.
Continuous Drainage
For continuous operation you can use the drain hose of 1 meter long that is included.
Water can be automatically plumbed in or drained into a sink, a larger recipient or through the
wall into an outside drain by attaching a pipe to the unit. Remove the rubber bung on the rear
of the unit and insert the pipe into the drain outlet at the back of the unit. Make sure the con-
nection between pipe and the drain outlet is tight and does not leak. Then direct the pipe to a
suitable drainage point. This unit uses gravity to dispose of water hence the drain should be
lower than the water outlet on the unit. Put the tank back. Be sure to run the water pipe down-
ward and let the water to flow out smoothly. Do not kink or bend the pipe.
Replacing the Clean Air Optima® True HEPA H13 Filter and Activated
Carbon Filter
The Clean Air Optima® CA-702 Smart Dehumidifier & Air Purifier is equipped with a filter lifes-
pan surveillance mechanism that signals that the filters have to be replaced after 400 work-
ing hours. To show that the filters needs to be replaced, the dehumidifier emits a double zero
indicator light in the display.
Reset the timer for the filter replacement by pressing and holding the Humidity button for
about 3-5 seconds. If the indicator light goes out, the timer has been successfully reset and
the dehumidifier is ready for use again.

11
Maintenance
Cleaning the housing of the Clean Air Optima® dehumidifier
1. Switch o the device and pull the plug.
2. Use a soft and humid piece of cloth to clean the device. Do not use chemical solvent such
as benzene, alcohol or gasoline.
3. Make sure that no water gets into the device, do not sprinkle with water.
Replacing of filters
Depending on the use, the Activated Carbon Filter and True HEPA H13 Filter has a lifespan of
approx. 3 – 6 months. The Pre-filter and UV-C lamp are permanent, no replacement needed.
Take out the filters from the filter frame compartment. After filter replacement or filter
cleaning reinstall the filters back into the filter frame compartment and assemble back to the
device, see the illustration below.
Filter cleaning
The best eect for a longer lifespan of the Filters is reached by cleaning the filters once a
month. If indoor air is extremely polluted, we advice to clean the filters more often ca. once per
two weeks.
Clean the Pre-filter, Activated Carbon Filter and True HEPA H13 Filter carefully with a brush or
your vacuum cleaner. That way bigger dust particles like lint, hair, dust and dander of pets can
be removed from the filters.

12
Room temperature increases during operation
The Clean Air Optima® dehumidifier doesn’t have a cooling function. The device will produce
heat during operation and increase the room temperature between 1 °C to 4 °C.
Dehumidifying capacity
The illustration below shows the dehumidifying capacity of the Clean Air Optima® dehumidifier.
By dierent temperatures and relative humidity, the dehumidifier may have dierent
dehumidifying capacities.
Humidity 80%
Dehumidifying capacity
Room temperature
Warning!
Do not damage the filters, the filters must not be cracked. Damaged filters needs to be
replaced.
Never wet or rinse the filters (Only for Activated Carbon Filter and True HEPA H13 Filter)
withwater. Filters that are rinsed with water needs to be replaced.
Signs for used up filters that needs to be replaced
(Only for Activated Carbon Filter and True HEPA H13 Filter)
Increased sound, reduced air flow, congested filters, rising presence of smells. Filters needs
also to be replaced by new ones when the True HEPA H13 Filter changes its color from white to
grey or black. If the True HEPA H13 Filter remains white, there is NO need to replace the filters.
How to order filters:
Contact Clean Air Optima® Customer Service tel. + 31 (0) 742670145 or visit our webshop:
https://www.cleanairoptima.com/-accessoires
Clean Air Optima® dehumidifier storage
If the dehumidifier will not be used for an extended period of time:
1. Drain the water tank completely and make sure that there is no water stocked
inside the water tank.
2. Unplug the device and fold up the power supply cord.
3. Remove and clean the filters. After cleaning reinstall the filters back into the device.
4. Store the dehumidifier in a cool, dry location, away from direct sunlight, extreme
temperature and excessive dust.

13
Troubleshooting
The following is a troubling shooting guide to help you solve any issues that you may have
using the Clean Air Optima® dehumidifier CA-702 Smart.
Problem Possible Cause Solution
Device does not
switch on
Ineciency
dehumidification
The power cord does not
connect correctly
The water tank is full or water
tank is not in the correct
position
The filters are blocked by dust
The air inlet and outlet have
ablockage
The setting humidity is higher
than environmental humidity
The dehumidifier is in
Continuous air purification
MODE
Connect the power plug and
power socket correctly
Drain the water tank and replace
the water tank to the correct
position
Clean or replace the filters
Clean the blockage from the air
inlet and outlet
Set the humidity at least 5%
lower than environmental
humidity
Change the operation MODE
Noise The device is installed askew
The filters are blocked
Make sure the device is installed
uprightly
Clean or replace the filters
Display shows double
zero .
Filters need to be replaced.
Reset the timer for the filter
replacement by pressing and
holding the Humidity button for
about 3-5 seconds. If the indica-
tor light goes out, the timer has
been successfully reset
Washed clothes are
not dried
The room temperature is to low
Washed clothes are hard to be
dried under low temperature
conditions
Operation with Clean
Air Optima® App does
not work
Smartphone or tablet is not
connected to WiFi network
The device has no connection to
the network
Switch o the device and reset
the WiFi on the device by
pressing the Mode button for 5
seconds, the indicator light of the
WiFi will blink rapidly. Than follow
step 4 to 8 from chapter
Operation with Clean Air Optima®
App

14
Problem Possible Cause Solution
E1 or E2 notification
display Humidity sensor error Use the device within the spec- ified humidity range. Unplug the
appliance and plug it back in.
E3 or E4 notification
display Temperatur sensor error
Use the device within the speci-
fied temperature range. Unplug
the device and plug it back in.
Dehumidifier does not
extract water
Is the device set to a lower hu-
midity level than in the room?
Is a suction grille or discharge
blocked? Is the device too close
to walls?
Set the humidity level on the hy-
grostat below the current humid-
ity value.
Remove obstacles and restart
the device.
Ensure a distance of at least 20
cm between the unit and walls.

15
WARNING!
If the above recommended solutions do not work, please contact Clean Air Optima® technical
support at the telephone number for your region. Do not attempt to disassemble, reassemble,
or repair the device as this may void the warranty.
Specifications CA-702 Smart
Model CA-702 Smart
For rooms up to 20m²/ 50m³/ 215ft²
Rated voltage 220V - 240V, 50Hz
Rated power 155W
Fan capacity 70 m³/h
Dehumidifying capacity 5 liters per day at 30°C and 80%RH
Working temperature range 5°C - 32°C
Water tank 1,5 liter
Air purification with: Pre-Filter, Activated Carbon Filter, True HEPA H13 Filter,
UV-C lamp, Ionizer
Filter performance 99,97%, Sterilization rate 99.9%
Negative ion >3.000.000 ions/cm²
Sound level 39dB(A)
Drain hose 1 meter
Dimensions 255 x 225 x 430mm
Weight 7kg
Colour White
Refrigerant R290 / 30g
Complies with EU regulations CE / WEEE / RoHS
Ask your retailer or your municipality for updated information regarding
the disposal of the packaging and of the device.
Danger
Natural refrigerant propane (R290)!

16
Service
Warranty Certificate for the Clean Air Optima® Dehumidifier
CA-702 Smart.
Date of purchase: …………………………………………………………………………………………
Customers name: …………………………………………………………………………………………
Address: …………………………………………………………………………………………………….
Telephone: ………………………………………………………………………………………………….
Email: ………………………………………………………………………………………………………..
Seller’s name: ……………………………………………………………………………………………...
Address: …………………………………………………………………………………………………….
1. Please fill in completely this Warranty Certificate. Send it with the invoice and the unit,
postage pre-paid and using the original packing box, to your distributor. Make sure to include
the appropriate return postage for the package.
2. Please enclose a short description of the damage, fault or malfunction, and the circum-
stances under which these problems arose.
The Clean Air Optima® Dehumidifier CA-702 Smart is subjected to strict
testing procedures before leaving the factory. If within two years from the date of purchase
the product does not perform according to the specifications, because of factory defects, the
purchaser is entitled to free repairs or replacement of parts upon presentation of this warranty
(provided that the malfunction or damage to the device and/or parts occurred under normal
operating conditions). What is covered: All parts defective in material and workmanship. For
how long: two years from purchase date. What we will do: Repair or replace any defective parts.
Other Conditions
The provisions of this warranty are in lieu of any other written warranty whether express or
implied, written or oral, including any warranty of merchantability or fitness for a particular
purpose. The manufacturer’s maximum liability shall not exceed the actual purchase price paid
by you for the product. In no event shall the manufacturer be liable for special, incidental,
consequential, or indirect damages. This warranty does not cover a defect that has resulted
from improper or unreasonable use or maintenance, faulty assembly, accident, natural ca-
tastrophes,
improper packing, or unauthorized tampering, alteration, or modification as determined solely
by us. This warranty is void if the label bearing the serial number has been removed or defaced.

17
Thank you
for reading!
Share your feedback about the Clean Air Optima®
Dehumidifier CA-702 Smart on:
www.cleanairoptima.com
For frequently asked questions about the CA-702 Smart
go to: www.cleanairoptima.com and search for the CA-702 Smart
Download PDF instruction manual on:
www.cleanairoptima.com/info/manuals
Watch all Clean Air Optima® Product
animation video’s on:
www.youtube.com
Clean Air Optima International B.V. | David Ricardostraat 9-7 / 9-9 | 7559 SH Hengelo (ov)
The Netherlands | Phone: +31 (0) 74 - 2670145
Clean Air Optima Germany GmbH | Enschedestraße 14 | 48529 Nordhorn | Germany
Phone: [phone]
E-mail: inf[email protected] Internet: www.cleanairoptima.com

18
CA-702 Smart
Hauptgerät

19
Deutsch
Vielen Dank, dass Sie sich für den Clean Air Optima® 2 in 1 entschieden haben:
Luftentfeuchter und Luftreiniger CA-702 Smart.
Wir wünschen Ihnen viele Jahre gesunde Raumluft mit diesem ezienten und eektiven
Produkt. Treen Sie für die ordnungsgemäße Funktion dieses elektrischen Geräts unbedingt
alle Sicherheitsvorkehrungen, wenn Sie das Gerät verwenden. Diese Anleitung beschreibt
die Sicherheitsvorkehrungen, die im Betrieb zu beachten sind. Sie sind dafür vorgesehen,
Verletzungen vorzubeugen und Beschädigungen am Gerät zu vermeiden.
Beschreibung
Dieses Clean Air Optima® Gerät besteht aus den folgenden Hauptkomponenten:
1. Gri
2. Luftauslass
3. Bedienfeld
4. Wassertank
5. Gummifutter
6. Lufteinlass
7. Filterrahmenfach, einschließlich: Vorfilter, Aktivkohlefilter, True HEPA H13-Filter
8. Kontinuierliche Entwässerung (Wasserablauf, Schlauchanschluss) Abflussschlauch 1Me-
ter im Lieferumfang enthalten
9. Stromkabel mit Luftfeuchtigkeitssensor

20
Sicherheitshinweise
Dieses Gerät darf nur in Übereinstimmung mit diesen Sicherheitshinweisen verwendet werden.
Führen Sie die folgenden Schritte aus, um das Verletzungsrisiko für Personen (z.B.durch
Stromschläge oder Feuer) zu minimieren.
1. Lassen Sie das Gerät vor dem Gebrauch mindestens zwei Stunden stehen, vor allem nach
dem Transport.
2. Nur für Innenräume geeignet. Nicht im Freien verwenden oder lagern.
3. Die richtige Spannung verwenden: AC 220V – 240V, 50Hz.
4. Lassen Sie um den Lufteinlass und den Luftauslass des Geräts einen Freiraum
vonmindestens 20 cm.
5. Das Gerät ist nicht für die Verwendung durch Kinder oder Personen mit eingeschränkten
körperlichen, sensorischen oder geistigen Fähigkeiten bestimmt, es sei denn, diese Personen
werden von einer für ihre Sicherheit verantwortlichen Person beaufsichtigt.
6. Verwenden Sie das Gerät nicht, wenn sichtbare Schäden am Netzkabel oder am Gerät selbst
vorhanden sind. Reparieren Sie das Gerät nicht selbst, wenn es beschädigt ist. Ziehen Sie
das Gerät niemals an seinem Kabel. Wenn das Netzkabel beschädigt ist, muss es von einer
autorisierten Person ausgetauscht werden, um einen Stromschlag oder Brand zu vermeiden.
7. Reparaturen dürfen nur von befugtem Servicepersonal durchgeführt werden. ZurVermeidung
von Stromschlägen und Bränden sollten Sie nicht versuchen, das Gerät selbst zu reparieren.
8. Das Netzkabel nicht mit nassen Händen berühren.
9. Immer das Gerät ausschalten, bevor Sie den Netzstecker abziehen.
10. Versuchen Sie niemals, das Gerät durch Ziehen des Steckers auszuschalten.
11. Den Netzstecker aus der Steckdose ziehen, wenn Sie das Gerät nicht benutzen oder wenn Sie
innere oder äußere Teile des Geräts reinigen.
12. Zur Sicherheit das Gerät in eine stabile, horizontale Position stellen. Während des Gebrauchs
nicht bewegen.
13. Kältemittel: R290. Dieses Kältemittel entspricht den europäischen Umweltvorschriften.
KeinTeil des Kühlkreislaufs darf perforiert sein.
14. Verwenden Sie das Gerät nicht in Räumen, in denen brennbare Flüssigkeiten oder Gase
gelagert werden, in der Nähe von Wärmequellen oder in besonders feuchten Räumen
(wieim Badezimmer).
15. Nie andere Gegenstände in das Gehäuse einführen, um Ausfällen vorzubeugen.
16. Nie den Lufteinlass und das Luftauslassgitter abdecken.
17. Nie die inneren Teile des Geräts zerlegen oder ersetzen.
18. Verwenden und lagern Sie das Gerät nicht unter 0°C oder über 40°C.
19. Neigen Sie das Gerät nicht zur Seite, wenn der Wassertank voll ist.
20. Keine schweren Gegenstände auf das Gerät stellen.
21. Bitte Orte mit direktem Sonnenlicht vermeiden. Es besteht die Gefahr, dass das
Gerätausbleicht.
22. Das Gerät niemals in Wasser oder andere Flüssigkeiten eintauchen.
23. Den Wassertank regelmäßig entleeren. Unter extremen Bedingungen kann der Wassertank
bereits nach wenigen Stunden voll sein.
24. Der Vorfilter sollte regelmäßig gereinigt werden, da ein mit Staub gesättigter Vorfilter zu einer
schlechten Reinigungs- und Entfeuchtungswirkung führt. Die Leistungsaufnahme steigt,
eskann zu Ausfällen führen.
25. Tauschen Sie den Aktivkohlefilter und den True HEPA H13-Filter alle 3 bis 6 Monate aus. Wenn
der Aktivkohlefilter und der True HEPA H13-Filter voll sind, wird die Reinigungs- und Entfeuch-
tungswirkung beeinträchtigt. Die Leistungsaufnahme steigt, es kann zu Ausfällen führen.
26. Verwenden, warten und reinigen Sie das Gerät wie in dieser Anleitung beschrieben.